MQ-9 Carbon Monoxide Sensor Module MQ-9 Carbon Monoxide Sensor Module features:- Main chip: MQ-9 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 20ppm- 2000ppm carbon monoxide 500ppm- 10000ppm methane CH4 500ppm- 10000ppm LPG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0033 Available Price €2.89
Protoboard Breadboard 400 points for Arduino It can be used to work with AVR, ARM, PIC microcontrollers, Arduino modules and to work with self-designed prototypes. Arduino Protoboard Breadboard 400 points features: -400 Connections -Linkable with other Plates -Base with adhesive to attach it to the work surface -Measures 82x55x8 mm Code PB002 Available Price €1.90
Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
Rechargeable battery 9V 6F22 Ni-MH 250 mAh Ready to Use Rechargeable battery 9V 6F22 Ni-MH 250 mAh Ready to Use features: Code PP049 Available Price €5.99
CP2102 USB 2.0 A RS232 Converter UART TTL Serial Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features: - Controller CP2102- 5 pins: 3.3v, 5.0v, TxR, RxD, GND- Standard USB type to male and 5 pin TTL connector- 3 Status LEDs: Power, RX and TX- USB 2.0 specification with 12Mbps maximum speed Code C0001 Available Price €3.70
Arduino compatible Attiny85 Digispark board Digispark is a development board based on the ATTINY85 microcontroller from ATMEL born in a successful campaign on Kickstarter. Similar to the Arduino line , It is one of the smallest boards on the market. Programmable directly from USB with the same Arduino tools. It has a built-in Micronucleus bootloader and can be replaced by similar ones such as the Trinket bootloader. Adafruit or others. You can use many of the same Arduino libraries and you have your own on the digispark wiki. Arduino compatible Attiny85 Digispark board features: - USB power supply - External power supply (7v-35v DC 12v maximum recommended) - 5V DC 500mA regulator on board - Programmable with the Arduino IDE - Loaded with Micronucleus bootloader Code B0002 Available Price €4.90
Blue Flat Steel and Plastic Screwdriver Philips blue flat screwdriver made of steel and plastic suitable for screws with 2.0mm head for electronic applications. Code H0126 Available Price €0.49
16x2 1602 LCD display Blue IIC/I2C LCD display consists of a 16-character, 2-rows. The display is compatible with the HD44780 controller Ideal for projects with Arduino You can use it with PIC, AVR, STM32 and many more controllers. Code P0010 Available Price €3.49
MH-Z1311A low-power consumption NDIR CO2 sensor Low power CO2 sensor MH-Z1311A, the current consumption is only 150-200uA, waterproof and anti-corrosion, high sensitivity, additionally characterised by excellent linear output. It is very popular used for battery monitors and IAQ devices. Code S0158 Available Price €29.49
Nova PM Sensor SDS011 - Air quality sensor - High precision laser PM2.5 Dust test module Air quality sensor with high precision whose SDS011 uses laser dispersion to detect particle concentration between 0.3 and 10 um in the air. With digital output by USB (UART) and built-in fan. It is a powerful sensor, fast (response less than 10s), accurate and reliable. Code S0142 Last items in stock Price €32.90
Dust Sensor Module PPD42NS PM2.5 This module is a dust sensor capable of detecting more than one micron of dust particles. It has two types of output: output of 4V high-level signal for a clean environment and 0.7V low-level signal for a particle-laden environment. Its power supply is 5VDC and the particle detection range is maximum at 8000 units per 283ml. Dust Sensor Module PPD42NS PM2.5 features: - Supply voltage: 5VDC - Working current: 90mA - Sensitivity: 0.5V / ( 0.1 mg / m3) - Particle detection minimum value: 1 micron - Output mode: Hi = 4V impulses (clean environment); Lo = 0.7V (charged environment) - Temperature working: 0-45 ° C - Working humidity: 0-90% RH - PCB size: 59x45x22 mm Code S0123 Available Regular price €11.89 -€2.00 Price €9.89
CJMCU-811 CCS811 Carbon monoxide VOC CO Digital air quality gas sensor The Carbon Monoxide sensor is a low-power digital gas sensor which has a CCS811 sensor and an 8-bit microcontroller, contains an analog-digital converter so that it can detect indoor air quality which can detect monoxide carbon (CO) and a wide range of volatile organic compounds (VOCs). It is a sensor designed to monitor air quality inside personal devices such as mobile devices and smart watches, with low power consumption that can be used with battery Code S0140 Available Price €17.95
Air purifier with HEPA filter This air purifier uses a HEPA filter to safely remove viruses, bacteria, mold, mildew, dander, etc. Filters up to 99.5% of dust, pollen, tobacco smoke, mould spores and pet dander. Keeps the environment clean. Code VE018 Last items in stock Price €89.00
MH-Z19C Infrared Sensor module 5000ppm CO2 monitor HVAC PWM output UART CO2 sensor model MH-Z19C. High precision working voltage 5.0±0.1V DC. The measuring range is between 0 and 5000 ppm. It has a low power consumption. UART and PWM output. Code S0044 Backorder Price €29.49
