Arduino Uno R3 Arduino UNO is the best board to start your experience with electronics and programming. If this is your first experience with the platform, UNO is the most robust board you can start with. UNO is the most widely used and documented board in the entire Arduino family. Its power ensures ATmega 328p microcontroller, the board is equipped with 14 digital pins, and 6 analog Code BAR66 Available Price €23.99
Current Sensor ACS712 AC/DC 30A for Arduino Sensor used to measure the current in the circuit to which it is connected. Characteristic: - Output: Analog - Power: 5V - Accuracy: 1.5% - Measuring capacity: +/- 30A - Dimensions: 31 x 13 mm Code M0028 Available Price €3.39
PMS5003 High Accuracy Particle Concentration Sensor The sensors can be integrated into a variety of instruments associated with a concentration of airborne particles to improve equipment, provide timely concentration, and have Exact data. Present the laser that scatters products on airborne particles, at the same time at a specific angle collect scattered light, changing the intensity curve that scatters over time. The microprocessor uses the algorithm based on the MIE theory to deduce the grain size contained in the air and the concentration of the particles per unit and quantity. Characteristic: - Power supply: 4.5-5.5 VDC - Measurement range: 0.3-1.0ï¼ ›1.0-2.5ï¼› 2.5-10 µm (micrometer) - Accuracy of count: 50%@> Code S0046 Available Price €27.90
NDIR CO2 Sensor MH-Z14A Carbon dioxide detection MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime. Code S0149 Available Regular price €29.95 -€6.00 Price €23.95
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.95
Sonoff DR - Sonoff DIN Rail Tray Most Sonoff products are not DIN-rail mounted, making it difficult to place Sonoff products in the switchboard or control panel. With this simple tray you can place your switches inside the home's entrance box, for easy installation. Code WS029 Available Price €2.89
DC voltage sensor 0-25v for Arduino Voltage Sensor Module 0.02445V ~ 25V. When the module is powered by 5V voltage detection It does not exceed 25V, and when the module is powered with 3.3V the voltage detection does not exceed 16.5V. 100% Compatible with Arduino. DC voltage sensor 0-25v for Arduino features: - Input voltage: 0-25 VDC - Voltage detection range: 0.02445V-25 VDC - Analog voltage resolution: 0.00489 V - DC input connector: cathode terminal connected to VCC, GND negative pole - Output interface: "+" then 5 / 3.3V, "-" then GND, "s" then the Arduino AD pins Code M0191 Available Price €1.59
XL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 Descripción:Chip XL4015 - Upgrade of the LM2596Drop moduleUse a multimeter to check the output voltage and adjust the potentiometerVoltage controlXL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 features:- Input voltage: 4.5V-38V- Output voltage: 1.25-36.5V- Current output: 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0012 Available Price €4.95
NDIR CO2 Sensor MH-Z14A Carbon dioxide detection MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime. Code S0149 Available Regular price €29.95 -€6.00 Price €23.95
MQ-135 Air Quality Sensor High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases. The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it. MQ-135 Air Quality Sensor features:- Main chip: MQ-135 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 10ppm - 300ppm NH3 10ppm - 1000ppm Benzene 10ppm - 300ppm Alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0034 Available Price €2.45
Dust Sensor Module PPD42NS PM2.5 This module is a dust sensor capable of detecting more than one micron of dust particles. It has two types of output: output of 4V high-level signal for a clean environment and 0.7V low-level signal for a particle-laden environment. Its power supply is 5VDC and the particle detection range is maximum at 8000 units per 283ml. Dust Sensor Module PPD42NS PM2.5 features: - Supply voltage: 5VDC - Working current: 90mA - Sensitivity: 0.5V / ( 0.1 mg / m3) - Particle detection minimum value: 1 micron - Output mode: Hi = 4V impulses (clean environment); Lo = 0.7V (charged environment) - Temperature working: 0-45 ° C - Working humidity: 0-90% RH - PCB size: 59x45x22 mm Code S0123 Available Regular price €11.89 -€2.00 Price €9.89
MH-Z1311A low-power consumption NDIR CO2 sensor Low power CO2 sensor MH-Z1311A, the current consumption is only 150-200uA, waterproof and anti-corrosion, high sensitivity, additionally characterised by excellent linear output. It is very popular used for battery monitors and IAQ devices. Code S0158 Available Price €29.49
Air Monitoring HAT for Raspberry Pi This HAT is an open source portable sensor that provides the level of suspended particulate matter quantity with its mass. It has a powerful and high-tech PMSA003 sensor that provides the information of suspended particulate matter (PM1.0, PM2.5, PM10) in the air per unit volume. Code RA127 ✗ Out-of-Stock Price €56.90
Air quality sensor ZP07-MP503 Gas detection The ZP07-MP503 air quality module offers high sensitivity with low power consumption and long life. Calibration before shipment from 10 seconds to 3 minutes max. with automatic warm-up function. Automatic fault check. Code S0150 Available Price €5.45
MH-Z19C Infrared Sensor module 5000ppm CO2 monitor HVAC PWM output UART CO2 sensor model MH-Z19C. High precision working voltage 5.0±0.1V DC. The measuring range is between 0 and 5000 ppm. It has a low power consumption. UART and PWM output. Code S0044 Backorder Price €29.49
