The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

Inlet Module Plug Fuse Switch 220V C14 3D Printer features:
- Voltage and current of 10A, 250V AC
- Plug type - 3 pins IEC320 C14
- Color of the red switch
- Diameter holes 40 mm
- Distance between holes 39mm
- Size 47 x 27 mm
- Total size of 58 x 50 x 34 mm

Necessary for the protection of printed circuits.
PCB varnish of high quality for manufacturing, repair and maintenance.
Prevents the oxidation of printed circuit boards during intermediate storage. Insulating Varnish Spray 400ml features:
-A protective film, transparent.
-Protects soft metals for welding (eg copper, steel, lead, tin, brass) against corrosion, moisture, oxidation, dust, chemical contamination
-It maintains the welding, to carry out a subsequent welding it is not necessary to eliminate the
protective film
-PVB 16 is used, for example, in the storage of printed circuit boards and material that is going to be
soldier, such as welding terminals or conductors.
-Temperature of application: od -40 ° C + 60 ° C.

The package includes 10 pcs. of Peltier cell insulating washer, 1 pc. of silicone paste 7 grams.

Set of 7 pieces of multicolour PVC insulating tape. Ideal for electrical insulation. PVC insulating tape with adhesive

Set of 10 pieces of multicolour PVC insulating tape tesaflex® 53988. Ideal for electrical insulation. PVC insulating tape with adhesive

Isopropyl alcohol is used for cleaning: - of electronic devices such as contact tips (such as those of ROM cartridges)
- tapes magnetic and disk heads (such as those for audio and video recorders and floppy drives)
- laser lenses on optical disc drives (eg CD, DVD) and removal of thermal paste of heat sinks and integrated circuit packages (for example: CPU)
-of the keyboard and LCD screen
-Usefully used to clean photographic lens lenses and contacts of electronic devices as it leaves no marks and is quick to evaporate.

Isopropyl alcohol is used for cleaning: - Of electronic devices, such as contact tips (such as those of ROM cartridges).
- magnetic tapes and disc heads (such as those of audio and video recorders and flexible disk drives).
- laser lenses in optical disk drives (for example: CD, DVD) and the removal of thermal paste from heat sinks and integrated circuit packages (for example: CPU) of the keyboard and the LCD screen. Very used in the cleaning of lenses of photographic lenses and contacts of electronic devices, since it does not leave marks and is of rapid evaporation. It is sold commercially also as a cleaner for shales.

NVIDIA® Jetson Nano ™ Developer Kit is a small computer with powerful capabilities that allows you to run multiple neural networks in parallel for applications such as image classification, segmentation, speech processing and object detection. All this in an easy-to-use platform that runs on just 5 watts. Thanks to this board, the power of modern Artificial Intelligence is now available to Makers, students and embedded developers everywhere. Discover the power of AI and robotics with the powerful 4GB NVIDIA Jetson Nano Developer Kit. Now educators, students, and any enthusiast can easily perform AI projects quickly and efficiently using their GPU-accelerated NVIDIA software.

This smart home kit is based on the open source micro:bit hardware and is intended for those who want to create smart home projects that improve the comfort of the home through technology. The kit has been launched by Keyestudio. The kit does not include the micro:bit board.

This smart home kit is based on the open source micro:bit hardware and is intended for those who want to create smart home projects that improve the comfort of the home through technology. The kit has been launched by Keyestudio. The kit includes the micro:bit board.

The Makey Makey clone board - economic and compatible - is small and has a USB port to connect it to a computer and alligator clips to connect other objects. Just plug, clip and play, no programming skills or cumbersome software installation required. With a set-up in seconds, your child can get inventing, whether at home or in the classroom.

The kit contains the Mega board, the Ramps 1.4 shield and 4 A4988 controllers with heatsinks.

Raspberry Pi 400- PC embedded in a keyboard + accessories is the ideal tool, both educational, perfect for students of all ages, and for personal use. This RPi based on model 4, offers a low cost and portable solution, being ideal for home study and for teaching computer concepts such as programming, physical computing and networking. 

The Raspberry Pi 400 has a quad-core ARM Cortex A72 processor with 4GB of RAM, an Ethernet socket, 3 USB ports, two microHDMI ports and a 40-pin GPIO.

Raspberry Pi Zero W is a super small computer. This version includes WIFI, Bluetooth BLE 4.1 Pi Zero is the heart of a Raspberry Pi on a small 65mm x 30mm board. With mini-HDMI, micro-B OTG USB, and the same 40-pin GPIO, it still has a great connectivity. Raspberry Pi Zero 512MB RAM WIFI BLE 4.1. Supplied with a GPIO soldered connector.

