USBASP AVR ATmega8 ATmega128 Programmer Kanda Adapter Cable

CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter features:
- Ideal for connecting TTL RS232 RS485 devices to your PC through the USB port

3.3V/5V I2C logic level converter module with soldering pins.
Ideal to connect a device that works at 3.3V to one that works with 5V.
It works with digital signals (high and low levels).
Logic Level Converter 3.3 / 5V I2C IIC features:
- Voltage: 3.3V/5V
- Measures: 1.5x 1 cm

Connecting a 3.3V device to a 5V system is a challenge.
The bidirectional logic level converter is a small device that safely drops the signals from 5V to 3.3V and increases 3.3V to 5V at the same time.
This level converter also works with 2.8V and 1.8V devices. What really separates this logic level converter from our previous versions is that it can successfully set its high and low voltages and go up and down between them safely on the same channel.
Each level converter has the ability to convert 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. The level converter is very easy to use. The board needs to be powered from the two sources of voltage (high voltage and low voltage) that your system is using.

The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden.

TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.
Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features:
- Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument
- VCCA power supply voltage: 4.5 - 5.5 VDC
- VCCB power supply voltage: 2.7 - 3.6 VDC
- Low level input voltage V (IL): 0.8 V
- High-level input voltage V (IH): 2 V
- Low level output current I (OL): 12 - 24 mA
- High level output current I (OH): -24 - -12 mA
- 8 channels allow the conversion of the IO communication level
- Channel levels A and B are controlled by VCCA and VCCB

Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC features:
- Working voltage and TTL levels: 5V
- Size: 44 x 14 mm

A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features:
- USB-Serial TTL 3.3V -5V Converter
- LED indicator for Tx, Rx, power supply
- Communication: Transceiver RX / TX TTL COM Virtual RS232
- Voltage: 3.3V or 5V - via jumper
- Pins: DTR, RX, TX, VCC, CTS, GND
- Protections: Electronic fuse up to 500mA
- Size: 35 x 17 mm Pitch 2,54mm
- Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
User manual for remote control + 4-channel receiver 315 MHz IC2262
- Wire the USB />

The PCF8591 is a low-power 8-bit single-chip, single-chip, 8-bit data acquisition device with four analog inputs, an analog output, and an I2C serial bus interface.
Three address legs A0, A1 and A2 are used to program the hardware address, allowing the use of up to eight devices connected to the I2C bus without additional hardware.
Address, control and data to and from the device are transferred in series through the two-way bidirectional I2C bus. Analogue to Digital Converter PCF8591T features:
- Main chip: PCF85911
- Operating voltage supply: 2.5 - 6 V
- Low standby current
- Serial input / output through the I2C bus
- 3 hardware address pins A0, A1, A2
- Sampling speed given by the I2C bus speed

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

This is a CH340G TTL UART 5V serial adapter, designed to allow adding a USB connection to your project.
In addition, this opens up the possibility of programming microcontrollers like the Arduino Pro mini.
This module allows you to connect your project, from programming small microcontrollers to a custom computer keyboard.
The module is ready for use of a UART connection.
This may require the installation of a driver; however, it is a standard driver distributed by Microsoft Windows Update, available in Linux and that can be configured in MAC OS.
Adapter module CH340G LC Technology -TTL UART 5V series features:
- Manufacturer: LC Technology,
- Communication chipset: CH340G
- Communication: UART,
- Pin connection: