Sonoff DUALR3 - Wireless Smart Switch SONOFF DUALR3 is a WiFi based 2-gang switch that can independently connect and control two connected devices or lights - this simply means that 1 SONOFF DUALR3 control switch is equivalent to 2 Sonoff basic switches! The three working modes of DualR3 are switch mode, motor mode and meter mode. Code WS043 Available Price €16.99
Resistor 2M Ohm 5% 0,25W 1/4W Resistor 2M Ohm 5% 0,25W 1/4W features:-2M Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0032 Available Price €0.08
Resistor 220K Ohm 5% 0,25W 1/4W Resistor 220K Ohm 5% 0,25W 1/4W features:-220 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0027 Available Price €0.08
Silicone Thermal Paste Syringe 25g Silicone Thermal Paste Syringe 25g features: - Density at 20°C: 2.58 G/cm3- Flashpoints: 350°C- Freezing point: -50°C- Coefficient of refraction: 1.405,- Specific temperature at 50°C: 0.243 Cal/g K- Co-efficient global heat transfer at 0-150°C: 0.78 W/m K- Constant dielectric at 100 Hz: 4.7 (± 0.1)- Cross resistance: 5 x 10 to the power 14 Ohm x cm- Loss rate at f = 100 Hz: 0.020 (± 0.003)- Range of operating temperature: -50~200°C Code Q0008 Available Price €4.79
74HC595 SN74HC595N 8-Bit DIP-16 With this multiplexer circuit we will be able to get 8 more digital outputs for arduino losing only 3 of them. Code T0020 Available Price €0.49
Transparent Box for W1209 DIY Transparent Box for W1209 DIY features: For W1209 Thermostat DC 12V temperature controller Code M0107 Available Price €2.65
Resistor 47K Ohm 5% 0,25W 1/4W Resistors 47K Ohm 5% 0,25W 1/4W features:-47K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0023 Available Price €0.08
Smart Garden Irrigation Control ZigBee 3.0 TUYA Zigbee 3.0 irrigation controller for garden. The latest generation ZigBee 3.0 protocol, together with the Tuya Smart app, allows you to create a real smart home. Once you have set the correct schedules for each day of the week, you can forget about remembering to water your garden every day. Code WT013 Backorder Price €43.90
2x Cable Alligator Clip Black and Red Multimeter 2x Cable Alligator Clip Black and Red Multimeter features: - Length: 90cm- Colors: red and black- Quantity: 2 Cables Code K0016 Available Price €2.99
Resistor 100K Ohm 5% 0,25W 1/4W Resistor 100K Ohm 5% 0,25W 1/4W features: 100K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0026 Available Price €0.08
10x Linear Potentiometer 100k OHM kΩ 10x Linear Potentiometer 100k OHM kΩ features:- 100k Ohm kΩ Linear- Horizontal variable resistance PCB- Quantity: 10 units Code K0063 Available Price €0.12
HC-SR04 + Ultrasonic Sensor Support for Arduino compatible sensors It is very easy to make it work with an Arduino, PIC or any other microcontroller.In its output pin we can measure the pulse width PWM depending on the distance of the obstacle.Mounting bracket is ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. HC-SR04 + Ultrasonic Sensor Support Arduino features: - Supply voltage: 5V (4.5V-6V)- Consumption: typical 30 mA, (35 mA max)- Interface: VCC, GND, Signal- Range: 2 cm to 3 meters- Angle 15º- LED measurement indicator in progress- Frequency: 40 kHz for 200 μs- Size: 30 mm x 20 mm Feature of the support: - Material: Acrylic- Transparent color- Includes screws Code S0006 Available Regular price €3.24 -€0.60 Price €2.64
Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna A Mini WIFI board ESP8266 contains 16MB flash, external antenna connector and built-in ceramic antenna based on ESP-8266EX. Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: - Compatible with Arduino, programming with the Arduino IDE, MicroPython, NodeMCU - Supply voltage: 5V - Logical levels: 3.3V - 16MB (128Mbit) flash - 11 pins of input / output - I2C / one-wire interface, LOLIN I2C port - 1 ADC (input: 0-3.2V) - built-in ceramic antenna - external antenna connector - Power switch - Includes external WIFI antenna with IPEX SMA adapter Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: of esp8266: - Supported protocols: 802.11 b / g / n - Network support: 2 , 4 GHz Code W0098 Available Price €10.90