  Perfect "Kit XXL Mega Sensors" to learn programming with Arduino, the basis of electronics. It allows to build various projects of various complexity, from the easiest ... to the most complicated
The elements are placed in the box to keep everything in order.
100% suitable with screen, RFID and keyboard.   Characteristic:   It includes the following module references:   - 1x Mega2560 Development Board Arduino Module - 1x LED Display Screen Controller Blue Backlight 16x2 1602 HD44780
- 1x Prototype Protoboard MB-102 830 points Arduino
- 1x 74HC595 74595 SN74HC595N 8-Bit Shift Register DIP-16
- 1x LM35 Temperature Sensor LM35DZ TO92
- 2x SW-520D Vibration Tilt Sensor
- 1x fire sensor
- 3x Photoresistor GL5516 LDR

Perfect "Kit XXL Sensors" to learn programming with Arduino, the basis of electronics. It allows to build various projects of various complexity, from the easiest ... to the most complicated. The elements are placed in the box to keep everything in order. The kit does not include an Arduino board. An original Arduino board or a Chinese equivalent can be purchased separately.  

12mm Bore Pillow Block Mounted Bearing is often suited to support rotating shaft applications.

8mm Bore Pillow Block Mounted Bearing is often suited to support rotating shaft applications.

The module for DIY Arduino hobby
Motor driver L9110 for Arduino, Smart Car, Robotics
Small magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features:
- Operating voltage: 5V
- PCB dimension: 3.5 x 2.6cm
- Double red propeller
- Blade length 75mm
- Weight: 6 g
- Quantity:
  1x DC motor
  1x double helix

The LM570R-I laser spirit level is a handy tool used in the construction industry for horizontal and vertical levelling. The 10mW red laser is ideal for projects requiring accurate levelling in a two-dimensional area.

This is a LattePanda (DFR0444) with 2GB RAM and 32GB EMMC memory. The minicomputer is equipped with a 1.92 GHz Intel Cherry Trail Z8350 Quad Core processor. In addition, it has WiFi, Bluetooth 4.0, 2x USB 2.0, 1x USB 3.0, microSD slot, Ethernet port and an additional ATmega32u4 microcontroller with 20 GPIO pins known from Arduino. This version comes with Windows 10 installed, but does not include a Windows 10 activation key.

LCD 2004 Intelligent Reprap Controller 3D Printer can be connected directly to your RAMPS 1.4. All new operations, such as calibration, axis movement can be done only with the smart rotary encoder. You don't need to use your PC. Just use the G-Code layout stored on the SD card.

- It consists of a display of 16 characters and 2 rows
- The display is compatible with the HD44780 controller
- Ideal for projects with ARDUINO
- You can use it with PIC, AVR, STM32 PCF8574 -> the default address 0x20
PCF8574A -> the default address 0x3F
- It can be changed to any between 0x20 and 0x27 depending on whether you have soldiers or not pins A0 A1 A2 Screen LCD Display Screen Blue 1602 + Adapter Board Module IIC/I2C features:
  
- LCD screen, 16 characters and 2 lines
- 5V power
- HD44780 compatible controller
- Backlit blue background, white letters
- Include an adjustable contrast pin
- Dimensions (mm): 80 x 36 x 12 Adapter LCD Display Screen Blue 1602 + Adapter Board Module IIC/I2C features:

1.8 TFT LCD screen with SPI interface and 4 control signals.. It has a resolution of 128x160 pixels. Easily programmable with UNO module, Arduino, Raspberry, Mega2560.

LCD TFT Touch Screen Display 3.2inch 320x240, shield 34 pins.

Lead screw and stainless steel screw set with KFL08 T8-800 for 3D printer. Its shaft coupling diameter is 8mm with pitch of 2mm and has a length of 800mm Lead Screw with Trapezoidal Nut T8 50cm L8 features:
- Type: Trapezoidal screw
- Diameter: 8mm
- Toothing distance: 2mm - Rotation total: 8mm - Lengths: 500 mm Kit contents: 
- Nut 1 unit
- Spindle 1 unit

LED Display Screen Board Matrix 8x8 Common Anode/ Common Cathode Columns Red Dots features:
- Supply voltage of the LED points: 1.8-2.4 VDC
- LED color of the dots: red
- Pin numbers: 16
- Diameter of pins: 0.51mm
- Step between pins: 2.54mm
- Consumption current per segment: 30mA
- Maximum admissible current per segment: 120mA
- Power consumed per segment: 80mW
- Segment numbers (points): 64
- Diameter of a point: 3mm
- Operating temperature: -35°C - + 85°C
- Storage temperature: -35°C - + 85°C
- Screen with common anode connection for the rows and common cathode for the columns
- Screen size: 32x32x8 mm

