Soldering Iron Tip Cleaner Ball Soldering tip cleaner allows removing the solder residues from the tips.It cleans better and does not cause temperature drops like with sponges.You do not need extra water to clean the tip.Easy and effective cleaning at the tip. Code H0198 ✗ Out-of-Stock Price €2.47
XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.02
20x Ceramic Capacitor 100pF 50v 2,54 PCB PIC 0.022uF for Arduino 20x Ceramic Capacitor 100pF 50v 2,54 PCB PIC Arduino 0.022uF features:-Type: ceramic NPO-Tolerance: +/-5%-Dimensions: diameter 5mm, pitch 2.54mm Code D0063 Available Price €0.04
LED Power Diode COB 12W White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes. Code P0030 ✗ Out-of-Stock Price €2.79
Push button 6x6x4mm Push button 6x6x4mm features: -Touch Push Tact Switch mini electronic Arduino push button -Measures: 6x6x4.3mm Code K0079 Available Price €0.17
Resistor 220 Ohm 5% 0,25W 1/4W Resistor 220 Ohm 5% 0,25W 1/4W features:-220 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0008 Available Price €0.07
Blue Propeller for Micro Motor 3V 5 6V DC DIY for Arduino Blue Propeller for Micro Motor 3V 5 6V DC DIY Arduino Code R0084 Available Price €0.65
Batch of 600 Units 1/4W Resistors Various values Ohm Ω Batch of 600 Units 1/4W Resistors Various values Ohm Ω features: - Each lot contains (30 x 20 units): 10Ω, 22Ω, 47Ω, 100Ω, 150Ω, 200Ω, 220Ω, 270Ω, 330Ω, 470Ω, 510Ω, 680Ω, 1KΩ, 2KΩ, 2.2KΩ, 3.3KΩ, 4.7KΩ, 5.1KΩ, 6.8KΩ, 10KΩ, 20KΩ, 47KΩ, 51KΩ, 68KΩ, 100KΩ , 220KΩ, 300KΩ, 470KΩ, 680KΩ, 1M - Tolerance: ± 5% - Power: 0.25W Code D0070 Available Price €3.26
Aluminum Heat Sink 15x2cm LED 1W-3W Aluminum Heat Sink 15cm 2cm LED 1W 3W features:Aluminum heatsink for LED 1W-3W, Length: 15cm, Width: 2.0cm, Height: 0.6cm. Code P0051 Available Price €2.31
LED strip cold white 12V 3528 5m /300 Strip of 300 cold white coloured LED lights, 5 metres long. Code K0593 Available Price €9.05
LED Power Diode COB 15W White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0031 Last items in stock Price €3.07
LED 1W Orange SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 2.2-2.4V - Current: 300mA - Luminous flux: 40-50LM - Ã Beam angle: 120 degrees - Color emission: yellow / orange Code P0045 Available Price €0.81
High Power LED Chip Diode 10W Blue SMD COB COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A luminous performance of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without needing to concentrate so much the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light - Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little thermal silicone in each of the placement centers of the diodes- The thermal paste increases the thermal transfer between the diode and the metal plate used as circuit Code P0033 Available Price €2.34
WS2812B Addressable 8x32 Flexible RGB LED Array Programmable LED module with flexible display, 256-pixel matrix light, individually addressable. WS2812B are LEDs that have integrated logic, so it is possible to vary the colour of each LED individually. WS2812B has a built-in integrated logic within each LED, which allows access to each pixel individually. For this reason these LEDs are called individually indexable. They are based on the 5050 LED. Code P0207 Available Price €15.66
WS2812B Addressable 8x8 Flexible RGB LED Array Programmable LED module with flexible display, 64-pixel matrix light, individually addressable. WS2812B are LEDs that have integrated logic, so it is possible to vary the colour of each LED individually. WS2812B has a built-in integrated logic within each LED, which allows access to each pixel individually. For this reason these LEDs are called individually indexable. They are based on the 5050 LED. Code P0205 Available Price €9.05
RGB LED Strip WS2812 5m with IR and Bluetooth remote control This RGB LED strip is based on LED WS2812. It is equipped with 30 LEDs and has a length of 5 metres. You can easily control the behaviour of these LEDs using the included remote control or using your mobile phone via Bluetooth. Watch the video for more info. Code SS017 Available Regular price €29.33 -10% Price €26.40
LED 1W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 20-30LM - Ã beam angle: 120 degrees - Color emission: blue Code P0047 Available Price €0.81
LED Diode 1W Warm White SMD 130LM Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 2.85-3.85V - Current: 350mA - Luminous flux: 120-130LM - Beam angle: 130 degrees Code P0151 Last items in stock Price €0.81
Aluminum Heat Sink 15x2cm LED 1W-3W Aluminum Heat Sink 15cm 2cm LED 1W 3W features:Aluminum heatsink for LED 1W-3W, Length: 15cm, Width: 2.0cm, Height: 0.6cm. Code P0051 Available Price €2.31
LED strip cold white 12V 3528 5m /300 Strip of 300 cold white coloured LED lights, 5 metres long. Code K0593 Available Price €9.05
LED Power Diode COB 15W White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0031 Last items in stock Price €3.07
LED 1W Orange SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 2.2-2.4V - Current: 300mA - Luminous flux: 40-50LM - Ã Beam angle: 120 degrees - Color emission: yellow / orange Code P0045 Available Price €0.81
High Power LED Chip Diode 10W Blue SMD COB COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A luminous performance of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without needing to concentrate so much the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light - Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little thermal silicone in each of the placement centers of the diodes- The thermal paste increases the thermal transfer between the diode and the metal plate used as circuit Code P0033 Available Price €2.34
WS2812B Addressable 8x32 Flexible RGB LED Array Programmable LED module with flexible display, 256-pixel matrix light, individually addressable. WS2812B are LEDs that have integrated logic, so it is possible to vary the colour of each LED individually. WS2812B has a built-in integrated logic within each LED, which allows access to each pixel individually. For this reason these LEDs are called individually indexable. They are based on the 5050 LED. Code P0207 Available Price €15.66
WS2812B Addressable 8x8 Flexible RGB LED Array Programmable LED module with flexible display, 64-pixel matrix light, individually addressable. WS2812B are LEDs that have integrated logic, so it is possible to vary the colour of each LED individually. WS2812B has a built-in integrated logic within each LED, which allows access to each pixel individually. For this reason these LEDs are called individually indexable. They are based on the 5050 LED. Code P0205 Available Price €9.05
RGB LED Strip WS2812 5m with IR and Bluetooth remote control This RGB LED strip is based on LED WS2812. It is equipped with 30 LEDs and has a length of 5 metres. You can easily control the behaviour of these LEDs using the included remote control or using your mobile phone via Bluetooth. Watch the video for more info. Code SS017 Available Regular price €29.33 -10% Price €26.40
LED 1W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 20-30LM - Ã beam angle: 120 degrees - Color emission: blue Code P0047 Available Price €0.81
LED Diode 1W Warm White SMD 130LM Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 2.85-3.85V - Current: 350mA - Luminous flux: 120-130LM - Beam angle: 130 degrees Code P0151 Last items in stock Price €0.81