Resistor 10 ohm 5% 0,25W 1/4W carbon film resistor Resistencias (10 Ohm) de tolerancia de 0.05 y potencia de 0,25W. En el carbon film. Code D0002 Available Price €0.08
Resistor 22 Ohm 5% 0,25W 1/4W Resistors 22 Ohm 5% 0,25W 1/4W features:-22 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0003 Available Price €0.08
SparkFun ESP8266 Thing - Dev Board (wo headers) ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes without headers. Code SP007 Last items in stock Price €25.99
Resistor 510 ohm 5% 0,25W 1/4W carbon film resistor Resistencias (510 Ohm) de tolerancia de 0.05 y potencia de 0,25W. En el carbon film. Code D0011 Available Price €0.08
Resistor 5,1K Ohm 5% 0,25W 1/4W Resistor 5,1K Ohm 5% 0,25W 1/4W features:-5.1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0018 Available Price €0.08
SONOFF ZBMINI-L ZigBee 3.0 Smart Switch - No neutral wire required Sonoff ZBMINI-L is a universal switch controlled by ZigBee. It works with 240V voltage and enables control of any device anywhere in the world, controlling it by your mobile phone or voice assistants such as Alexa. Thanks to its small size it fits in most power supplies. No neutral wire required. Code WS047 Available Price €15.99
Plastic Housing DB9 DB15 Cover Connector RS232 D-SUB Plastic Housing DB9 DB15 Cover Connector RS232 D-SUB features: - Plastic housing for DB9 DB15 connector Code K0084 Available Price €0.98
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Last items in stock Price €34.99
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP039 Last items in stock Price €33.99
Cable 1x1.5 Flexible Single-pole 1.5mm black 1m Characteristic: -Low voltage electric cables -Normal: EN 50525-2-31 -Number of conductors: 1x1.50mm2 -Service voltage: 450 / 750V -Service temperature: at 70ºC -Resistance at 20ºC: 13.3 Ohm / Km -Weight (Kg / Km): 21 -External diameter: 3.4mm -Length 1m Code K0041 Available Price €1.08
Cable 1x1.5 Flexible Single-pole 1.5mm green-yellow 1m Characteristic: -Low voltage electric cables -Normal: EN 50525-2-31 -Number of conductors: 1x1.50mm2 -Service voltage: 450 / 750V -Service temperature: at 70ºC -Resistance at 20ºC: 13.3 Ohm / Km -Weight (Kg / Km): 21 -External diameter: 3.4mm -Length 1m Code K0043 Available Price €1.08
Slide Linear Potentiometer 10K OHM kΩ Slide Linear Potentiometer 10K OHM kΩ features: - Ideal for application in electronic circuits, MCU. ARM and Arduino projects- Value: 10k Ohm- Type: Linear variable resistance- Tolerance: 20%- Power: 250mW (1 / 4W)- Dimensions 90x20 mm- Analog voltage signal 0 - VCC- Double outlet OTA, OTB- Quantity: 1 unit Code M0054 Available Price €2.89
10x Linear 5K Potentiometer OHM kΩ Linear 5K Ohm Potentiometer features:- Horizontal variable resistance PCB- 5K Linear Code K0064 Available Price €0.20
Cable 1x0.35 Flexible Single-pole 0.35mm blue 3m Characteristic: -Low voltage electric cables -Normal: EN 50525-2-31 -Number of conductors: 1x0.35mm2 -Service voltage: 300 / 500V -Service temperature: at 70ºC -Resistance at 20ºC: 55.0 Ohm / Km -Weight (Kg / Km): 7 -Outer diameter: 2.4mm -Length 1m Code K0035 Backorder Price €0.45
Cable 1x0.35 Flexible single-pole 0.35mm red 3m Characteristic: -Low-voltage electric cables -Standard: EN 50525-2-31 -Number of conductors: 1x0.35mm2 -Service voltage: 300 / 500V -Service temperature: at 70ºC -Resistance at 20ºC: 55.0 Ohm / Km -Weight (Kg / Km): 7 -Outer diameter: 2.4mm Code K0033 Backorder Price €0.45
