Components and sensors

This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards.

The sensors can be integrated into a variety of instruments associated with a concentration of airborne particles to improve equipment, provide timely concentration, and have Exact data.
Present the laser that scatters products on airborne particles, at the same time at a specific angle collect scattered light, changing the intensity curve that scatters over time.
The microprocessor uses the algorithm based on the MIE theory to deduce the grain size contained in the air and the concentration of the particles per unit and quantity. Characteristic: - Power supply: 4.5-5.5 VDC
- Measurement range: 0.3-1.0ï¼ ›1.0-2.5ï¼› 2.5-10 µm (micrometer)
- Accuracy of count: 50%@>

CO2 sensor model MH-Z19C. High precision working voltage 5.0±0.1V DC. The measuring range is between 0 and 5000 ppm. It has a low power consumption. UART and PWM output.

This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards.

This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The  board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board.

This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin.

Air quality sensor with high precision whose SDS011 uses laser dispersion to detect particle concentration between 0.3 and 10 um in the air.

With digital output by USB (UART) and built-in fan. It is a powerful sensor, fast (response less than 10s), accurate and reliable.

A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features:
- USB-Serial TTL 3.3V -5V Converter
- LED indicator for Tx, Rx, power supply
- Communication: Transceiver RX / TX TTL COM Virtual RS232
- Voltage: 3.3V or 5V - via jumper
- Pins: DTR, RX, TX, VCC, CTS, GND
- Protections: Electronic fuse up to 500mA
- Size: 35 x 17 mm Pitch 2,54mm
- Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
User manual for remote control + 4-channel receiver 315 MHz IC2262
- Wire the USB />

This tiny little board features two chips from Maxim Integrated: MAX32664 and MAX30101. The 30101 Oximetry module  is the sensor on board responding for both oximetry and heart rate sesnsing. The MAX32664 is equipped with a Cortex M4 handling algorithimc calculations, digital filtering and automatic gain control. The board comes with I2C and SparkFun has provided to it Qwiic connectors for ease of use.

FTDI FT232RL USB-UART Converter - Mini USB features:
- Serial Converter USB-TTL 3.3V - 5V
- LED indicator of Tx, Rx, power.
- Communication: TTL COM Virtual RS232 RX / TX Transceiver
- Voltage: 3.3V or 5V - per bridge
- Pins: DTR, RX, TX, VCC, CTS, GND
- Protections: Electronic fuse up to 500mA.
- Size: 46 x 19 mm. Step 2.54mm.
- Connection: Mini USB
- Driver: Windows 7 / 8/10 Linux / Mac / Android
- USB TO UART solution with mini USB connector
- FT232RL original on board
- Compatible with Mac, Linux, Android, WinCE, Windows 7/8 / 8.1 / 10 ...
- 3 power mode: 5V output, 3.3V output or powered by the destination board (3.3V-5V)
- 3 LEDs: TXD LED, RXD LED, POWER LED
- Functional pins

Low power CO2 sensor MH-Z1311A, the current consumption is only 150-200uA, waterproof and anti-corrosion, high sensitivity, additionally characterised by excellent linear output. It is very popular used for battery monitors and IAQ devices.

This converter has an internal DC / DC supply and a total isolation between the USB and the RS485 output and allows to establish a reliable and safe communication.
Its FT232RL component has excellent compatibility and a communication rate up to 3M for a maximum distance of 1.2 km. The RS485 output interface uses an optical coupler with high speed for an optical insulation of 1500V and a protection against lightning of 600W: these characteristics allow to protect the computer from the potential damage of static electricity, lightning, over voltages and ground faults. Optical Isolated Converter FT232RL USB 2.0 to RS485 features:
- Required systems: WINDOWS CE / 2000 / XP / VISTA / WIN 7 / LINUX / MAC OS
- Internal DC />

ZPHS01B is an all-in-one air quality module, which integrates laser dust sensor, infrared CO2 sensor, electrochemical formaldehyde, ozone and carbon monoxide sensors, VOC sensor, NO2 sensor, temperature and humidity sensor.

The DFRobot heart rate monitor sensor (SEN0213) is used to measure the electrical activity of the heart.

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

Ideal for connecting TTL RS232 devices to your PC through the USB port. USB to A RS232 UART TTL 5V Converter + Cables features:
- Compatible controller PL2303HX
- 5 pins: 3.3v, 5.0v, TXR, RDX, GND
- Heat shrinkable insulating cover
- LED indicators of data transmission
- 2.5A self-recovery protective fuse
- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux
- Weight: 40 gr. (approx.)

EMG Muscle Signal Sensor Signal Electromyography features:
EMG Muscle signal sensor module kit with 6 disposable electrodes The EMG sensor serves as a bridge to detect small electrical pulses product of
muscle activity and transform them into a signal recognizable by Arduino. NOTE: DO NOT USE THIS SENSOR FOR MEDICAL PURPOSES.
Code Examples: https: //github.com/AdvancerTechnologies/MuscleSensorV3

Ideal to connect TTL RS232 devices to your PC through the USB port. RS232 USB to Serial TTL Adapter Module - USB to Serial PL2303HX PL2303 features:
> - Compatible PL2303 controller
- 5 pins: 3.3V, 5.0V, TxR, RxD, GND
- Heat shrinkable insulating cover
- Led data transmission indicators
- 2.5A self-recovery protector fuse
- Supported OS: Win ME, Win2003, Win XP, Vista, Win 7
- Weight: 40 gr. (approx.)

Photoelectric sensor standard, reliable assurance of 1 million units per year.

· Industry's top class built-in amplifier

· Guaranteed low-temperature operation that can be used in freezing warehouse

· Improvement of coincidence between optical and mechanical axis.

· Protection of sensor even if wiring mistake occurs output reverse protection function is carried (we add diode for reverse connection protection to output line).

CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter features:
- Ideal for connecting TTL RS232 RS485 devices to your PC through the USB port

This fingeprint scanner from ADH-Tech combines a highly precise fingerprint sensor module with an onboard MCU and UART interface enabling trivially very connection to any project.

The scanner independently reads and analyses the fingerprint thanks to an MCU algorithm that can send a converted digital signal to a peripheral serial interface for a data read. The onboard MCU algorithm enables operations such as for example a fingerprint enroll.

Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features:
- CH340 controller
- Supported OS: Win XP, Vista, Win 7.8, OS, Linux
- Work with Modbus, Profibus
- USB 2.0 specification with 6Mbps of maximum speed
- Measures: 60x 18x 14 mm

Mini RS232 to TTL Adapter Max3232 Converter features:
- Converter for RS232 to TTL levels
- MAX3232CSE chip
- Voltage: 3V a 5V
- Speed: no more than 120kbps
- Dimensions: 16x9mm

Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC features:
- Working voltage and TTL levels: 5V
- Size: 44 x 14 mm

This product is widely used in radio modifications, cell phone flash, xbox360 flash detection, GPS, car, Flash, HDD repair, top box upgrade.
It can be used to download MCU types. Module MAX3232 Converter RS232 to TTL Port DB9 female features:
- Input voltage: 3.3 - 5 VDC
- Multi-channel RS232 controller / receiver MAX3232
- Transmission / reception speed up to 250 kbit / s
- DB9 serial port
- Interface with four pins:
       - TX: transmission signal
       - RX: reception signal
       - VCC: Supply voltage
       - GND: connects the power cathode
- Operating temperature: -65 ° C - + 150 ° C
- UART communication
- Includes a 4-wire female / female connector for easy connection with the arduino

The Carbon Monoxide sensor is a low-power digital gas sensor which has a CCS811 sensor and an 8-bit microcontroller, contains an analog-digital converter so that it can detect indoor air quality which can detect monoxide carbon (CO) and a wide range of volatile organic compounds (VOCs). It is a sensor designed to monitor air quality inside personal devices such as mobile devices and smart watches, with low power consumption that can be used with battery

Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1
- LED status indicators - Transmission speed: 5kB / s
- Fuse protector against possible damage to the USB port
- Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux
- Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦
- Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦
- CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦
- AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦

MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime.