LED Display Screen Board Matrix 8x8 Common Cathode/Columns Common Anode Red Dots features:
- Supply voltage of the LED points: 1.8-2.4 VDC
- LED color of the dots: red
- Pin numbers: 16
- Diameter of pins: 0.51mm
- Step between pins: 2.54mm
- Consumption current per segment: 30mA
- Maximum admissible current per segment: 120mA
- Power consumed per segment: 80mW
- Segment numbers (points): 64
- Diameter of a point: 3mm
- Operating temperature: -35 ° C - + 85 ° C
- Storage temperature: -35 ° C - + 85 ° C
- Screen with common cathode connection for the rows and common anode for the columns
- Screen size: 32x32x8 mm

This chain has DC5V LEDs that have built-in logic, so it is possible to vary the colour of each LED individually.

WS2811 includes a built-in integrated inside each LED, which allows access to each pixel individually. Black background

Easy programming with Arduino, ESP32, ESP8266, etc. 

Voltage sensor module 0.02445V ~ 25V directly connectable with any version of Raspberry Pi.
LED Matrix 16x8 red MAX7219 Waveshare for Raspberry Pi features:

- Manufacturer: Waveshare
- LED Array: 16x8
- LED Driver: MAX7219
- Voltage operating: 5V
- SPI communication
- Output connector: supports any revision of Raspberry Pi (directly connectable)
- Dimensions: 6.43 × 3.50 × 2.65cm.

The LilyPad Arduino USB is a microcontroller board based on the ATmega32u4.
It has 9 digital input / output pins (of which 4 can be used as PWM outputs and 4 as analog inputs), an 8 MHz resonator, a micro USB connection, a JST connector for a 3.7V LiPo battery and a power button. restart
It contains everything necessary to support the microcontroller; simply connect it to a computer with a USB cable or a battery to start.
The LilyPad Arduino USB differs from previous LilyPad cards in that the ATmega32U4 has built-in USB communication, eliminating the need for a separate USB to serial adapter. This allows the LilyPad Arduino USB to appear on a connected computer as a mouse and keyboard, as well as a virtual serial / COM (CDC) port.

Lilypad Battery Support Button Cell 3V CR2032 features:
- Battery holder for your Lilypad projects
- For 20mm diameter battery type CR2032
- ON / OFF control
- Connection points: 4

This support is a lilypad button to sew clothing or anything else you can dream of.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Button Board features:
- Density of the PCB: 0.8 mm
- Size: 8x16 mm
- 1 LED included

The buzzer plate for Lilypad is used for the development and application of configurations that require a buzzer to indicate, for example, warnings, warnings or as part of the correct operation of your device.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Buzzer features:
- Operating voltage: 5 VDC
- Design of common anode
- PCB density: 0.5 mm
- Density of the buzzer: 20 mm
- Outside diameter: 20 mm

Blue LED.
The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Blue features:
- Operating voltage: 3 - 5 VDC
- Very bright
- Density of the PCB: 0.8 mm
- LED color: blue
- Size: 5.5x12.5 mm
- 1 LED included

This module is a small source of energy, this board was designed to be as small and as indiscreet as possible.
Putting a battery type AAA and operating the power switch, will have a supply of 5 V to power a lilypad circuit.
Use up to 200ma, it is protected against short circuits. This card has AAA battery clips but can use a 1.2V to 5V input, the module increases the voltage up to 5V.
Lithium polymer batteries are an alternative to rechargeable batteries.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Power Supply 5V Step Up with AAA Batteries features:
- Type of batteries connectable: AAA
- Input voltage (of the batteries): from 1.5V to 5V
- Output voltage: 5V

This is a simple slide switch for LilyPad. Use it as a simple On / Off switch, or to control LEDs, buzzers, sensors, etc.
The switches in each panel have a capacity of 4V to 300 mA, but will operate at 5V with a current reduction.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Slide Switch Board 2 Positions Interruptor features:
- Switch two positions: On (ON) / Off (OFF)
- Density of the PCB: 0.8 mm
- Size: 7.75x18.1 mm

Blink any color you need! Use the Tri-Color LED board as a simple indicator, or by pressing the red, green and blue channels, you can create any color. Very bright output.
This is a common anode design: to turn on a channel, you simply need to ground one of the R / G / B pins to illuminate that channel.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Tri-Color LED RGB features:
- Operating voltage: 3 - 5 VDC
- Design of common anode
- Density of the PCB: 0.8 mm
- Outside diameter: 20 mm

The good thing about LiPower is the ability to use rechargeable lithium polymer batteries.
These batteries are smaller, flatter and last much longer than an AAA battery.
Connect a single-cell LiPo battery, turn on the power switch and you will have a 5V supply to power your LilyPad network. It can deliver the current up to 150mA. Protected against the short circuit.
This board has a JST connector, which will be connected to single cell LiPo batteries terminated in JST.
It also has terminals for charging the LiPo battery with LiPo chargers. Each LilyPad was creatively designed to have large connection pads that allow them to sew on clothes.

