150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.99
Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC features: - Working voltage and TTL levels: 5V- Size: 44 x 14 mm Code C0013 Available Price €1.95
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €3.09
Vertical Liquid Level Sensor Switch Level sensor for liquids with float. The liquid level sensor acts as a switch. The state is changed by means of a magnet located on the float. It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where it is necessary to control the level of non-corrosive liquids such as water tanks, aquariums. Characteristic: - Maximum Load: 50W - Maximum Switching Voltage: 250V - Maximum Switching Current: 0.5A - Maximum charging current: 1A - Operating temperature: -10ºC to + 60ºC - Size: 58mm x 18mm Code S0043 Available Price €2.95
Resistor 4,7K Ohm 5% 0,25W 1/4W Resistor 4,7K Ohm 5% 0,25W 1/4W features:- 4.7K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0017 Available Price €0.08
Portable Magnetizer and Demagnetizer for Screwdriver RC Accessory It can be used to demagnetize tools or parts that you do not want to magnetize. Especially for magnetizing screwdriver bits or almost anything else. No batteries or electricity required, portable and easy to use. Code H0196 Available Regular price €2.49 -€0.50 Price €1.99
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.69
5x Strip Simple Row Male 40 Pins Header Various Colors 5x Strip Simple Row Male 40 Pins Header Various Colors features: - Type: Male- Insertion position: Vertical- Separation between pins: 2.54mm- Quantity: 5 strips of 40 pins Male each Code K0051 Available Price €1.29
RS232 USB to Serial TTL Adapter Module - USB to Serial PL2303HX PL2303 Ideal to connect TTL RS232 devices to your PC through the USB port. RS232 USB to Serial TTL Adapter Module - USB to Serial PL2303HX PL2303 features: > - Compatible PL2303 controller - 5 pins: 3.3V, 5.0V, TxR, RxD, GND - Heat shrinkable insulating cover - Led data transmission indicators - 2.5A self-recovery protector fuse - Supported OS: Win ME, Win2003, Win XP, Vista, Win 7 - Weight: 40 gr. (approx.) Code C0005 Available Price €1.49
RS232/485/422 to RJ45 Ethernet Module, TCP/IP to serial, POE Function Converter RS232/485/422 to Ethernet RJ45 has been designed for the industrial environment. It combines multiple functions including serial server, Modbus gateway, MQTT gateway, RS485 to JSON, etc. The module has an RS232/485/422 and Ethernet port (PoE function).Suitable for applications such as data acquisition, IoT gateway, IoT security. and smart device monitoring. Code WV015 Available Price €39.49
Adapter module CH340G LC Technology -TTL UART 5V series This is a CH340G TTL UART 5V serial adapter, designed to allow adding a USB connection to your project. In addition, this opens up the possibility of programming microcontrollers like the Arduino Pro mini. This module allows you to connect your project, from programming small microcontrollers to a custom computer keyboard. The module is ready for use of a UART connection. This may require the installation of a driver; however, it is a standard driver distributed by Microsoft Windows Update, available in Linux and that can be configured in MAC OS. Adapter module CH340G LC Technology -TTL UART 5V series features: - Manufacturer: LC Technology, - Communication chipset: CH340G - Communication: UART, - Pin connection: Code M0186 Available Regular price €2.50 -€0.51 Price €1.99
Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC features: - Working voltage and TTL levels: 5V- Size: 44 x 14 mm Code C0013 Available Price €1.95
SparkFun FTDI Basic Breakout - 5V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP023 Available Price €19.99
TTL Level Converter 5V - 3.3V IO LJ245A TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features: - Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument- VCCA power supply voltage: 4.5 - 5.5 VDC- VCCB power supply voltage: 2.7 - 3.6 VDC- Low level input voltage V (IL): 0.8 V- High-level input voltage V (IH): 2 V- Low level output current I (OL): 12 - 24 mA- High level output current I (OH): -24 - -12 mA- 8 channels allow the conversion of the IO communication level- Channel levels A and B are controlled by VCCA and VCCB Code C0017 Available Price €3.95
Adaptador DIP para USBASP Programador AVR Atmega8 Atmega128 Standard ISP download port, for on-line programming. Built-in crystal oscillator circuit (8MHz), crystal are replaceable. Has reset push button, power reset push button. Code B0073 Available Price €3.92
CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter features: - Ideal for connecting TTL RS232 RS485 devices to your PC through the USB port Code C0011 Available Price €7.95
6-pin/10-pin Kanda DIL adapter 6-pin/10-pin Kanda DIL adapter features: - Connector for Usbasp Programmer AVR Atmega8 Atmega128 Code B0051 Available Price €1.29
