Dust Sensor Module PPD42NS PM2.5

ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features:
Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino /

This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.
The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.
The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB).

MQ-8 Hydrogen Gas Sensor Module features:
- Main chip: MQ-8 methane sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
  100ppm- 10000ppm hydrogen H2
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

Allows control: - Up to 2 bidirectional current motors
- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features:
- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 36 V
- Maximum current: ± 1.2 A
- Logic voltage: - 2.3V <= HIV <= VIN (high)
                        - 0.3V <= VIL <= 1.5V (low)
- Controller L293D
- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA
- D2, D4 - motorB

Easily convert water level to analog signal
The analog output signal can be read directly on the Arduino board
Characteristic:
- Operating voltage: 3.3V -5 V
- Consumption: less than 20 mA - Sensor type: Analog
- Operating temperature: 10º C -30º C
- Detection area: 40 mm x 16 mm
- Dimensions: 60 mm x 20 mm

DC Gear Motor 6V 148 Arduino features:
- Voltage: 3 to 6Vdc
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Reduction: 1:48

Arduino Sensor Shield V5 APC220 features:
Sensor Shield V5.0 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate
- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more

The module is based on a touch sensitive IC capacitive touch switch module (TTP223B).
In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features:
- Low power consumption
- Input voltage: 2 - 5.5VDC
- Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation
- 3-pin control interface:
1- GND
2- VCC
3- Control signal (output pin)
- Power indicators: Bright green LED when the sensor is on