SONOFF POW Elite Smart Power Meter Switch - POWR316 SONOFF POW Elite 16A is a power meter switch with a newly upgraded ESP32 chip that is 200% faster than the previous ESP8622 chip. Version without lcd display, you can track the real-time power, current and voltage of your appliances and the accumulated power consumption. Code WS063 Available Price €24.49
1N4007 Rectifier Diodes 1A 1000V DO-41 1N4007 Rectifier Diodes 1A 1000V DO-41 features:- Standard rectifier diode- Configuration: Simple- Reverse voltage: 1000V- Direct voltage drop: 1V- Direct direct current: 1A- Maximum overvoltage current: 30A- Encapsulated: DO-41- Operational tension: -65ºC to + 125ºC Code T0002 Available Price €0.05
FinestraMiner Helium LoRaWAN Gateway Hotspot Miner FinestraMiner is a highly efficient Helium compatible hotspot that provides wireless network coverage to the Helium network, also called People's Network, the world's largest and fastest growing LoRaWAN network. It allows thousands of IoT devices to connect to this single hotspot using Long-Fi technology, with long-range coverage up to 16 kilometres away. The Helium network is a decentralised wireless network that allows devices anywhere in the world to connect to the Internet wirelessly. Code W0800 Available Price €675.00
NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features: - Standard: NFC Forum Type2 Tag Ntag215 - Protocol: ISO14443A - Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ - Reading distance: 0-10CM - Communication speed: 106Kboud - Working temperature: -20ºC to 70ºC - Number of uses 100,000 times - Data retention: 10 years - Material: PVC - Dimensions 86 x 54 x 0.84 mm Code M0052 Available Price €1.99
Light Sensor Module BH1750 FVI Arduino and Raspberry compatible Descripción: Light sensor module to measure light intensity and obtain digital data from it.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.BH1750FVI (Rohm) is used to adjust backlighting of LCD screens and keyboards by manufacturers of mobile phones, digital cameras, navigation and portable gaming devices. Light Sensor Module BH1750 FVI Arduino Raspberry features: - Chip BH1750FVI- Supply voltage 3V-5V- Integrated 16bit AD converter- Detection range: 0-65535 lx (with an accuracy of 1 lux)- Interface: II2C- Low dependence on the light source (eg incandescent lamp, fluorescent lamp, halogen lamp, white LED, sunlight)- Dimensions 18.4 x 14 mm Code M0019 Available Price €2.99
Cable 1x0.35 Flexible single-pole 0.35mm black 1m Cable 1x0.35 Flexible single-pole 0.35mm² black features: -Conductor: Flexible Copper -Insulation: PVC -Low voltage electrical cables -Standard: EN 50525-2-31 -Number of conductors: 1x0.35mm² -Service voltage: 300 / 500V -Service temperature: at 70ºC -Resistance at 20ºC: 55.0 Ohm / Km -Weight (Kg / Km): 7 -Outer Diameter: 2.4mm Code K0031 Backorder Price €0.45
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.15
ADXL345 3-Axis Accelerometer SPI and I2C Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It serves to measure the static acceleration, for example gravity, in applications where you need to measure the inclination.Also to measure dynamic acceleration, movement. ADXL345 3-Axis Accelerometer SPI and I2C features: - Type: 3-axis accelerometer- Chip: ADXL345- Supply voltage: 3-5V- Consumption: 40uA active and 0.1uA on hold- Communication: SPI and I2C- Measurements: Static and dynamic acceleration- Accelerometer scales ± 2g, ± 4g, ± 8g and ± 16g- Resolution: 13 bits- Dimensions: 20x16mm- Operating temperature: -40 °C to +80 °C- Detection: Free fall, click-double click Code M0018 Available Price €3.09
ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 51 x 19 x 16 mm Code W0006 Available Price €9.90
10x Photoresistor GL5539 LDR 50k - 100k Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:- Model: GL5539- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 50-100KΩ- Resistance with darkness (0lux): 5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0013 Available Price €0.15
