Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.30
12V On/Off LED Pushbutton Red 16mm N/A NO Latching push-button 12V normally open- For panel N / A NO 2A 36V Stainless Steel on / off- Type of operation: On / Off- Contact switch: 1 NA (normally open)- Max Switch Classification: 2A / 12VDC- Body material: Stainless steel- Button Material: Stainless steel- Protection Classification: IP67 / IK08- Operating temperature: -20C + 55C- Color: Red Code K0194 Available Regular price €4.87 -25% Price €3.65
LED 1W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 20-30LM - Ã beam angle: 120 degrees - Color emission: blue Code P0047 Available Price €0.81
12 V supply module with 2A step-up output on/off DM13 Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 12 VDC, - Fixed output voltage: 12 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0093 Available Price €3.22
12V On/Off LED Pushbutton Green 16mm N/A NO Characteristic:- For panel N / A NO 2A 36V Stainless Steel on / off- Type of operation: On / Off- Contact switch: 1 NA (normally open)- Max Switch Classification: 2A / 12VDC- Body material: Stainless steel- Button Material: Stainless steel- Protection Classification: IP67 / IK08- Operating temperature: -20C + 55C- Color: Green Code K0193 Last items in stock Price €4.87
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €2.88
Battery holder 2x AA Battery holder with switch Includes a switch to output the voltage built into the case itself. It has a cover to protect the batteries. The cover has perforation in case you want to secure it with a screw (not included). Battery holder 2x AA Battery holder with switch features: - Cable 15cm long - Measurements 68x 32x 18mm - Battery length max 50mm - Compatible batteries (LR06, R06, MN1500, AM3, UM3 , HP7) Code PP005 Available Price €1.15
LED Power Diode COB 12W White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes. Code P0030 ✗ Out-of-Stock Price €2.79
WS2812B Addressable 16x16 Flexible RGB LED Array Programmable LED module with flexible display, 256-pixel matrix light, individually addressable. WS2812B are LEDs that have integrated logic, so it is possible to vary the colour of each LED individually. WS2812B has a built-in integrated logic within each LED, which allows access to each pixel individually. For this reason these LEDs are called individually indexable. They are based on the 5050 LED. Code P0206 Available Price €14.83
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0163 Available Price €4.09
LED 3W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.1-4.1V - Current: 700mA - Luminous flux: 39-55LM - Ã beam angle: 120 degrees - Color emission: blue Code P0152 Available Price €1.31
Aluminum Heat Sink 10x2.5cm Power LED 3W 5W The aluminium heatsink for 3W to 5W LEDs. It is 10cm long, 2.5cm wide, 1.0cm high. Code P0049 Available Price €2.88
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V FC-102 for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0156 Available Price €5.70
WS2812B RGB LED Strip White 1m 30 LED/M IP65 WS2812B RGB LED Strip White 1m 30 LED/M IP65 features: - IP65 RGB Addressable Smart Arduino - RGB LED WS2812B S2812B are LEDs that have integrated logic, so it is possible to vary the color of each LED individually S2812B includes a built-in inside each LED, which allows each pixel to be accessed individually - For this reason, these types of LEDs are called individually indexable - They are based on the 5050 LED - 30 individually indexable LED diodes - 24-bit color control (8-bit PWM per channel) - 16.8 million colors by LED - One-wire communication - Power: 5 V idth: 11 mm - Thickness: 2.6 mm - Length: 1 meter - Consumption: 1.8A (all white) ater resistant Code P0103 Available Price €8.06
LED Power Diode COB 7W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0147 Available Price €1.74
White Diode 9W LED COB SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone-coated tabletThe advantages of LED COB:- A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Opening angle of up to 160º Code P0029 Available Price €2.42
LED Power Diode COB 7W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0143 Available Price €1.74
LED Diode COB 20W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0032 Available Price €3.71
WS2812B Addressable 16x16 Flexible RGB LED Array Programmable LED module with flexible display, 256-pixel matrix light, individually addressable. WS2812B are LEDs that have integrated logic, so it is possible to vary the colour of each LED individually. WS2812B has a built-in integrated logic within each LED, which allows access to each pixel individually. For this reason these LEDs are called individually indexable. They are based on the 5050 LED. Code P0206 Available Price €14.83
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0163 Available Price €4.09
LED 3W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.1-4.1V - Current: 700mA - Luminous flux: 39-55LM - Ã beam angle: 120 degrees - Color emission: blue Code P0152 Available Price €1.31
Aluminum Heat Sink 10x2.5cm Power LED 3W 5W The aluminium heatsink for 3W to 5W LEDs. It is 10cm long, 2.5cm wide, 1.0cm high. Code P0049 Available Price €2.88
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V FC-102 for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0156 Available Price €5.70
WS2812B RGB LED Strip White 1m 30 LED/M IP65 WS2812B RGB LED Strip White 1m 30 LED/M IP65 features: - IP65 RGB Addressable Smart Arduino - RGB LED WS2812B S2812B are LEDs that have integrated logic, so it is possible to vary the color of each LED individually S2812B includes a built-in inside each LED, which allows each pixel to be accessed individually - For this reason, these types of LEDs are called individually indexable - They are based on the 5050 LED - 30 individually indexable LED diodes - 24-bit color control (8-bit PWM per channel) - 16.8 million colors by LED - One-wire communication - Power: 5 V idth: 11 mm - Thickness: 2.6 mm - Length: 1 meter - Consumption: 1.8A (all white) ater resistant Code P0103 Available Price €8.06
LED Power Diode COB 7W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0147 Available Price €1.74
White Diode 9W LED COB SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone-coated tabletThe advantages of LED COB:- A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Opening angle of up to 160º Code P0029 Available Price €2.42
LED Power Diode COB 7W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0143 Available Price €1.74
LED Diode COB 20W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0032 Available Price €3.71