Electronic Components Kit TIP120 for Arduino
  • Electronic Components Kit TIP120 for Arduino

Electronic Components Kit TIP120 for Arduino

B0100

check it Contenido:
- 20x Cable macho-macho 20cm - 10x Cable hembra-macho 20cm - Kit de diodos LED - 20 unidades ( 5x rojo, 5x verde, 5x amarillo, 5x blanco) Resistencias:
- 220R- 10 unidades
- 10k- 5 unidades
- 1k-   5 unidades
- Transistor TIP120 TO-220 - 1 unidad
- Diodo LED RGB - 1 unidad
- Condensador electrolítico 470uF/50V - 2 unidades check it Content:
- Prototype plate 400 points
- 20x Cable Jumper mach-macho
- LED diode kit - 30 units (10x red, 10x green, 10x yellow) Resistances:
- 100k- 10 units
- 10k- 10 units
- 1k- 10 units
- 220R- 10 units
- Photoresistor GL5516 Type LDR 10k - 2 units
- Push buttons Omron B3F Blue, Red, White - 3 units
- 100uF / 50V electrolytic capacitor - 5 units

OEM
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

check it Contenido:
- 20x Cable macho-macho 20cm - 10x Cable hembra-macho 20cm - Kit de diodos LED - 20 unidades ( 5x rojo, 5x verde, 5x amarillo, 5x blanco) Resistencias:
- 220R- 10 unidades
- 10k- 5 unidades
- 1k-   5 unidades
- Transistor TIP120 TO-220 - 1 unidad
- Diodo LED RGB - 1 unidad
- Condensador electrolítico 470uF/50V - 2 unidades check it Content:
- Prototype plate 400 points
- 20x Cable Jumper mach-macho
- LED diode kit - 30 units (10x red, 10x green, 10x yellow) Resistances:
- 100k- 10 units
- 10k- 10 units
- 1k- 10 units
- 220R- 10 units
- Photoresistor GL5516 Type LDR 10k - 2 units
- Push buttons Omron B3F Blue, Red, White - 3 units
- 100uF / 50V electrolytic capacitor - 5 units
- Active 5V buzzer, continuous sound
- Potentiometer 10K ohm horizontal
- Connector Jack Female Adapter Screw
- Male Jack Connector 9V Battery Adapter

Customers who bought this product also bought

Infrared LED Flame Sensor 5mm

Led infrared sensor.
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm features:
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.

S0132

Price €0.37

40x Female-Female Cable 10cm

40x Female-Female Cable 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont female connectors on both ends
- Compatible with 2.54mm male connectors
- High quality and good working conditions
- Easy to install and use

K1005

Price €1.64

LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable

It has an Atmega32u4 chip running at 16Mhz with a factory-loaded bootloader.
The Leonardo module has all the connectors that the Arduino Leonardo R3 and is compatible with all Arduino shields. LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable features:
- ATmega32u4 microcontroller,
- Operating voltage 5V,
- Power (recommended) 7-12V,
- Digital pins I / O 20 (of which 7 can be used as PWM outputs),
- Analog input pins 12,
- DC current through I / O Pin 40 mA,
- DC current for pin 3.3V 50 mA,
- Flash memory 32 KB (of which 4 KB are used by the bootloader),
- SRAM 2.5 KB,
- EEPROM 1 KB, - Clock speed 16 MHz,
- Interface: UART, USB, SPI, I2C,
- USB communication - Atmega32u4,

B0004

Regular price €9.01 -€2.00 Price €7.01

Micro Servo 9g SG90

Tower Pro Micro Servo 9g SG90 features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

R0013

Regular price €2.22 -€0.20 Price €2.02

LED Display Screen Board Matrix 8x8 Common Cathode/Columns Common Anode Red Dots

LED Display Screen Board Matrix 8x8 Common Cathode/Columns Common Anode Red Dots features:
- Supply voltage of the LED points: 1.8-2.4 VDC
- LED color of the dots: red
- Pin numbers: 16
- Diameter of pins: 0.51mm
- Step between pins: 2.54mm
- Consumption current per segment: 30mA
- Maximum admissible current per segment: 120mA
- Power consumed per segment: 80mW
- Segment numbers (points): 64
- Diameter of a point: 3mm
- Operating temperature: -35 ° C - + 85 ° C
- Storage temperature: -35 ° C - + 85 ° C
- Screen with common cathode connection for the rows and common anode for the columns
- Screen size: 32x32x8 mm

P0125

Regular price €2.39 -€1.00 Price €1.39
€4.95

4,95 tax excl.

1
30+ items
Price €4.95

Order until 4pm we will send today
30 days return