DS18B20 Probe 2m Submersible Temperature Sensor

The DS18B20 is a digital temperature sensor from Dallas Semi Conductors, used to measure ambient temperature or to carry out tests. It supports multipoint readings of the mesh networking type, being able to be deployed in three lines, in order to achieve these readings, it has a built-in pull-up resistance. Dallas Temperature Sensor Module DS18B20 features:
- Operating voltage: 3 - 5.5 VDC
- Measurement operating temperature: -55 ° C - 125 ° C
- Output current: 5 μA
- Accuracy of ± 0.5 ° C between -10 ° C and + 85 ° C
- Storage temperature: -55 ° C - + 125 ° C
- 100% new and high quality
- Module DS18B20 temperature measurement sensor
- The DS18B20 sensor has a pull-up resistor
- Power indicator LED on the module

The UNI-T UT300H temperature meter, which uses the latest technology, enables temperature measurements in the range of 32°C-42.9°C. The high accuracy of the device enables fast and accurate monitoring of body temperature as well as other environmental elements, e.g. objects, food, liquids, etc.

NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance.   Thermistor NTC 1.0K 5% MF52A epoxy resin coating resistor features:

Size: 3mm
Rated resistance: R25 = 1.0k
B value 25/85 = 3950°K
Rated power: ‰¤ 50mW
Tolerance:± 5%
Operating temperature: from -40°C to +125°C  Tinned steel wire 25mm

NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance.   Thermistor NTC 100.0K 5% MF52A epoxy resin coating resistor features:

Size: 3mm
Rated resistance: R25 = 100.0k
B value 25/85 = 3950°K
Rated power: ‰¤ 50mW
Tolerance:± 5%
Operating temperature: from -40°C to +125°C  Tinned steel wire 25mm

Encapsulated with water resistant stainless steel with sensor dimensions 6 * 50mm, cable length 300 cm. DS18B20 Waterproof Digital Temperature Sensor Probe 3m features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 ° C to 125 ° C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
             - Vcc red
             - Yellow digital output
- Inocidable steel
- Cable length: 3m

NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance.   Thermistor NTC 5.0K 5% MF52A epoxy resin coating resistor features:

Size: 3mm
Rated resistance: R25 = 5.0k
B value 25/85 = 3950°K
Rated power: ‰¤ 50mW
Tolerance:± 5%
Operating temperature: from -40°C to +125°C  Tinned steel wire 25mm

Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.
DS18B20 Submersible Probe Sensor Temperature features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Red Vcc
      - Yellow digital output
- Inocidable steel
- Cable length: 1m

Precision Temperature Sensor TO-92 LM335 LM335Z-ST features:
- Power supply from 5 to 30 Vdc
- Connection through analog input
- Temperature range from -40ºC to 100ºC
- Linearity +10 mV / ºK
- Accuracy of measurement: ± 2 ° C
- Manufacturer: Texas Instruments

The GY-906DCI is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, within 15 cm the accuracy is high, approximately 0.5 degrees

Led infrared sensor.
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm features:
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.