2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino 2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL004 Available Regular price €3.15 -€0.50 Price €2.65
SONOFF ZBMINIL2 ZigBee 3.0 Smart Switch - No neutral wire required Sonoff ZBMINI-L2 is the latest version of universal switch controlled by ZigBee. It works with 240V voltage and enables control of any device anywhere in the world, controlling it by your mobile phone or voice assistants such as Alexa. Thanks to its small size it fits in most power supplies. No neutral wire required. Code WS083 ✗ Out-of-Stock Price €15.99
8 Channel High Trip 5V 10A Relay Module This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, from the TTL 8 Channel High Trip 5V 10A Relay Module features: - Channels: 8 (independent protected with Optocouplers) - Supply Voltage Vcc: 5Vdc - Output Current: 10A - High trip min 3.3V input IN1. ..IN8 - Relay activation current: 5 ~ 10mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 55x 139mm - Weight: 120g COM GND jumper input: connects GND optocouplers and GND of the circuit Code RL015 Available Price €9.95
NTC thermistor 100K 3950 1m RepRap cable Sensor used to measure the temperature of the hotend or hot bed of your 3D printer Characteristic: - NTC Thermistor 100 K 3950 - Impedance: 100 K (25º of Temperature) - Accuracy: 1% - Sensor Diameter: 1.8 mm - Cable Length: 1 m - Cable: AWM UL 3398 150 ° C 300V - Ready to be installed and used. Fully insulated - Designed to withstand the high temperatures of extrusion of plastics such as PLA and ABS Code I0018 Available Price €1.10
Barometric Pressure, Temperature and Altitude Sensor BMP180 Barometric Pressure, Temperature and Altitude Sensor BMP180 features: - Module based on the atmospheric pressure sensor BMP180- Supply voltage: 1.8 - 3.6 V- Energy consumption: 0.5uA- I2C interface- Measuring range: 300 - 1100hPa- Dimensions: 10 x 13 mm- Includes soldering pins Code M0024 Available Regular price €3.89 -€0.59 Price €3.30
2x PCF8574P I/O Extension Board 8574 NXP - The PCF8574P is an 8-bit remote I / O expander for the I2C bus with 16-pin DIP packet interrupt. - Provides general-purpose remote I / O expansion via a two-wire, two-way I2C bus (Serial Clock (SCL), Serial Data (SDA)). - Devices consist of eight quasi-directional ports , 100KHz I2C bus interface, three hardware address inputs and interrupt output operating between 2.5V and 6V. - Quasi-bidirectional port can be independently assigned as one input to monitor interrupt status or keyboards or as an output to activate indicating devices like LEDs. - System Master can read from the input port or write to the output port through a single register. Code T0010 Available Price €1.15
GP2Y0A21YK0F Strong Infrared IR Distance Meter Characteristic: - Supply voltage: 4.5V- 5.5V - Consumption: 30 mA typical - Analog output - Range: 10cm to 80cm - Dimensions: 29x12mm - Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino Code S0024 Available Price €9.95
NRF24L01 + Wireless Transceiver Module 2.4GHz It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features: - Based on chip NRF24L01 + Ultra Low Power- Free band: 2.4GHz ISM- Speed: 250kbps, 1Mbps, 2Mbps- Working current - reception: 13 mA- Transmission: 11 mA (900nA -deep sleep mode)- Receiving sensitivity: -94dB 250kbps- Coverage in closed spaces: 15m / 30m- SPI interface- Input voltage: 1.9V- 3.6V- Input / output port voltage: 0V-3.3V / 5V- Coverage in open areas: 100m approx.- Clock frequency: 16MHz Code W0005 Available Price €1.59
Peltier Ceramic Cell TEC1-12702 12V 2A Characteristic: - Max Power: 24w - Voltage: 12v - Max Current: 2A - Cooling capacity 17.7W - Temperature variation: Code M0051 Available Price €6.99
