Multiplexer 16 Channels CD74HC4067 MUX/DEMUX A multiplexer of this type actually only acts as a switch 16 to a 1.The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features: - Based on chip CD74HC4067- Analog signal input: Y0-Y15, 16 channels- Analog signal output: Z pin- Digital input, channel control: S0-S3- Module size: approx. 4 x 1.8cm- Package includes:* 1 x CD74HC4067 MUX connection module* 2 x row of soldering pins Code C0006 Available Price €2.88
Ceramic Heater Cartridge 12V 40W 3D Printer - Ideal for use with Reprap Prusa 3D printers & amp; Mendel, with 1m shielded cable Characteristic: - Voltage 12V - Power 40W - Material: Ceramic y Stainless steel - Cartridge diameter 6 mm - Cartridge length 20 mm - Cable length approx. 1000 mm Code I0050 Available Price €1.48
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.12
Power supply 5V 3A 15W USB-C Mobile Charger 5V 3A 3100mA with connector USB-C. This power supply has an additional USB-A connector. Code RA066 ✗ Out-of-Stock Price €9.01
Tilt Camera Platform Anti-Vibration Camera Mount for Aircraft FPV Tilt Camera Platform Anti-Vibration Camera Mount for Aircraft FPV features:- Platform for Arduino Robotics Modeling, works with servo 9g SG90- Servos not included Code R0022 Available Regular price €1.78 -€0.20 Price €1.58
Light Sensor Module BH1750 FVI Arduino and Raspberry compatible Descripción: Light sensor module to measure light intensity and obtain digital data from it.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.BH1750FVI (Rohm) is used to adjust backlighting of LCD screens and keyboards by manufacturers of mobile phones, digital cameras, navigation and portable gaming devices. Light Sensor Module BH1750 FVI Arduino Raspberry features: - Chip BH1750FVI- Supply voltage 3V-5V- Integrated 16bit AD converter- Detection range: 0-65535 lx (with an accuracy of 1 lux)- Interface: II2C- Low dependence on the light source (eg incandescent lamp, fluorescent lamp, halogen lamp, white LED, sunlight)- Dimensions 18.4 x 14 mm Code M0019 Available Price €2.47
Arduino Uno Wifi Rev2 Imagine the simplicity of the Arduino One connected to the communication module. Seems too good to be true, right? That's Arduino One WiFi. Arduino Uno WiFi REV2 (ABX00021) with its integrated IMU (Inertial Measurement Unit) and WiFi is the ideal board to start making your first Internet application from scratch, or to use in the educational field. It has 14 digital input / output pins (5 of which are PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, an accelerometer, an RGB LED, a power connector and an ICSP header. Code BAR21 Available Regular price €46.77 -€5.00 Price €41.77
20x4 2004 LCD display PCF8574T I2C Backlit Blue - It consists of a 20-character, 4-row display - The display is compatible with the controller HD44780 and integrates the module so you can use it through the I2C protocol without any problem - Only two pins are needed for communication, SDA and SCL - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - It can be changed to any between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 20x4 2004 LCD display PCF8574T I2C Backlit Blue features: - LCD screen, 20 characters and 4 lines - 5V power supply - HD44780 compatible controller Code P0013 Available Price €7.02
Speed sensor module for Arduino motors Speed sensor module for Arduino motors features: - Slot-type optocoupler sensor, slot width: 10 mm. - The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it. - Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high - Power supply: 3.3-5V - Current consumption 15 mA max. - PCB dimensions: 25 x 20 mm Code S0129 Available Price €1.55
2x CNY70 Reflective Optical Sensor with Transistor Output 2x CNY70 Reflective Optical Sensor with Transistor Output features: - Reflective optical sensor with transistor output- Reflective optical coupler used to distinguish edge or line detection- Dimensions of the housing are 7 x 7 x 6 mm- Supply voltage: 5V- Maximum diode current: 50 mA- Maximum collector-emitter voltage: 32V- Maximum collector current of 50 mA- Quantity: 2 units Code S0121 Available Price €0.62
Speed sensor module for Arduino motors Speed sensor module for Arduino motors features: - Slot-type optocoupler sensor, slot width: 10 mm. - The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it. - Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high - Power supply: 3.3-5V - Current consumption 15 mA max. - PCB dimensions: 25 x 20 mm Code S0129 Available Price €1.55
2x CNY70 Reflective Optical Sensor with Transistor Output 2x CNY70 Reflective Optical Sensor with Transistor Output features: - Reflective optical sensor with transistor output- Reflective optical coupler used to distinguish edge or line detection- Dimensions of the housing are 7 x 7 x 6 mm- Supply voltage: 5V- Maximum diode current: 50 mA- Maximum collector-emitter voltage: 32V- Maximum collector current of 50 mA- Quantity: 2 units Code S0121 Available Price €0.62