With KANDA adapter it is ideal for projects with ARDUINO. Characteristic: - AVR 5V / 3.3V microcontrollers - programming voltage change through jumper JP1
- Status LED indicators
- Transmission speed: 5kB / s
- Protective fuse of possible damage to the USB port
- Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux
- Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦
- Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny € 15 ¦
- CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦
- AT90S2313 series, AT90S2323, AT90S144, AT90S1434 ¦

This module includes the component BME280 that is translated into a digital signal.
The equipment uses the two I2C and SPI interfaces. The BME280 does not allow the module to be used as an altimeter as opposed to its successor BMP280.
Its 5-pin straight connector allows easy connection to other electronic boards. BME280 Digital Temperature Humidity Barometric Pressure Module features:
- Interfaces:
- I2C (up to 3.4 MHz)
- SPI (up to 10 MHz)
- Supply voltage: 1.8-5VDC
- Module operating range:
- Temperature: -40ºC to + 85ºC
- Humidity: 0-100%
- Pressure: 300-1100 hPa
- Resolution of the measures:
- Temperature: 0.01ºC
- Humidity: 0.008%
- Pressure: 0. 18Pa
- Accuracy of the measures:
- Temperature: +/>

Ideal for connecting TTL RS232 devices to your PC through the USB port. PL2303HX PL2303 USB to UART TTL Cable Module RS232 Converter 4 Pin features:
- Compatible controller PL2303HXA
- 4 pins: 5.0V (red), TxR (green), RxD (white), GND (black)
- 2.5A self-recovery protective fuse
- Supported OS: Win8, Win10, WinME, Win2003, Win XP, Vista, Win 7 The 64-bit Prolific drivers provided by Microsoft through Windows Update will not work with most adapters and will therefore generate the generic "Code 10" error.

Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 10m. DS18B20 Digital Temperature Sensor Probe 10m features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Vcc red
      - Yellow digital output
- Inocidable steel
- Cable length: 10m

An RS232 serial port to your PC through the USB port USB 2.0 A Serial Port Cable Adapter DB9 RS232 Series features:
- CH341 driver
- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux, MAC OS9.0/OSX
- High quality, shielded cable
- Power and data in the same cable, does not require more adapters
- Compatible USB interface 1.1 and 2.0
- Support up to 1 mega data transfer
- Length 73cm The adapter allows you to connect a computer with: - Electric meters
- Decoders, programmers
- Cash registers
- Satellite TV
- Control panels
- Mobile phones
- Diagnostic interfaces for cars
- The administration of Cisco routers

3.3V/5V I2C logic level converter module with soldering pins.
Ideal to connect a device that works at 3.3V to one that works with 5V.
It works with digital signals (high and low levels).
Logic Level Converter 3.3 / 5V I2C IIC features:
- Voltage: 3.3V/5V
- Measures: 1.5x 1 cm

Ethanol alcohol sensor module.
MQ gas sensor uses a small indoor heater with an electrochemical sensor.
When the alcohol molecules in the air comply with the electrode the ethanol "changes" into acetic acid and then more current is produced.
MQ-3 Alcohol Sensor Module Ethanol Breathalyzer features:
- Main chip: alcohol sensor MQ-3 and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Detection concentration:
- 0.05mg/L - 10mg/L
- Quick response features:
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

A multiplexer of this type actually only acts as a switch 16 to a 1.
The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".
The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features:
- Based on chip CD74HC4067
- Analog signal input: Y0-Y15, 16 channels
- Analog signal output: Z pin
- Digital input, channel control: S0-S3
- Module size: approx. 4 x 1.8cm
- Package includes:
* 1 x CD74HC4067 MUX connection module
* 2 x row of soldering pins

This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.
The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.
The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB).

Connecting a 3.3V device to a 5V system is a challenge.
The bidirectional logic level converter is a small device that safely drops the signals from 5V to 3.3V and increases 3.3V to 5V at the same time.
This level converter also works with 2.8V and 1.8V devices. What really separates this logic level converter from our previous versions is that it can successfully set its high and low voltages and go up and down between them safely on the same channel.
Each level converter has the ability to convert 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. The level converter is very easy to use. The board needs to be powered from the two sources of voltage (high voltage and low voltage) that your system is using.

