PL2303HX PL2303 USB to UART TTL Cable Module RS232 Converter 4 Pin

An RS232 serial port to your PC through the USB port USB 2.0 A Serial Port Cable Adapter DB9 RS232 Series features:
- CH341 driver
- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux, MAC OS9.0/OSX
- High quality, shielded cable
- Power and data in the same cable, does not require more adapters
- Compatible USB interface 1.1 and 2.0
- Support up to 1 mega data transfer
- Length 73cm The adapter allows you to connect a computer with: - Electric meters
- Decoders, programmers
- Cash registers
- Satellite TV
- Control panels
- Mobile phones
- Diagnostic interfaces for cars
- The administration of Cisco routers

This converter has an internal DC / DC supply and a total isolation between the USB and the RS485 output and allows to establish a reliable and safe communication.
Its FT232RL component has excellent compatibility and a communication rate up to 3M for a maximum distance of 1.2 km. The RS485 output interface uses an optical coupler with high speed for an optical insulation of 1500V and a protection against lightning of 600W: these characteristics allow to protect the computer from the potential damage of static electricity, lightning, over voltages and ground faults. Optical Isolated Converter FT232RL USB 2.0 to RS485 features:
- Required systems: WINDOWS CE / 2000 / XP / VISTA / WIN 7 / LINUX / MAC OS
- Internal DC />

Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC features:
- Working voltage and TTL levels: 5V
- Size: 44 x 14 mm

A standard IEEE1284 DB25 parallel port to your PC via the USB port. Transmission speed reaches 12 Mbps. This cable is "USB Printing Support" port and not Parallel "LPT Printer Port" 

The PCF8591 is a low-power 8-bit single-chip, single-chip, 8-bit data acquisition device with four analog inputs, an analog output, and an I2C serial bus interface.
Three address legs A0, A1 and A2 are used to program the hardware address, allowing the use of up to eight devices connected to the I2C bus without additional hardware.
Address, control and data to and from the device are transferred in series through the two-way bidirectional I2C bus. Analogue to Digital Converter PCF8591T features:
- Main chip: PCF85911
- Operating voltage supply: 2.5 - 6 V
- Low standby current
- Serial input / output through the I2C bus
- 3 hardware address pins A0, A1, A2
- Sampling speed given by the I2C bus speed

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features:
- USB-Serial TTL 3.3V -5V Converter
- LED indicator for Tx, Rx, power supply
- Communication: Transceiver RX / TX TTL COM Virtual RS232
- Voltage: 3.3V or 5V - via jumper
- Pins: DTR, RX, TX, VCC, CTS, GND
- Protections: Electronic fuse up to 500mA
- Size: 35 x 17 mm Pitch 2,54mm
- Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
User manual for remote control + 4-channel receiver 315 MHz IC2262
- Wire the USB />

FTDI FT232RL USB-UART Converter - Mini USB features:
- Serial Converter USB-TTL 3.3V - 5V
- LED indicator of Tx, Rx, power.
- Communication: TTL COM Virtual RS232 RX / TX Transceiver
- Voltage: 3.3V or 5V - per bridge
- Pins: DTR, RX, TX, VCC, CTS, GND
- Protections: Electronic fuse up to 500mA.
- Size: 46 x 19 mm. Step 2.54mm.
- Connection: Mini USB
- Driver: Windows 7 / 8/10 Linux / Mac / Android
- USB TO UART solution with mini USB connector
- FT232RL original on board
- Compatible with Mac, Linux, Android, WinCE, Windows 7/8 / 8.1 / 10 ...
- 3 power mode: 5V output, 3.3V output or powered by the destination board (3.3V-5V)
- 3 LEDs: TXD LED, RXD LED, POWER LED
- Functional pins

3.3V/5V I2C logic level converter module with soldering pins.
Ideal to connect a device that works at 3.3V to one that works with 5V.
It works with digital signals (high and low levels).
Logic Level Converter 3.3 / 5V I2C IIC features:
- Voltage: 3.3V/5V
- Measures: 1.5x 1 cm

This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The  board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board.

This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin.