HC-SR04 Ultrasonic Sensor Distance Measuring Module It is very easy to make it work with an Arduino, PIC or any other microcontroller. In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle. HC-SR04 Ultrasonic Sensor Distance Measuring Module features: - Supply voltage: 5V (4.5V- 6V) - Consumption: 30 mA typical, (35 mA max) - Interface: VCC , GND, Signal - Range: 2 cm to 3 meters - Angle 15º - LED indicator of measurement in progress - Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm - Quantity: 1 unit Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry: Automatic robot operation with obstacle detection /> Code S0007 Available Price €1.79
Controller TB6612FNG DC PAP motor TB6612FNG controller, double H-bridge controller driver. Allows to control up to 2 current motors continuous or bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. An improved version of the L298N. H-bridges are made up of MOSFET transistors, rather than BJT transistors as in the L298N. The TB6612FNG has better efficiency and smaller dimensions than the L298N. Controller TB6612FNG DC PAP motor features: - Minimum operating voltage: 4.5 V - Maximum operating voltage: 13.5 V (15V max) - Maximum current: ± 3A per channel (1.2 A direct current per channel) - Logic voltage: 5V Code R0002 Available Price €5.99
M18 Inductive Proximity Sensor M18 Inductive Proximity Sensor features: - Inductive proximity sensor detection switch LJ18A3-8-Z / BX - NPN DC6-36V - A Often used for 3D printer bed leveling - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - NPN NO (Normal Open ) - Detecting distance 8mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C to + 70 ° C (Non-freezing condition) - Head diameter 18 mm - Size 6.9 x 2cm - Cable length 90cm Code S0042 Available Price €3.49
Heat Sink Aluminium Adhesive Radiator 25x25 Heatsink aluminium adhesive radiator for electronics components. Especially recomanded for passive cooling of Stepper Drive, MOSFET, VRM, Vram, IC Chips etc. Good thermal conductivity, reduce the risk of hardware failure due to overheating, made of high quality Aluminum. Code A0118 Available Price €1.19
10m Rigid cable, 22AWG red PVC wire, 0.35mm2 Characteristic: -Conductor: solid wire, tinned copper -Insulation: PVC -Low voltage electrical cables -Rated voltage 300V / 80C -Standard: UL 1007 -Number of conductors: 22AWG, 1x0.35mm2 -Outer diameter: 1.6mm Code K0225 Backorder Price €3.89
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.99
Load Cell 20kg Load cell Load Cell 20kg features: - Load range: 20kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S /°C- Effect of temperature on zero: 0.05% F.S /°C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65- Cable length: 25 cm- Size: 75 x 12.7 x 12.7 mm- Wiring:* Red: Feeding +* Black: Source -* Green: Sign +* White: Signal - Code M0128 Available Regular price €3.19 -€1.00 Price €2.19
Power Adapter 220VAC DC 5V 2.5A EU Plug Micro USB Connector Power Adapter 220VAC DC 5V 2.5A EU Plug Micro USB Connector features: - Input voltage: 100 ~ 240V 50Hz- Output voltage: DC 5V- Output current: 2.5A- DC connector: micro USB- Cable length 85cm Code A0084 Available Price €4.99
Mega2560 R3 DIY PCB Arduino Mega2560 dimensional motherboard to build a Mega by yourself Code B0014 Available Price €1.79
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
DIY UNO R3 PCB DIY UNO R3 PCB features: - PCB board for Arduino UNO R3 DIY Code B0020 Backorder Price €0.98
Pro Micro 5V 16Mhz Arduino Compatible Board It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4 - Operation: 5V - Power (max): 5-12V - Total I / O pins: 20 - PWM pins: 5 - Analog pins: 12 - Maximum current of I / O pins: 40 mA - Maximum current of pin 3.3V: 50 mA - Flash memory: 32 KB (4 KB used by the bootloader) - SRAM: 2.5 KB - EEPROM: 1 KB - Speed: 16 MHz - external interrupt - TWI / I2C, UART, SPI interfaces - Dimensions: 18x33mm - Weight: 30 grams Code B0022 Available Price €9.49
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €10.90
Plate UNO CH340 + Arduino compatible switches It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader. The Uno R3 module has all connectors than the Arduino Uno R3 and is compatible with all Arduino shields. Plate UNO R3 CH340 + Arduino compatible switches features: - ATmega328P chip at 16MHz with crystal external quartz - ATmega328P microprocessor with socket - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6- 20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader -Atmega328 - SRAM 2 KB - Atmega328 Code B0023 ✗ Out-of-Stock Price €10.99
Kit de Pro Mini Atmega328 5V 16M + Adaptador USB-UART CP2102 para Arduino Set of Pro Mini Atmega328 5V 16M + USB-UART Adapter CP2102 for Arduino Pro mni has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Ideal for connecting TTL RS232 devices to your PC through the USB port. Code B0018 Available Price €12.65
Pro Mini 8MHZ 3.3V Arduino compatible board Miniaturized compatible version of Arduino Pro Mini. It has an Atmega328P chip running at 8Mhz with a factory loaded bootloader. It does not include pins so - we can solder only the pins that we need. Pro Mini 8MHZ 3.3V Arduino compatible board features: - ATmega328P 8MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 3.3V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - external interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams An adapter is needed to program it Code B0017 Available Price €8.95
Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Available Price €9.95
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €9.59
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €10.90
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €7.49
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 Last items in stock Price €25.90
ATmega2560 R3 REV3 16U2 Mega2560 module with USB cable It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Code B0003 Available Price €24.90
LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable It has an Atmega32u4 chip running at 16Mhz with a factory-loaded bootloader. The Leonardo module has all the connectors that the Arduino Leonardo R3 and is compatible with all Arduino shields. LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable features: - ATmega32u4 microcontroller, - Operating voltage 5V, - Power (recommended) 7-12V, - Digital pins I / O 20 (of which 7 can be used as PWM outputs), - Analog input pins 12, - DC current through I / O Pin 40 mA, - DC current for pin 3.3V 50 mA, - Flash memory 32 KB (of which 4 KB are used by the bootloader), - SRAM 2.5 KB, - EEPROM 1 KB, - Clock speed 16 MHz, - Interface: UART, USB, SPI, I2C, - USB communication - Atmega32u4, Code B0004 Available Regular price €10.90 -€2.00 Price €8.90
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Available Price €9.95
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €9.59
Gravity: Huskylens - An easy-to-use AI camera | vision sensor Huskylens is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0305) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF013 Available Price €71.49
Pro Mini 8MHZ 3.3V Arduino compatible board Miniaturized compatible version of Arduino Pro Mini. It has an Atmega328P chip running at 8Mhz with a factory loaded bootloader. It does not include pins so - we can solder only the pins that we need. Pro Mini 8MHZ 3.3V Arduino compatible board features: - ATmega328P 8MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 3.3V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - external interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams An adapter is needed to program it Code B0017 Available Price €8.95
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €10.90