2x CNY70 Reflective Optical Sensor with Transistor Output

It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features:
- Based on chip NRF24L01 + Ultra Low Power
- Free band: 2.4GHz ISM
- Speed: 250kbps, 1Mbps, 2Mbps
- Working current - reception: 13 mA
- Transmission: 11 mA (900nA -deep sleep mode)
- Receiving sensitivity: -94dB 250kbps
- Coverage in closed spaces: 15m / 30m
- SPI interface
- Input voltage: 1.9V- 3.6V
- Input / output port voltage: 0V-3.3V / 5V
- Coverage in open areas: 100m approx.
- Clock frequency: 16MHz

  - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields   Characteristic:   - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: micro USB female 

It allows to save the record of any data.
It has a real time clock RTC, with battery included, so you can keep the date and time over the years and an SD notes reader, which accepts the format FAT16 and FAT32 to record your data. Logging Recorder Data Logger Module Shield UNO Mega SD Card features:
- Arduino data logging shield
- Data recording module to the FAT16 / FAT32 SD card
- Real time with RTC battery.
- SD card interface compatible with the FAT16 / FAT32 format
- Transmitter circuit level 3.3V.
- Compatible with Arduino UNO, Leonardo, ADK / Mega R3 or higher

The module has two outputs: analog A0 and digital D0
Digital output D0 - signal 0 appears or 1 depending on the threshold setting
The threshold is set with the potentiometer
The sensor can be used for example:
Automatic watering for potted plants
With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants
Characteristic:
Operation: 3.3V -5V
- Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - indicator digital switching output
- PCB measurements: 3 x 1.5 cm
- Probe measurements: 6 x 3 cm

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

The MAX9812 is a sound amplifier specially designed to treat the signal coming from microphones.
We can use it together with Arduino to measure sound from a processor like Arduino.
When we saw the modules with microphone we commented that, in general, the signal generated is too low to be registered correctly.
If we want to be able to measure sounds, we will have to amplify the signal. The MAX9812L has single / dual inputs, fixed gain of 20dB, bandwidth of 400 kHz, low noise and low signal distortion 0.015% THD.
There are two models, its supply voltage is 2.7V to 3.6V.
We can use the sensors with MAX9812 for applications that require measuring the intensity or frequency of the sound.

Ideal to power your Arduino board through the power input.
Adapter Battery 9V 6F22 Jack Connector DC features:
- Cable 7cm long
- Battery connector 9V, 6F22
- Male connector DC 5.5 / 2.5

TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink

Compared to the TMC2100 module, the TMC2208 controller module emits less heat.