L293D Quadruple Half-H Drivers STM L293D Quadruple Half-H Drivers STM features:-Continue 0.6A half-h driver STM Arduino Code T0014 Backorder Price €1.85
Current Sensor ACS712 AC/DC 20A Hall Current Ammeter Sensor used to measure the current in the circuit to which it is connected. It is based on the ACS712 chip, capable of measuring intensity in both DC and AC. Current Sensor ACS712 AC/DC 20A Hall Current Ammeter features: - Output: Analog - Power: 5V - Accuracy: 1.5% - Measuring capacity: +/- 20A - Dimensions: 31 x 13 mm Code M0105 Available Price €2.99
E18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car Ideal for projects with ARDUINO, Smart CarDetects transparent and translucent obstaclesE18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car features:- Current consumption: up to 100 mA- Supply voltage 5V- Current consumption <25mA- Response time of 2 ms- Measured distance: 3-80cm 15st angle- Screw to adjust the sensitivity, the back- Output status led indicator- Operating temperature: -25°C - + 55°C- Material: high-strength plastic- Type of output: normally open, NPN- Dimensions: 18 mm in diameter, Length 45 mm- Cable length 55cm- Departures: - Brown: + - Blue: - - Black: OUT Code S0004 Available Price €6.95
5x Power LED Aluminum Heat Sink 1W 3W 5x Power LED Aluminum Heat Sink 1W 3W features: - Outside diameter: 36mm- Height: 15mm- Quantity: 5 units Code P0037 Available Price €1.48
USBASP Atmega8 AVR Programmer Atmega128 Arduino compatible Adapter Cable Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1 - LED status indicators - Transmission speed: 5kB / s - Fuse protector against possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦ Code B0029 Available Price €6.59
NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features: - Operating voltage: 5V- Wait time of the module receives the data: more than 2S- The waiting time of the module sends data: more than 300- Transfer speed: 50 Byte / S (theoretical value)- I2C / TWI address: 0 x 47 (decimal 35)- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)- Size: 44 x 23 mm Code W0066 Available Price €4.46
Antenna with Magnetic Base Male GSM GPRS 3G 800MHz 1800MHz 1900MHz 7dBI SMA Antenna with Magnetic Base Male GSM GPRS 3G 800MHz 1800MHz 1900MHz 7dBI SMA features:- Standard: GSM / GPRS / 3G- Frequency range: 800 ~ 1900MHz- Interface: SMA male- Gain: 7dBi- Length of the antenna: 20cm- V.S.W.R .: <1.5- Impedance (ohm): 50- Maximum input power (W): 100W- Operating temperature: -40ºC ~ + 70ºC Code W0072 Available Price €6.95
Qwiic cable protoboard - 4 pin This cable is an essential element of the Qwiic ecosystem - it enables connection between the protoboard and any device with a Qwiic connector. With all the benefits of Qwiic at hand - no soldering required, easy 1-second hookup on click and dismantling. The cable is 150mm long. Wires are color coded according to scheme: Code SP020 Available Price €1.99
2x CNY70 Reflective Optical Sensor with Transistor Output 2x CNY70 Reflective Optical Sensor with Transistor Output features: - Reflective optical sensor with transistor output- Reflective optical coupler used to distinguish edge or line detection- Dimensions of the housing are 7 x 7 x 6 mm- Supply voltage: 5V- Maximum diode current: 50 mA- Maximum collector-emitter voltage: 32V- Maximum collector current of 50 mA- Quantity: 2 units Code S0121 Available Price €0.74
Qwiic cable 50mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 50mm long Code SP040 Available Price €1.19
Low Loss Coax Cable H-155 2.4GHz WiFi LTE GSM Low Loss Coax Cable H-155 2.4GHz WiFi LTE GSM features:- The cable is used for system transmissions2.4 [GHz] (WiFi, LTE, 3G, GPS)- It is also suitable for the lower frequencies (CB, GSM, PMR)- It has less loss than the type RG-58 cable- Type of coaxial cable- H155 cable series- 50Ω wave impedance- Stranded core structure- Core type Cu- Structure of the laminated Al-PET shield, tinned copper braid- PVC external insulation material- Gray insulation color- Outer cable dimensions Ø5.4mm- Operating temperature -15 ... 70 ° C- Resistance to weather conditions- Installation of 2.4 GHz antenna cable, outdoor- Attenuations [dB / 100m]:* 50 [MHz] - 6.5* 100 [MHz] - 9.3 Code K0056 Available Price €2.80
