Fiberflex 30D Flexible Filament 1.75mm 0.85kg Black color Premium Bobina para Impresora 3D Code I0423 Backorder Regular price €38.60 -20% Price €30.88
Thermal tape 20mm type Kapton Characteristic: - Supports up to 280ºC - Electrical and antistatic insulation - Resistant to acidic products and alkaline - Solvent resistant - Adhesive - Length Approx: 26m Code I0053 Available Price €4.85
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 ✗ Out-of-Stock Price €6.99
16 Channel Relay Module 12V 10A This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL, PLC output).16 Channel Relay Module 12V 10A AVR features:- Channels: 16 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 3mA- Insulation: Yes- Low shot: 0-2V- LED indicator: For each channel- Dimensions: 18x 9x 2cm Code RL009 Available Price €15.49
Reed Switch Module Magnetic Foil Sensor This Reed switch module uses a small device called a reed switch. When the device is exposed to a magnetic field, the two ferrous materials inside the switch come together and the switch closes. When the magnetic field is removed the switch opens. The operating mode: - When exposed to a magnetic field the DO output is high - Power supply: 3.3-5V - Contact type: SPST-NO (normally open) - Use temperature: -20ºC to + 80ºC - Type Output: Digital (1 - 0) - PCB dimensions: 32 x 14 mm Code S0045 Available Price €1.39
Raspberry Pi Pico GPIO Expansion Board The Raspberry Pi Pico GPIO Expansion Board is an advanced product with a 3.3V output voltage that allows you to easily work on the GPIO pins of your Pico, via two ways (male and female header). Ideal for using both male and female jumpers/bridge cables. Code RA125 Available Price €8.95
ATmega2560 R3 REV3 16U2 Mega2560 module with USB cable It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Code B0003 Available Price €24.90
Rechargeable Battery Samsung ICR18650 2600mAh Li-ion Characteristic: - Lithium Battery WITHOUT Protection - Nominal capacity: 2600mAh (discharge of 0.2C, 2.75V) - Minimum capacity: 2550mAh (0.2C, 2.75V discharge) - Charging voltage: 4.2 ± 0.05 V - Nominal voltage: 3.63V - Charging method: DC-CV (constant voltage with current limited) - Charging current: standard charge: 1300mA, fast charge: 2600mA - Charging time: standard charge: 3 hours, fast charge: 2.5 hours - Max. Charging current: 2600mA (ambient temperature 25 °) - Max. Discharge current: 5200mA (ambient temperature 25 °) - Discharge cut-off voltage: 2.75V - Cell weight: 47.0g maximum - Cell dimension: Height: 65.00 mm max., Diameter: 18.40 mm max. Code PP018 ✗ Out-of-Stock Price €5.99
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Backorder Price €5.95
RS232 USB to Serial TTL Adapter Module - USB to Serial PL2303HX PL2303 Ideal to connect TTL RS232 devices to your PC through the USB port. RS232 USB to Serial TTL Adapter Module - USB to Serial PL2303HX PL2303 features: > - Compatible PL2303 controller - 5 pins: 3.3V, 5.0V, TxR, RxD, GND - Heat shrinkable insulating cover - Led data transmission indicators - 2.5A self-recovery protector fuse - Supported OS: Win ME, Win2003, Win XP, Vista, Win 7 - Weight: 40 gr. (approx.) Code C0005 Available Price €1.49
USB 2.0 to Parallel Adapter Cable DB25 Interface IEEE 1284 Printer A standard IEEE1284 DB25 parallel port to your PC via the USB port. Transmission speed reaches 12 Mbps. This cable is "USB Printing Support" port and not Parallel "LPT Printer Port" Code C0020 Available Price €2.99
Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.Your converter has four analog inputs, one analog output and one I2C serial bus interface.It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features: - Supply voltage (between VSS and VDD): 2.5-6VDC Code M0133 Available Price €2.46
Module MAX3232 Converter RS232 to TTL Port DB9 female This product is widely used in radio modifications, cell phone flash, xbox360 flash detection, GPS, car, Flash, HDD repair, top box upgrade.It can be used to download MCU types. Module MAX3232 Converter RS232 to TTL Port DB9 female features: - Input voltage: 3.3 - 5 VDC- Multi-channel RS232 controller / receiver MAX3232- Transmission / reception speed up to 250 kbit / s- DB9 serial port- Interface with four pins: - TX: transmission signal - RX: reception signal - VCC: Supply voltage - GND: connects the power cathode- Operating temperature: -65 ° C - + 150 ° C- UART communication- Includes a 4-wire female / female connector for easy connection with the arduino Code C0016 Available Price €2.90
USB to RS485 USB to 485 Max485 Converter Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features: - CH340 controller- Supported OS: Win XP, Vista, Win 7.8, OS, Linux- Work with Modbus, Profibus- USB 2.0 specification with 6Mbps of maximum speed- Measures: 60x 18x 14 mm Code C0003 Available Price €2.69
CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter features: - Ideal for connecting TTL RS232 RS485 devices to your PC through the USB port Code C0011 Available Price €7.95
FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features: - USB-Serial TTL 3.3V -5V Converter - LED indicator for Tx, Rx, power supply - Communication: Transceiver RX / TX TTL COM Virtual RS232 - Voltage: 3.3V or 5V - via jumper - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA - Size: 35 x 17 mm Pitch 2,54mm - Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for remote control + 4-channel receiver 315 MHz IC2262 - Wire the USB /> Code C0007 Available Price €3.95
SparkFun FTDI Basic Breakout - 3.3V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP024 Available Price €19.99
Analogue to Digital Converter PCF8591T The PCF8591 is a low-power 8-bit single-chip, single-chip, 8-bit data acquisition device with four analog inputs, an analog output, and an I2C serial bus interface.Three address legs A0, A1 and A2 are used to program the hardware address, allowing the use of up to eight devices connected to the I2C bus without additional hardware.Address, control and data to and from the device are transferred in series through the two-way bidirectional I2C bus. Analogue to Digital Converter PCF8591T features: - Main chip: PCF85911- Operating voltage supply: 2.5 - 6 V- Low standby current- Serial input / output through the I2C bus- 3 hardware address pins A0, A1, A2- Sampling speed given by the I2C bus speed Code C0018 Available Price €2.50
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Backorder Price €5.95
RS232 USB to Serial TTL Adapter Module - USB to Serial PL2303HX PL2303 Ideal to connect TTL RS232 devices to your PC through the USB port. RS232 USB to Serial TTL Adapter Module - USB to Serial PL2303HX PL2303 features: > - Compatible PL2303 controller - 5 pins: 3.3V, 5.0V, TxR, RxD, GND - Heat shrinkable insulating cover - Led data transmission indicators - 2.5A self-recovery protector fuse - Supported OS: Win ME, Win2003, Win XP, Vista, Win 7 - Weight: 40 gr. (approx.) Code C0005 Available Price €1.49
USB 2.0 to Parallel Adapter Cable DB25 Interface IEEE 1284 Printer A standard IEEE1284 DB25 parallel port to your PC via the USB port. Transmission speed reaches 12 Mbps. This cable is "USB Printing Support" port and not Parallel "LPT Printer Port" Code C0020 Available Price €2.99
Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.Your converter has four analog inputs, one analog output and one I2C serial bus interface.It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features: - Supply voltage (between VSS and VDD): 2.5-6VDC Code M0133 Available Price €2.46
Module MAX3232 Converter RS232 to TTL Port DB9 female This product is widely used in radio modifications, cell phone flash, xbox360 flash detection, GPS, car, Flash, HDD repair, top box upgrade.It can be used to download MCU types. Module MAX3232 Converter RS232 to TTL Port DB9 female features: - Input voltage: 3.3 - 5 VDC- Multi-channel RS232 controller / receiver MAX3232- Transmission / reception speed up to 250 kbit / s- DB9 serial port- Interface with four pins: - TX: transmission signal - RX: reception signal - VCC: Supply voltage - GND: connects the power cathode- Operating temperature: -65 ° C - + 150 ° C- UART communication- Includes a 4-wire female / female connector for easy connection with the arduino Code C0016 Available Price €2.90
USB to RS485 USB to 485 Max485 Converter Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features: - CH340 controller- Supported OS: Win XP, Vista, Win 7.8, OS, Linux- Work with Modbus, Profibus- USB 2.0 specification with 6Mbps of maximum speed- Measures: 60x 18x 14 mm Code C0003 Available Price €2.69
CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter features: - Ideal for connecting TTL RS232 RS485 devices to your PC through the USB port Code C0011 Available Price €7.95
FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features: - USB-Serial TTL 3.3V -5V Converter - LED indicator for Tx, Rx, power supply - Communication: Transceiver RX / TX TTL COM Virtual RS232 - Voltage: 3.3V or 5V - via jumper - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA - Size: 35 x 17 mm Pitch 2,54mm - Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for remote control + 4-channel receiver 315 MHz IC2262 - Wire the USB /> Code C0007 Available Price €3.95
SparkFun FTDI Basic Breakout - 3.3V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP024 Available Price €19.99
Analogue to Digital Converter PCF8591T The PCF8591 is a low-power 8-bit single-chip, single-chip, 8-bit data acquisition device with four analog inputs, an analog output, and an I2C serial bus interface.Three address legs A0, A1 and A2 are used to program the hardware address, allowing the use of up to eight devices connected to the I2C bus without additional hardware.Address, control and data to and from the device are transferred in series through the two-way bidirectional I2C bus. Analogue to Digital Converter PCF8591T features: - Main chip: PCF85911- Operating voltage supply: 2.5 - 6 V- Low standby current- Serial input / output through the I2C bus- 3 hardware address pins A0, A1, A2- Sampling speed given by the I2C bus speed Code C0018 Available Price €2.50