All-in-one air quality sensor ZPHS01B: CO2, PM2.5, CH2O, O3... ZPHS01B is an all-in-one air quality module, which integrates laser dust sensor, infrared CO2 sensor, electrochemical formaldehyde, ozone and carbon monoxide sensors, VOC sensor, NO2 sensor, temperature and humidity sensor. Code S0151 ✗ Out-of-Stock Regular price €145.90 -€6.00 Price €139.90
CO₂ Humidity and Temperature Sensor - SCD40 (Qwiic) This SparkFun CO2, humidity and temperature sensor incorporates Sensirion's new generation of SCD40 photoacoustic CO2 sensors for highly accurate environmental readings. The sensor is capable of detecting concentrations from 0 to 40000 ppm with high precision above 400-2000 ppm ±(50 ppm+5%). The SCD40 has an integrated CMos® temperature and humidity sensor for greater precision. Code SP097 Last items in stock Price €74.95
PMS5003 High Accuracy Particle Concentration Sensor The sensors can be integrated into a variety of instruments associated with a concentration of airborne particles to improve equipment, provide timely concentration, and have Exact data. Present the laser that scatters products on airborne particles, at the same time at a specific angle collect scattered light, changing the intensity curve that scatters over time. The microprocessor uses the algorithm based on the MIE theory to deduce the grain size contained in the air and the concentration of the particles per unit and quantity. Characteristic: - Power supply: 4.5-5.5 VDC - Measurement range: 0.3-1.0ï¼ ›1.0-2.5ï¼› 2.5-10 µm (micrometer) - Accuracy of count: 50%@> Code S0046 Available Price €27.90
NDIR CO2 Sensor MH-Z14A Carbon dioxide detection MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime. Code S0149 Available Regular price €29.95 -€6.00 Price €23.95
MQ-135 Air Quality Sensor High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases. The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it. MQ-135 Air Quality Sensor features:- Main chip: MQ-135 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 10ppm - 300ppm NH3 10ppm - 1000ppm Benzene 10ppm - 300ppm Alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0034 Available Price €2.45
Dust Sensor Module PPD42NS PM2.5 This module is a dust sensor capable of detecting more than one micron of dust particles. It has two types of output: output of 4V high-level signal for a clean environment and 0.7V low-level signal for a particle-laden environment. Its power supply is 5VDC and the particle detection range is maximum at 8000 units per 283ml. Dust Sensor Module PPD42NS PM2.5 features: - Supply voltage: 5VDC - Working current: 90mA - Sensitivity: 0.5V / ( 0.1 mg / m3) - Particle detection minimum value: 1 micron - Output mode: Hi = 4V impulses (clean environment); Lo = 0.7V (charged environment) - Temperature working: 0-45 ° C - Working humidity: 0-90% RH - PCB size: 59x45x22 mm Code S0123 Available Regular price €11.89 -€2.00 Price €9.89
MH-Z1311A low-power consumption NDIR CO2 sensor Low power CO2 sensor MH-Z1311A, the current consumption is only 150-200uA, waterproof and anti-corrosion, high sensitivity, additionally characterised by excellent linear output. It is very popular used for battery monitors and IAQ devices. Code S0158 Available Price €29.49
Air Monitoring HAT for Raspberry Pi This HAT is an open source portable sensor that provides the level of suspended particulate matter quantity with its mass. It has a powerful and high-tech PMSA003 sensor that provides the information of suspended particulate matter (PM1.0, PM2.5, PM10) in the air per unit volume. Code RA127 ✗ Out-of-Stock Price €56.90
Air quality sensor ZP07-MP503 Gas detection The ZP07-MP503 air quality module offers high sensitivity with low power consumption and long life. Calibration before shipment from 10 seconds to 3 minutes max. with automatic warm-up function. Automatic fault check. Code S0150 Available Price €5.45
MH-Z19C Infrared Sensor module 5000ppm CO2 monitor HVAC PWM output UART CO2 sensor model MH-Z19C. High precision working voltage 5.0±0.1V DC. The measuring range is between 0 and 5000 ppm. It has a low power consumption. UART and PWM output. Code S0044 Backorder Price €29.49
All-in-one air quality sensor ZPHS01B: CO2, PM2.5, CH2O, O3... ZPHS01B is an all-in-one air quality module, which integrates laser dust sensor, infrared CO2 sensor, electrochemical formaldehyde, ozone and carbon monoxide sensors, VOC sensor, NO2 sensor, temperature and humidity sensor. Code S0151 ✗ Out-of-Stock Regular price €145.90 -€6.00 Price €139.90
CO₂ Humidity and Temperature Sensor - SCD40 (Qwiic) This SparkFun CO2, humidity and temperature sensor incorporates Sensirion's new generation of SCD40 photoacoustic CO2 sensors for highly accurate environmental readings. The sensor is capable of detecting concentrations from 0 to 40000 ppm with high precision above 400-2000 ppm ±(50 ppm+5%). The SCD40 has an integrated CMos® temperature and humidity sensor for greater precision. Code SP097 Last items in stock Price €74.95
PMS5003 High Accuracy Particle Concentration Sensor The sensors can be integrated into a variety of instruments associated with a concentration of airborne particles to improve equipment, provide timely concentration, and have Exact data. Present the laser that scatters products on airborne particles, at the same time at a specific angle collect scattered light, changing the intensity curve that scatters over time. The microprocessor uses the algorithm based on the MIE theory to deduce the grain size contained in the air and the concentration of the particles per unit and quantity. Characteristic: - Power supply: 4.5-5.5 VDC - Measurement range: 0.3-1.0ï¼ ›1.0-2.5ï¼› 2.5-10 µm (micrometer) - Accuracy of count: 50%@> Code S0046 Available Price €27.90