USBASP AVR ATmega8 ATmega128 Programmer Kanda Adapter Cable With KANDA adapter it is ideal for projects with ARDUINO. Characteristic: - AVR 5V / 3.3V microcontrollers - programming voltage change through jumper JP1 - Status LED indicators - Transmission speed: 5kB / s - Protective fuse of possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny € 15 ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S144, AT90S1434 ¦ Code B0021 Available Price €5.19
Bus Pirate - v3.6a This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board. This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin. Code SP037 Last items in stock Price €39.99
Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC features: - Working voltage and TTL levels: 5V- Size: 44 x 14 mm Code C0013 Available Price €1.95
CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter features: - Ideal for connecting TTL RS232 RS485 devices to your PC through the USB port Code C0011 Available Price €7.95
CP2102 USB 2.0 A RS232 Converter UART TTL Serial Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features: - Controller CP2102- 5 pins: 3.3v, 5.0v, TxR, RxD, GND- Standard USB type to male and 5 pin TTL connector- 3 Status LEDs: Power, RX and TX- USB 2.0 specification with 12Mbps maximum speed Code C0001 Available Price €3.70
Optical Isolated Converter FT232RL USB 2.0 to RS485 This converter has an internal DC / DC supply and a total isolation between the USB and the RS485 output and allows to establish a reliable and safe communication.Its FT232RL component has excellent compatibility and a communication rate up to 3M for a maximum distance of 1.2 km. The RS485 output interface uses an optical coupler with high speed for an optical insulation of 1500V and a protection against lightning of 600W: these characteristics allow to protect the computer from the potential damage of static electricity, lightning, over voltages and ground faults. Optical Isolated Converter FT232RL USB 2.0 to RS485 features: - Required systems: WINDOWS CE / 2000 / XP / VISTA / WIN 7 / LINUX / MAC OS- Internal DC /> Code C0015 Backorder Price €25.49
Adapter module CH340G LC Technology -TTL UART 5V series This is a CH340G TTL UART 5V serial adapter, designed to allow adding a USB connection to your project. In addition, this opens up the possibility of programming microcontrollers like the Arduino Pro mini. This module allows you to connect your project, from programming small microcontrollers to a custom computer keyboard. The module is ready for use of a UART connection. This may require the installation of a driver; however, it is a standard driver distributed by Microsoft Windows Update, available in Linux and that can be configured in MAC OS. Adapter module CH340G LC Technology -TTL UART 5V series features: - Manufacturer: LC Technology, - Communication chipset: CH340G - Communication: UART, - Pin connection: Code M0186 Available Regular price €2.50 -€0.51 Price €1.99
USB 2.0 to Parallel Adapter Cable DB25 Interface IEEE 1284 Printer A standard IEEE1284 DB25 parallel port to your PC via the USB port. Transmission speed reaches 12 Mbps. This cable is "USB Printing Support" port and not Parallel "LPT Printer Port" Code C0020 Available Price €2.99
TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level This bidirectional logic level converter can be used with normal series, I2C, SPI and other digital signals. It does not work with an analog signal.It is very easy to use. The card must be powered from the two voltages (high and low voltage) used by the system.A high voltage (5 V for example) to the pin "HV", low voltage (3.3 V for example) in "LV", and the system ground to pin "GND". TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level features: - 2 high voltage channels and low voltage logic logic for bidirectional translation- 2 low voltage channels High voltage high voltage logic in unidirectional conversion- The board module is compatible, it can be inserted directly in the use test panel- HV to 5 V power Code M0154 Available Regular price €4.59 -€1.60 Price €2.99
FTDI FT232RL USB-UART Converter - Mini USB FTDI FT232RL USB-UART Converter - Mini USB features: - Serial Converter USB-TTL 3.3V - 5V - LED indicator of Tx, Rx, power. - Communication: TTL COM Virtual RS232 RX / TX Transceiver - Voltage: 3.3V or 5V - per bridge - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA. - Size: 46 x 19 mm. Step 2.54mm. - Connection: Mini USB - Driver: Windows 7 / 8/10 Linux / Mac / Android - USB TO UART solution with mini USB connector - FT232RL original on board - Compatible with Mac, Linux, Android, WinCE, Windows 7/8 / 8.1 / 10 ... - 3 power mode: 5V output, 3.3V output or powered by the destination board (3.3V-5V) - 3 LEDs: TXD LED, RXD LED, POWER LED - Functional pins Code C0014 Available Price €12.95
Mini RS232 to TTL Adapter Max3232 Converter Mini RS232 to TTL Adapter Max3232 Converter features: - Converter for RS232 to TTL levels - MAX3232CSE chip - Voltage: 3V a 5V - Speed: no more than 120kbps - Dimensions: 16x9mm Code C0008 Available Price €1.49