Characteristic: - Supply voltage: 4.5V- 5.5V
- Consumption: 30 mA typical
- Analog output
- Range: 10cm to 80cm
- Dimensions: 29x12mm
- Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino

This bidirectional logic level converter can be used with normal series, I2C, SPI and other digital signals. It does not work with an analog signal.
It is very easy to use. The card must be powered from the two voltages (high and low voltage) used by the system.
A high voltage (5 V for example) to the pin "HV", low voltage (3.3 V for example) in "LV", and the system ground to pin "GND". TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level features:
- 2 high voltage channels and low voltage logic logic for bidirectional translation
- 2 low voltage channels High voltage high voltage logic in unidirectional conversion
- The board module is compatible, it can be inserted directly in the use test panel
- HV to 5 V power

TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.
Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features:
- Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument
- VCCA power supply voltage: 4.5 - 5.5 VDC
- VCCB power supply voltage: 2.7 - 3.6 VDC
- Low level input voltage V (IL): 0.8 V
- High-level input voltage V (IH): 2 V
- Low level output current I (OL): 12 - 24 mA
- High level output current I (OH): -24 - -12 mA
- 8 channels allow the conversion of the IO communication level
- Channel levels A and B are controlled by VCCA and VCCB

The Arduino turbidity sensor SEN0189  detects water quality by measuring turbidity levels. It can detect suspended particles in water by measuring the light transmittance and the scattering coefficient, which changes with the amount of total suspended solids (TTS) in the water.

Gravity: SHT1x Temperature & Humidity Sensor (DFR0066) Accurate, durable, highly compatible and easy to use, it has all the attributes that a superior temperature and humidity sensor requires.

The PCF8591 is a low-power 8-bit single-chip, single-chip, 8-bit data acquisition device with four analog inputs, an analog output, and an I2C serial bus interface.
Three address legs A0, A1 and A2 are used to program the hardware address, allowing the use of up to eight devices connected to the I2C bus without additional hardware.
Address, control and data to and from the device are transferred in series through the two-way bidirectional I2C bus. Analogue to Digital Converter PCF8591T features:
- Main chip: PCF85911
- Operating voltage supply: 2.5 - 6 V
- Low standby current
- Serial input / output through the I2C bus
- 3 hardware address pins A0, A1, A2
- Sampling speed given by the I2C bus speed

MS01 works with SONOFF TH10/16 to accurately measure soil moisture and send data to your mobile phone. MS01 can regularly water and check soil moisture anytime and anywhere to make your flowers grow healthier. This is an accessory used in SONOFF TH10 / TH16.

6-pin/10-pin Kanda DIL adapter features:
- Connector for Usbasp Programmer AVR Atmega8 Atmega128

This is a CH340G TTL UART 5V serial adapter, designed to allow adding a USB connection to your project.
In addition, this opens up the possibility of programming microcontrollers like the Arduino Pro mini.
This module allows you to connect your project, from programming small microcontrollers to a custom computer keyboard.
The module is ready for use of a UART connection.
This may require the installation of a driver; however, it is a standard driver distributed by Microsoft Windows Update, available in Linux and that can be configured in MAC OS.
Adapter module CH340G LC Technology -TTL UART 5V series features:
- Manufacturer: LC Technology,
- Communication chipset: CH340G
- Communication: UART,
- Pin connection:

Inductive Proximity Sensor PL-05N NPN Limit Switch is used for controlling machinery as part of a control system, as a safety interlock, or to count objects passing a point. Inductive proximity sensor PL-05N 5mm with NPN output features:
- Manufacturer: Fotek,
- Square Type,
- Sensing distance: 5mm,
- Operating voltage: 10 - 30 VDC,
- Response frequency: 800Hz,
- Output method: NPN, 150mA load,
- Hysteresis: <10% of sensing distance,
- Protection degree: IP67,
- Working temperature/Hum: -20ºC - +80ºC, 35% - 90% RH,
- Body dimension: 30.5x17.9x10.2mm (LxWxH),
- Mounting Method: Flush,
- Sensing Direction: Horizontal,
- Materia Housing: High-impact plastic,
- Screw hole: 3.2mm, Pitch: 10.5mm,

The BME280 is an environmental sensor (SEN0236) integrating a temperature sensor, a humidity sensor and a barometer. Powered from 3.3 V to 5 V with I2C and SPI interface. Measuring range: temperature: -40 °C to 85 °C, humidity: 0 %RH to 100 %RH, pressure: 300 hPa to 1100 hPa.

