Dallas Temperature Sensor Module DS18B20 The DS18B20 is a digital temperature sensor from Dallas Semi Conductors, used to measure ambient temperature or to carry out tests. It supports multipoint readings of the mesh networking type, being able to be deployed in three lines, in order to achieve these readings, it has a built-in pull-up resistance. Dallas Temperature Sensor Module DS18B20 features: - Operating voltage: 3 - 5.5 VDC - Measurement operating temperature: -55 ° C - 125 ° C - Output current: 5 μA - Accuracy of ± 0.5 ° C between -10 ° C and + 85 ° C - Storage temperature: -55 ° C - + 125 ° C - 100% new and high quality - Module DS18B20 temperature measurement sensor - The DS18B20 sensor has a pull-up resistor - Power indicator LED on the module Code S0124 Available Price €1.95
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Available Price €1.99
Potentiometer B10K linear Characteristic: -10k OHM kΩ - linear potentiometer 10k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0067 Available Price €0.99
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.69
40x Male to male cables 20cm Characteristic: -Length: 20cm -Quantity: 40 cables -Mono Dupont connectors on both ends -Compatible with 2.54mm female connectors -High quality and good working condition -Easy to install and use Code K0006 Available Price €2.49
10x Strip 6 Pin Female Short 10x Strip 6 Pin Female Short features: - Pin spacing: 2.54mm - Insert position: Vertical - Insert: Through - Quantity: 10 units of strips of 6 female pins each Code K0143 Available Price €0.18
Resistor 2,2K Ohm 5% 0,25W 1/4W Resistor 2,2K Ohm 5% 0,25W 1/4W features:-2.2K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0015 Available Price €0.08
Rain Sensor Module Water Droplet Detector The module has two outputs: analog A0 and digital D0. digital output D0 - signal 0 or 1 appears depending on the configuration of threshold. The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - digital switching output indicator - Measurements PCB: 3 x 1.5 cm - Sensor measurements: 5.4 x 3.9 cm Code S0022 Available Price €1.69
Pro Micro 5V 16Mhz Arduino Compatible Board It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4 - Operation: 5V - Power (max): 5-12V - Total I / O pins: 20 - PWM pins: 5 - Analog pins: 12 - Maximum current of I / O pins: 40 mA - Maximum current of pin 3.3V: 50 mA - Flash memory: 32 KB (4 KB used by the bootloader) - SRAM: 2.5 KB - EEPROM: 1 KB - Speed: 16 MHz - external interrupt - TWI / I2C, UART, SPI interfaces - Dimensions: 18x33mm - Weight: 30 grams Code B0022 Available Price €9.49
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 Last items in stock Price €25.90
Plate UNO CH340 + Arduino compatible switches It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader. The Uno R3 module has all connectors than the Arduino Uno R3 and is compatible with all Arduino shields. Plate UNO R3 CH340 + Arduino compatible switches features: - ATmega328P chip at 16MHz with crystal external quartz - ATmega328P microprocessor with socket - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6- 20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader -Atmega328 - SRAM 2 KB - Atmega328 Code B0023 ✗ Out-of-Stock Price €10.99
Mega2560 R3 DIY PCB Arduino Mega2560 dimensional motherboard to build a Mega by yourself Code B0014 Available Price €1.79
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €10.90
Kit de Pro Mini Atmega328 5V 16M + Adaptador USB-UART CP2102 para Arduino Set of Pro Mini Atmega328 5V 16M + USB-UART Adapter CP2102 for Arduino Pro mni has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Ideal for connecting TTL RS232 devices to your PC through the USB port. Code B0018 Available Price €12.65
Pro Mini 16MHZ 5V Arduino compatible board - Bootloader Pin Header Compatible 100% ARDUINO - Pro Mini Atmega328P 5v 16Mhz - Miniaturized compatible version of Arduino Pro Mini - It has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can only solder the pins that we need Characteristic: - ATmega328P 16MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 5V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - External interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams Useful links for Arduino /> Code B0019 Last items in stock Price €8.95
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Last items in stock Price €44.95
ATmega2560 R3 REV3 16U2 Mega2560 module with USB cable It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Code B0003 Available Price €24.90
LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable It has an Atmega32u4 chip running at 16Mhz with a factory-loaded bootloader. The Leonardo module has all the connectors that the Arduino Leonardo R3 and is compatible with all Arduino shields. LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable features: - ATmega32u4 microcontroller, - Operating voltage 5V, - Power (recommended) 7-12V, - Digital pins I / O 20 (of which 7 can be used as PWM outputs), - Analog input pins 12, - DC current through I / O Pin 40 mA, - DC current for pin 3.3V 50 mA, - Flash memory 32 KB (of which 4 KB are used by the bootloader), - SRAM 2.5 KB, - EEPROM 1 KB, - Clock speed 16 MHz, - Interface: UART, USB, SPI, I2C, - USB communication - Atmega32u4, Code B0004 Available Regular price €10.90 -€2.00 Price €8.90
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
Mega2560 R3 DIY PCB Arduino Mega2560 dimensional motherboard to build a Mega by yourself Code B0014 Available Price €1.79
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €10.90
Pro Micro 5V 16Mhz Arduino Compatible Board It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4 - Operation: 5V - Power (max): 5-12V - Total I / O pins: 20 - PWM pins: 5 - Analog pins: 12 - Maximum current of I / O pins: 40 mA - Maximum current of pin 3.3V: 50 mA - Flash memory: 32 KB (4 KB used by the bootloader) - SRAM: 2.5 KB - EEPROM: 1 KB - Speed: 16 MHz - external interrupt - TWI / I2C, UART, SPI interfaces - Dimensions: 18x33mm - Weight: 30 grams Code B0022 Available Price €9.49
Kit de Pro Mini Atmega328 5V 16M + Adaptador USB-UART CP2102 para Arduino Set of Pro Mini Atmega328 5V 16M + USB-UART Adapter CP2102 for Arduino Pro mni has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Ideal for connecting TTL RS232 devices to your PC through the USB port. Code B0018 Available Price €12.65
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Last items in stock Price €44.95
Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €8.95
Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €9.99
Pro Mini 16MHZ 5V Arduino compatible board - Bootloader Pin Header Compatible 100% ARDUINO - Pro Mini Atmega328P 5v 16Mhz - Miniaturized compatible version of Arduino Pro Mini - It has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can only solder the pins that we need Characteristic: - ATmega328P 16MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 5V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - External interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams Useful links for Arduino /> Code B0019 Last items in stock Price €8.95