TDA2030A 1X18W Audio Amplifier

Classic development board designed and manufactured by Heltec Automation (TM), based on the ESP32-S3FN8 + SX1262. Integrates Wi-Fi, Bluetooth, lithium battery management system, dot matrix OLED screen, USB-C interface. Compatible with Arduino IDE, Micro Python, Platform.io, Espressif IDE. Our module is supplied with Lora antenna and IPEX adapter (U.FL) and header pins.

- WIFI module based on the ESP8266 controller
- ESP8266-12F is an improved version of ESP8266-12E
- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated
ESP-12F ESP8266 12F WiFi Board Module features:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP Stack.
- PLL, regulators and integrated energy management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low energy mode: <10 uA
- Integrated 32-bit processor

SIM808 GPRS GSM GPS Bluetooth SIM Quadband features:
- SIM card SIM808 GPRS GSM GPS Bluetooth SIM
- Supply voltage range: 3.4-4.4V
- Four bands GSM 850/900/1800 / 1900MHz
- GPRS multi-slot class 12/10
- GPRS mobile station class B
- According to GSM phase 2/2 +
- Class 4 (2 W at 850/900 MHz)
- Class 1 (1W at 1800 / 1900MHz)
- Control by AT commands (3GPP TS 27.007.27.005 and enhanced AT Commands from SIM Com)
- Operating temperature: -40 to + 85 ° C
- PCB dimension: 38x38mm
- GPS sensitivity
- Tracking: -165dBm Cold start Sensitivity
- Cold start: -147dBm
- Time to first solution
- Cold start: 30 s
- Start to warm up: 28s
- Already hot: 1s - Accuracy

ESP32-WROOM-32E (ESP32-DEVKITC-32E) is an evaluation board with ESP32 processor, 4MB FLASH, 802.11 a/b/g/n (Wi-Fi, WiFi, WLAN) and BlueTooth® Smart Ready 4.x dual-mode. It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use.

This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.
The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.
This is a significant improvement over the CC1100 module.
It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.
Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @>

This LED power amplifier with a Sonoff power adapter is designed to extend existing Sonoff LED lighting systems. With this signal amplifier, you have the option to extend your Sonoff LED strip system, as the included power adapter provides sufficient power.

Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features:

Specifications of the emitter module: - Power supply: 3V ~ 12V
- Working intensity: max = 40mA (at 12V), min = 9mA (at 3V)
- AM ASK / OOK modulation
- SAW filter
- Working frequency: 315MHz-433.92MHz
- Transmission power: 25mW (315MHz at 12V)
- Range: 20 to 200 meters (different voltages can give different results)
- Transfer speed: 4 kB / S
- Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V
- Work intensity: 5.5mA (at 5.0VDC)
- Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm

It is a mini GPS module including a NEO-6M chip and an EEPROM memory chip.
The SMA antenna port is On-board IPEX and cell phone button battery ensure robust positioning efficiency and fast satellite discovery speed.
Serial port provides simple initial knowledge to stay in touch with the most compatible Arduino-compatible MCU STM32. Characteristic: - Supply voltage: 3.3 - 5 VDC
- Operating current: 45 mA
- Communication speed: 9600 Bauds configurable from 4800 to 115200 Bauds
- Navigation update: 5 Hz max. (1 Hz default)
- Capture time: at the beginning 27s, in operation 1s
- Operating temperature: -40 ° C - + 85 ° C
- separate GPS antenna 18x18 mm - Size: 22x30x13 mm

WS2812 RGB 5050 Smart Addressable 5V Arduino LED WS2811 features:
- WS2812 are LEDs that have built-in logic, making it possible to vary the color of each LED individually
- WS2812 includes an integrated inside each LED, which allows access to each pixel individually. For this reason, these types of LEDs are individually indexable.
- They are based on the 5050 LED
- 24-bit color control (8-bit PWM per channel)
- 16.8 millions of colors per LED
- One-wire communication
- Power: max. 5 Vdc
- Current: 18.5mA
- Input and output terminals (data and power)

2 meter LED strip easily installed for use with Sonoff controllers via WiFi and RF. Great lights to create any ambience in any room. Change their colour and rhythm from your mobile or controller. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. (Controller and adapter not included)