Descripción:
El adaptador de HDMI a VGA le permite conectar un monitor, proyector o LCD analógico estándar que usa un conector o cable VGA a un cuaderno, DVD, TVbox, reproductor BIU-rog, computadora, proyector.
Característica:
- Tipo: adaptador/convertidor AV,
- Conector A: HDMI macho,
- Conector B: VGA hembra,
- Conexión Split / Duplicación: ninguna (1: 1),
- El adaptador dispone de una entrada audio Jack hembra,
- Ancho del cable del adaptador: 15cm,
- Incluye un cable audio Jack macho de ambos lados,
- Ancho del cable audio: 52cm,
- Color: blanco.

Standard ISP download port, for on-line programming. Built-in crystal oscillator circuit (8MHz), crystal are replaceable. Has reset push button, power reset push button. 

Level sensor for liquids with float. The liquid level sensor acts as a switch. Liquid level float sensors are used when constant control and regulation of the liquid level (water, oil and other fluids) is required such as extraction pumps. The sensor is equipped with a float with a magnet which, acting by the buoyancy force of the fluid, moves along the tube, shortening or opening the reed switch. It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where the level of non-corrosive liquids such as water tanks or aquariums needs to be monitored. It is made of stainless steel.

The GY-906DCI is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, within 15 cm the accuracy is high, approximately 0.5 degrees

This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.
Your converter has four analog inputs, one analog output and one I2C serial bus interface.
It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.
The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.
It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features:
- Supply voltage (between VSS and VDD): 2.5-6VDC

The sensor measures the current flowing in the cable without cutting it. The measurement is made on a single insulated wire, the output is an analog voltage from 0 to 1 V. Sensor SCT-013-050, Non-Invasive 50A AC Current Meter

A standard IEEE1284 DB25 parallel port to your PC via the USB port. Transmission speed reaches 12 Mbps. This cable is "USB Printing Support" port and not Parallel "LPT Printer Port" 

M18 Inductive Proximity Sensor features:
- Inductive proximity sensor detection switch LJ18A3-8-Z / BX
- NPN DC6-36V
- A Often used for 3D printer bed leveling
- Cylindrical cable type DC 3 cable type (black, brown, blue)
- Inductive sensor type
- NPN NO (Normal Open )
- Detecting distance 8mm
- DC supply voltage 6-36V
- Current output 300mA
- Response frequency 0.5KHz
- Detects iron / aluminum - Operating temperature -25 ° C to + 70 ° C (Non-freezing condition)
- Head diameter 18 mm
- Size 6.9 x 2cm
- Cable length 90cm

Ideal for projects with ARDUINO, Smart Car
Detects transparent and translucent obstacles
E18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car features:
- Current consumption: up to 100 mA
- Supply voltage 5V
- Current consumption <25mA
- Response time of 2 ms
- Measured distance: 3-80cm 15st angle
- Screw to adjust the sensitivity, the back
- Output status led indicator
- Operating temperature: -25°C - + 55°C
- Material: high-strength plastic
- Type of output: normally open, NPN
- Dimensions: 18 mm in diameter, Length 45 mm
- Cable length 55cm
- Departures:
      - Brown: +
      - Blue: -
      - Black: OUT

The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden.

Sensor Module ML8511 UV features:
- The module converts the photocurrent into voltage to detect UV intensity
- The analog voltage is proportional to UV light detecting
- The has a power saving mode of up to 0.1uA, suitable for smart portable devices or mobile phones for use
- Power supply: 5V
- Analog output
- Captured wavelength: 280-390nm
- Ultra low power consumption
- Meteorological applications, skincare, industrial UV level measurement
- Dimensions of PCB: 30x22mm

The ZP07-MP503 air quality module offers high sensitivity with low power consumption and long life. Calibration before shipment from 10 seconds to 3 minutes max. with automatic warm-up function. Automatic fault check.