Cable 1x0.35 Flexible single-pole 0.35mm red 3m
  • Cable 1x0.35 Flexible single-pole 0.35mm red 3m

Cable 1x0.35 Flexible single-pole 0.35mm red 3m

K0033

Characteristic:
-Low-voltage electric cables
-Standard: EN 50525-2-31
-Number of conductors: 1x0.35mm2
-Service voltage: 300 / 500V
-Service temperature: at 70ºC
-Resistance at 20ºC: 55.0 Ohm / Km
-Weight (Kg / Km): 7
-Outer diameter: 2.4mm

OEM
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Characteristic:

-Low-voltage electric cables
-Standard: EN 50525-2-31
-Number of conductors: 1x0.35mm2
-Service voltage: 300 / 500V
-Service temperature: at 70ºC
-Resistance at 20ºC: 55.0 Ohm / Km
-Weight (Kg / Km): 7
-Outer diameter: 2.4mm

Customers who bought this product also bought

DC Gear Motor and Tire Wheel for Smart Car Robot

DC Gear Motor and Tire Wheel for Smart Car Robot features:
- Voltage: 3 to 6 Vdc
- Reduction: 1:48
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Dimensions of the wheel: diameter 65mm - width 26 mm

R0011

Price €3.21

40x Female-Female Cable 10cm

40x Female-Female Cable 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont female connectors on both ends
- Compatible with 2.54mm male connectors
- High quality and good working conditions
- Easy to install and use

K1005

Price €1.64

Kontakt PCB PLUS Spray 400ml

The PCB PLUS cleaner is designed for printed circuit boards.
Dissolves waste flux, including resin.
The liquid does not attack the substrate or the structural components of the printed circuit boards.
The special brush to remove particles and smaller debris. Perfect for cleaning PCB after repair and assembly.
PCB Plus Cleanser Spray 400ml features:
- Form: spray
- Capacity: 400ml
Application:
- The product does not leave deposits
- It evaporates very fast
- Eliminates waste after welding
- Perfect in any electronic service
- The product does not react with most plastics used in electronics

Q0071

Price €8.22

DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo

Descent module.
Use a multimeter to check the output voltage and adjust the potentiometer.
Control of voltage and current.
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo features:
- Input voltage: 4-38V
- Output voltage: 1.25-36V
- Current output: adjustable, 4.5A (max 5A)
- Output power: 75W maximum
- Operating temperature: -40 to + 85 ºC
- Operating frequency: 180KHz
- Efficiency conversion: up to 96%
- Short circuit protection: Yes (limited current 8A)
- Protection over temperature: the output switches off automatically
- Size: 62mm x 26mm x 14mm
Principal functions:
- Step-down converter with overcurrent protection
- Li-Po battery charger, Li-Ion

A0014

Price €2.88

Barometric Pressure, Temperature and Altitude Sensor BMP180

Barometric Pressure, Temperature and Altitude Sensor BMP180 features:
- Module based on the atmospheric pressure sensor BMP180
- Supply voltage: 1.8 - 3.6 V
- Energy consumption: 0.5uA
- I2C interface
- Measuring range: 300 - 1100hPa
- Dimensions: 10 x 13 mm
- Includes soldering pins

M0024

Regular price €3.21 -€0.59 Price €2.62

Sensor Module Moisture Earth Water Soil

The module has two outputs: analog A0 and digital D0
Digital output D0 - signal 0 appears or 1 depending on the threshold setting
The threshold is set with the potentiometer
The sensor can be used for example:
Automatic watering for potted plants
With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants
Characteristic:
Operation: 3.3V -5V
- Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - indicator digital switching output
- PCB measurements: 3 x 1.5 cm
- Probe measurements: 6 x 3 cm

S0021

Price €1.61

Pro Mini 8MHZ 3.3V Arduino compatible board

Miniaturized compatible version of Arduino Pro Mini.
It has an Atmega328P chip running at 8Mhz with a factory loaded bootloader. It does not include pins so - we can solder only the pins that we need. Pro Mini 8MHZ 3.3V Arduino compatible board features:
- ATmega328P 8MHz chip with external quartz crystal - Auto-reset - micro switch
- Integrated 3.3V regulator
- FLASH 32kB memory
- SRAM 1kB memory
- EEPROM 1Kb memory
- Analog input A0-A7
- 8 PWM channels
- external interruption
- TWI / I2C, UART, SPI interfaces
- Power and status LEDs
- Dimensions: 18x33mm - Weight: 30 grams An adapter is needed to program it

B0017

Price €7.40
€0.37

0,37 tax excl.

7
Pre-order
Do you want to receive an alert when product is back in stock?
 
We will send you an email once the product becomes available. Your email address will not be shared with anyone else.
Price €0.37

Order until 4pm we will send today
30 days return