SparkFun Pulse Oximeter and Heart Rate Sensor - MAX30101 & MAX32664 (Qwiic)

EMG Muscle Signal Sensor Signal Electromyography features:
EMG Muscle signal sensor module kit with 6 disposable electrodes The EMG sensor serves as a bridge to detect small electrical pulses product of
muscle activity and transform them into a signal recognizable by Arduino. NOTE: DO NOT USE THIS SENSOR FOR MEDICAL PURPOSES.
Code Examples: https: //github.com/AdvancerTechnologies/MuscleSensorV3

Ethanol alcohol sensor module.
MQ gas sensor uses a small indoor heater with an electrochemical sensor.
When the alcohol molecules in the air comply with the electrode the ethanol "changes" into acetic acid and then more current is produced.
MQ-3 Alcohol Sensor Module Ethanol Breathalyzer features:
- Main chip: alcohol sensor MQ-3 and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Detection concentration:
- 0.05mg/L - 10mg/L
- Quick response features:
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

This detection module that allows you to detect your heart rate and blood oxygen level from your Arduino project. You can monitor your blood oxygen level yourself to avoid going to the doctor or pharmacy on purpose. Simply press the sensor with your finger and wait for the reading of hemoglobin (Spo2), heart rate and Perfusion Index (PI%). It is a solution as an integrated heart rate sensor and pulse oximetry, which includes two LEDs, a photodetector and is optimized for analog low noise optics.

120x Female-Male Cables Female-Female Male-Male 2.54 Jumpers Dupont Arduino features:
- Length: 20cm
- Quantity: 120 cables
- Female-Female 40 units
- Male-Male 40 units
- Female-Male 40 units

Red Laser Module 650nm 5mW Head Point Adjustable Focal Length features:
- Type: red laser diode
- Laser type: point
- Adjustable Focus
- Wavelength: 650nm
- Output power: 5mW
- Operating voltage: 4.5-5V
- Operating intensity: <40mA
- Operating temperature: -30ºC to 60ºC
- Dimensions of the emitter: Φ12x35mm
- Cable length: 130mm

This module includes the BMP280 component that converts atmospheric pressure, temperature and humidity with high precision into a digital signal.
The equipment uses the two I2C and SPI interfaces. The very good measurements made by the BMP280 allows the module to be used as an altimeter.
Its 5-pin straight connector allows easy connection to other electronic boards. BMP280 Temperature Barometric Pressure Sensor Module/SPI features:
- Interfaces:
       -I2C (up to 3.4 MHz)
       -SPI (up to 10 MHz)
- Supply voltage: 1.8-5VDC
- Module operating range:
       - Temperature: -40ºC to + 85ºC
0-100%
       - Pressure: 300-1100 hPa
- Resolution of the measures:
       - Temperature: 0.01ºC

DFRobot Gravity (SEN0161): The analogue pH meter is specifically designed to measure the pH of the solution and reflect the acidity or alkalinity. The DFRobot ph sensor is commonly used in various applications such as aquaponics, aquaculture and environmental water testing. The pH is a value that measures acidity or alkalinity.

The module has two outputs: analog A0 and digital D0.
digital output D0 - signal 0 or 1 appears depending on the configuration of threshold.
The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - digital switching output indicator
- Measurements PCB: 3 x 1.5 cm
- Sensor measurements: 5.4 x 3.9 cm