Dehumidifier and air purifier 2 in 1 This air purifier uses a HEPA filter to remove viruses, bacteria, mould, dander, etc. safely. The dehumidifier regulates humidity in the bathroom, kitchen, etc. Filters up to 99.5% of dust, pollen, tobacco smoke, mould spores and pet dander. Keeps the environment clean. Code VE019 Out-of-Stock Price €149.00
Air Monitoring HAT for Raspberry Pi This HAT is an open source portable sensor that provides the level of suspended particulate matter quantity with its mass. It has a powerful and high-tech PMSA003 sensor that provides the information of suspended particulate matter (PM1.0, PM2.5, PM10) in the air per unit volume. Code RA127 ✗ Out-of-Stock Price €56.90
NDIR CO2 Sensor MH-Z14A Carbon dioxide detection MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime. Code S0149 Available Regular price €29.95 -€6.00 Price €23.95
All-in-one air quality sensor ZPHS01B: CO2, PM2.5, CH2O, O3... ZPHS01B is an all-in-one air quality module, which integrates laser dust sensor, infrared CO2 sensor, electrochemical formaldehyde, ozone and carbon monoxide sensors, VOC sensor, NO2 sensor, temperature and humidity sensor. Code S0151 ✗ Out-of-Stock Regular price €145.90 -€6.00 Price €139.90
MH-Z1311A low-power consumption NDIR CO2 sensor Low power CO2 sensor MH-Z1311A, the current consumption is only 150-200uA, waterproof and anti-corrosion, high sensitivity, additionally characterised by excellent linear output. It is very popular used for battery monitors and IAQ devices. Code S0158 Available Price €29.49
Nova PM Sensor SDS011 - Air quality sensor - High precision laser PM2.5 Dust test module Air quality sensor with high precision whose SDS011 uses laser dispersion to detect particle concentration between 0.3 and 10 um in the air. With digital output by USB (UART) and built-in fan. It is a powerful sensor, fast (response less than 10s), accurate and reliable. Code S0142 Last items in stock Price €32.90
Dust Sensor Module PPD42NS PM2.5 This module is a dust sensor capable of detecting more than one micron of dust particles. It has two types of output: output of 4V high-level signal for a clean environment and 0.7V low-level signal for a particle-laden environment. Its power supply is 5VDC and the particle detection range is maximum at 8000 units per 283ml. Dust Sensor Module PPD42NS PM2.5 features: - Supply voltage: 5VDC - Working current: 90mA - Sensitivity: 0.5V / ( 0.1 mg / m3) - Particle detection minimum value: 1 micron - Output mode: Hi = 4V impulses (clean environment); Lo = 0.7V (charged environment) - Temperature working: 0-45 ° C - Working humidity: 0-90% RH - PCB size: 59x45x22 mm Code S0123 Available Regular price €11.89 -€2.00 Price €9.89
CJMCU-811 CCS811 Carbon monoxide VOC CO Digital air quality gas sensor The Carbon Monoxide sensor is a low-power digital gas sensor which has a CCS811 sensor and an 8-bit microcontroller, contains an analog-digital converter so that it can detect indoor air quality which can detect monoxide carbon (CO) and a wide range of volatile organic compounds (VOCs). It is a sensor designed to monitor air quality inside personal devices such as mobile devices and smart watches, with low power consumption that can be used with battery Code S0140 Available Price €17.95
Air purifier with HEPA filter This air purifier uses a HEPA filter to safely remove viruses, bacteria, mold, mildew, dander, etc. Filters up to 99.5% of dust, pollen, tobacco smoke, mould spores and pet dander. Keeps the environment clean. Code VE018 Last items in stock Price €89.00
MH-Z19C Infrared Sensor module 5000ppm CO2 monitor HVAC PWM output UART CO2 sensor model MH-Z19C. High precision working voltage 5.0±0.1V DC. The measuring range is between 0 and 5000 ppm. It has a low power consumption. UART and PWM output. Code S0044 Backorder Price €29.49
Dehumidifier and air purifier 2 in 1 This air purifier uses a HEPA filter to remove viruses, bacteria, mould, dander, etc. safely. The dehumidifier regulates humidity in the bathroom, kitchen, etc. Filters up to 99.5% of dust, pollen, tobacco smoke, mould spores and pet dander. Keeps the environment clean. Code VE019 Out-of-Stock Price €149.00
Air Monitoring HAT for Raspberry Pi This HAT is an open source portable sensor that provides the level of suspended particulate matter quantity with its mass. It has a powerful and high-tech PMSA003 sensor that provides the information of suspended particulate matter (PM1.0, PM2.5, PM10) in the air per unit volume. Code RA127 ✗ Out-of-Stock Price €56.90
NDIR CO2 Sensor MH-Z14A Carbon dioxide detection MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime. Code S0149 Available Regular price €29.95 -€6.00 Price €23.95
All-in-one air quality sensor ZPHS01B: CO2, PM2.5, CH2O, O3... ZPHS01B is an all-in-one air quality module, which integrates laser dust sensor, infrared CO2 sensor, electrochemical formaldehyde, ozone and carbon monoxide sensors, VOC sensor, NO2 sensor, temperature and humidity sensor. Code S0151 ✗ Out-of-Stock Regular price €145.90 -€6.00 Price €139.90