Qwiic cable 100mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 100mm long Code SP022 Available Price €1.99
Relay SRD-05 DC-2P 5V 10A SPDT - SRD-05VDC-SL-C Relay SRD-05 DC-2P 5V 10A SPDT features:- Supply voltage: 5V- Output Current: 10A- For power switching with 5V DC signals - Microcontroller, Arduino, Electronica Code RL011 Available Price €0.69
Limit Switch with Wheel - 5A 250 Vac - 1 switched - Arduino compatible Limit Switch with Wheel - 5A 250 Vac - 1 switched - Arduino features: -Micro KW12-3 on / off switch -Max Current: 5A -AC voltage: 125-250V -Operating temperature: -40 to 70 degrees C -Quantity: 2 units Code K0018 Available Price €0.59
3x Power LED Aluminum Heat Sink 3W 5W 3x Power LED Aluminum Heat Sink 3W 5W features: - Outside diameter: 36mm- Height: 30mm- Quantity: 3 units Code P0038 Available Price €1.95
Relay SRD-12 DC-2P 12V 10A SPDT Relay SRD-12 DC-2P 12V 10A SPDT features:- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- For power switching with 12V DC signals - Microcontroller, Arduino, Electronica Code RL012 Available Price €0.98
Universal Magnetic Antenna Connector Male Plug SMA 150cm GPS Universal Magnetic Antenna Connector Male Plug SMA 150cm GPS features: - Standard: GPS 1575.42 MHz- Voltage: 3 ~ 5V- Current: max 10mA- Interface: SMA male- Polarization: circular (right)- LNA gain (without cable): 28dB typ- Noise figure: 1.5dB typ- Operating temperature: -40'C ~ + 85'C- Cable length 150cm- Dimensions: 49 x38 x16 mm Code W0073 Available Price €7.59
Fan 12V 2x Cables PC CPU case Fan 12V 2x Cables PC CPU case features: - Voltage: 12V - Consumption: 0.28A - Screw diameter: 3.5mm - Life time useful: 30,000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 24.5cm - Dimensions: 80mm x 80mm x 15mm Code I0055 Available Regular price €3.49 -€0.90 Price €2.59
4-Channel 5V 10A Relay Module Characteristic: - Channels: 4 (independent protected by Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 54x 72mm - 5V Optocoupled 4-Channel Relay Module - This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for the remote control + 4-channel 315 MHz IC2262 receiver: - Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver Code RL007 Available Price €3.99
16x2 1602 LCD display Blue IIC/I2C LCD display consists of a 16-character, 2-rows. The display is compatible with the HD44780 controller Ideal for projects with Arduino You can use it with PIC, AVR, STM32 and many more controllers. Code P0010 Available Price €3.49
LED Diode COB 10W Orange SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet.The advantages of LED COB:- A luminous performance of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without needing to concentrate so much the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional lightMount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0034 Available Price €2.83
NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino compatible NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0065 ✗ Out-of-Stock Price €1.49
Momentary Push button Switch N/A NO 2A 36V 16mm Stainless Steel Momentary Pushbutton Switch N/A NO 2A 36V 16mm Stainless Steel features: - Type of operation: momentary (automatic return)- Contact switch: 1 NA (normally open)- Max Switch Classification: 2A / 36VDC- Type of terminal: Screw- Body material: Stainless steel- Button Material: Stainless steel- Protection Classification: IP67 / IK08- Operating temperature: -20C + 55C Code K0094 Available Price €4.49
