Speed sensor module for Arduino motors
  • Speed sensor module for Arduino motors

Speed sensor module for Arduino motors

S0129

Speed sensor module for Arduino motors features:
- Slot-type optocoupler sensor, slot width: 10 mm.
- The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it.
- Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high
- Power supply: 3.3-5V - Current consumption 15 mA max.
- PCB dimensions: 25 x 20 mm

OEM
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Speed sensor module for Arduino motors features:

- Slot-type optocoupler sensor, slot width: 10 mm.
- The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it.
- Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level.

The operating mode:

- When the sensor is blocked the OUT output is high
- Power supply: 3.3-5V < br /> - Current consumption 15 mA max.
- PCB dimensions: 25 x 20 mm

Customers who bought this product also bought

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

RL001

Price €1.98

DRV8833 Controller DC Motor PAP

Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ). The motors are controlled, independently by means of PWM signals the direction of rotation of the motors can be controlled, neutral or stop with a frequency of up to 100 kHz. Two input signals (IN1 and IN2) can be used to control one motor (connected to OUT1 and OUT2) and the other two input signals (IN3 and IN4) to control the second motor (connected to OUT3 and OUT4). NOTE: This DRV8833 dual-bridge motor controller is the replacement for the TB6612FNG dual-channel motor controller. The pins come unsoldered. If the motor draws currents above 0.6A, the use of a heat sink may be required. DRV8833 Controller DC Motor PAP features:

R0082

Price €2.02

Acrylic box with fan for Raspberry Pi 4 model B

All ports and slots on the case can perfectly match Raspberry Pi 4 Model B. Acrylic box with fan for Raspberry Pi 4 model B features:
- clear acrylic case x 1 You. - 5Vdc fan - mounting screw x 1 set Note: The Raspberry Pi board is not included.

RA072

Regular price €3.63 -20% Price €2.90

TM1637 4-Digit Digital Display Module

Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +.
The display module 4-digit LED with TM1637.
The unit can be controlled with just two DIO and CLK control lines.
TM1637 4-Digit Digital Display Module features:

- 3V-5V supply voltage
- Current consumption 250 mA
- 7-segment display 4 digits common anode
- Digit size: 0.36 inches
- Dimensions: 42x24x11mm

M0104

Price €1.78

IR Remote Control + IR Infrared Receiver VS1838

IR Remote Control + IR Infrared Receiver VS1838 features:
- The test distance is about 5-8 meters, but practical application depends on environmental factors (such as diaphragm, glass , obstructions or other material blockage) - The CHQ1838 / HX1838 receiver receives the 38kHz signal
- Vcc supply: 3.3V-5V
- IN digital output to connect to the port Arduino I / O
- Remote measurements 85x 40x 5mm
- Includes battery
Useful links for Arduino / Raspberry programming and projects with Arduino boards / Raspberry:
Send / Receive information via IR
- Wiring of the IR Remote control + Infrared IR Receiver VS1838 with the UNO module
- Light a 3mm red LED by Infrared

W0021

Price €2.06
€1.55

1,55 tax excl.

1
Last 5 items
Price €1.55

Order until 4pm we will send today
30 days return