Metal Switch 16mm Stainless Steel Latching Metal Switch 16mm Stainless Steel features:- For panel N/A NO 2A 36V Stainless Steel On/Off- Type of operation: On/Off- Contact switch: 1 NA (normally open)- Max Switch Classification: 2A/36VDC- Type of terminal: Screw- Body material: Stainless steel- Button Material: Stainless steel- Protection Classification: IP67 / IK08- Operating temperature: -20C + 55C Code K0095 Available Price €3.69
Flat Cable 1m AWG28 1.27 10 Pins Colors The cables are in 10 different colors Flat Cable 1m AWG28 1.27 10 Pins Colors features: - Length: 100cm - Model AWG28 - Product name: Flat cable - Number of conductors: 10 - Conductive material: Copper - Insulation voltage: 300V - Inner diameter 0.32mm - Pin Pitch: 1.27mm - Temperature: 105 ° C Code K0003 Available Regular price €3.49 -€0.51 Price €2.98
Flat Cable 1m AWG28 1.27 Gray 10 Pins Flat Cable 1m AWG28 1.27 Gray 10 Pins features: - Length: 100cm - Model AWG28 - Product name: Flat cable - Number of conductors: 10 - Conductive material: Copper - Insulation voltage: 300V - Inner diameter 0.32mm - Pin Pitch: 1.27mm - Temperature: 105 ° C Code K0002 Available Price €2.50
12V Push Button LED Red 16mm 12V Push Button LED Red 16mm features:- Momentaneo panel N/A NO with return 2A Steel- Type of operation: momentary (automatic return)- Contact switch: 1 NA (normally open)- Max Switch Classification: 2A / 12VDC- Body material: Stainless steel- Button Material: Stainless steel- Protection Classification: IP67 / IK08- Operating temperature: -20C + 55C Code K0096 Available Price €5.89
12V Push Button LED Green 16mm 12V Push Button LED Green 16mm features:- Momentaneo panel N/A NO with return 2A Steel- Type of operation: momentary (automatic return)- Contact switch: 1 NA (normally open)- Max Switch Classification: 2A / 12VDC- Body material: Stainless steel- Button Material: Stainless steel- Protection Classification: IP67 / IK08- Operating temperature: -20C + 55C Code K0097 Available Price €5.89
12V Momentary LED Push Button Switch White 16mm N/A NO 12V Momentary LED Push Button Switch White 16mm N/A NO features: - Type of operation: Momentary (automatic return)- Contact switch: 1 NA (normally open)- Max Switch Classification: 2A / 12VDC- Body material: Stainless steel- Button Material: Stainless steel- Protection Classification: IP67 / IK08- Operating temperature: -20C+ Code K0098 Available Price €5.89
12V Momentary LED Pushbutton Blue 16mm N/A NO 12V Momentary LED Pushbutton Blue 16mm N/A NO features:- Type of operation: momentary (automatic return)- Contact switch: 1 NA (normally open)- Max Switch Classification: 2A / 12VDC- Body material: Stainless steel- Button Material: Stainless steel- Protection Classification: IP67 / IK08- Operating temperature: -20C + 55C- Color: Blue Code K0099 Available Price €5.89
Cable Silicona SIF 0.5mm2 Cu -50...+180°C Black flexible - roll 100m Flexible multi-conductor (stranded) SIF type flexible copper cable with silicone insulation. Conductor; silicone; SIF; 1 conductor; Cu; 0.50mm2; black; silicone; halogen free; heat resistant; -50...+180°C; 300/500V; 100m coil; Lappkabel; RoHS; OLFLEX HEAT 180 SIF; 2.1mm; 1x0.50mm2. Code K0101 Available Price €69.95
Silicone Cable Li2G 0.5mm2 10A 1kV -50÷180°C Black Flexible Double silicone insulated cables. Extremely flexible. The inner insulation is white which makes it easy to see if there is any damage. Resistant to low and high temperatures. Ideal for measuring cables used for dangerous voltages. Code K0109 Available Price €2.85
Silicone Cable Li2G 0.5mm2 10A 1kV -50÷180°C Red Flexible Double silicone insulated cables. Extremely flexible. The inner insulation is white which makes it easy to see if there is any damage. Resistant to low and high temperatures. Ideal for measuring cables used for dangerous voltages. Code K0108 Available Price €2.85