Lithium Battery 3V CR2032 Button with PCB Pins features:
- 3V battery for horizontal mounting PCB printed circuit
- Quantity: 1 unit
- Diameter: 20mm
- Voltage: 3V
- Capacity: 220mAh

Lithium Battery Holder Button 3V CR1220 THT PCB features:
- Material:
    - Contact: Phosphor Bronze
- Electric:
    - Type: THT
    - Contact Resistance: 30 Milliohms Max
    - Insulation Resistance: 1000 Mega Ohms Min
    - Dielectric Voltage: 500V AC one sec level
    - Operating Temperature: -25 „ƒ - 85 „ƒ
- Suitable for Computer Memory, Power transfer, Communications Power System, PC Application, Armamentarium, Motherboard

Load cell Load Cell Weight Sensor 10kg features:

Load range: 10kg

Operating voltage: 3VDC ~ 14 VDC.

Rated output: 1.0 ± 0.15mV/V.

Repeatability: 0.03% FS

Effect of temperature on output: 0.01% F.S / ° C

Temperature effect on zero: 0.05% F.S / ° C

Load cell Load Cell 20kg features:
- Load range: 20kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S /°C
- Effect of temperature on zero: 0.05% F.S /°C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65
- Cable length: 25 cm
- Size: 75 x 12.7 x 12.7 mm
- Wiring:
* Red: Feeding +
* Black: Source -
* Green: Sign +
* White: Signal -

Load Cell 1 kg Scale Sensor Weight Arduino 
Load cell to measure weight up to 1kg
The transducer measures the deformation of the metal structure and converts it into a few mV. Load cell Load Cell Weight Sensor 1kg features:
- Load range: 1kg
- Operating voltage: 3VDC ~ 14 VDC.
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S / ° C

Load cell Load Cell Weight Sensor 2kg features:
- Load cell to measure weight up to 2kg
- The transducer measures the deformation of the metal structure and converts it into a few mV
- Load range: 2kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S / °C
- Effect of temperature on zero: 0.05% F.S / °C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65

Pressure sensor sometimes called strain gauge. Load cell for measuring weights up to 50kg. The transducer measures the strain of the metal structure and converts it into a few mV.

Load cell Load Cell Weight Sensor 5kg features:
- Load cell to measure weight up to 5kg
- The transducer measures the deformation of the metal structure and converts it into a few mV
- Load range: 5kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S / °C
- Effect of temperature on zero: 0.05% F.S / °C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65

LSC-16 Digital Servo Motor Controller 16 channels features:
- With current limiting protection. The servo output is isolated from the CPU to prevent increased servo current causing damage to the CPU.
- CPU using high performance STM32 single chip microcomputer with ARM Cortex-M3 corer, control High precision 16-channel servo movement, adjustable speed.
- 16M high capacity memory, enough for your use! It can contain 230 action groups! Each action group can hold up to 510 actions!
- Supports online debugging, no need to install any driver by yourself (Install Drivers Automatically).
- 0 ~ 3rd and 12th - 15th servo interface have over current protection! Greatly reducing the risk of burned servo due to locked rotor.

M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features:
- This sensor can be configured as auto Z axis level
- Sensor detection switch inductive proximity LJ12A3-4-Z / BY
- PNP DC6-36V
- Often used for 3D printer bed leveling
- Typical application: printer bed level sensor 3D
- Cylindrical cable type DC 3 cable type (black, brown, blue)
- Inductive sensor type
- PNP NO (Normal Open)
- Detecting Distance 4mm - DC supply voltage 6-36V
- Current output 300mA
- Response frequency 0.5KHz
- Detects iron / aluminum
- Operating temperature -25 ° C at + 55 ° C (Non-freezing condition)
- Head diameter 12 mm
- Size 6.2 x 2cm
- Cable length 100cm

120x M3 Nylon Separator features:
- Hexagonal M3 made of nylon for screws and fastenings on PCB boards, model aircraft, DIY projects
- Can be used in prototyping and robotics projects
- Box dimension: 128x 66x 24mm
- Quantity: 120 units
- Color: white

Magnifying LED Lamp Lens 4 Inch features:
- Diopter: 3D + 12D
- Lens size: 4 inch
- Lens material: glass
- Light source: 15pcs LED
- Standard mount: table base

Magnifying LED Lamp Lens 5 Inch features:
- 80 Leds, diopter 5D
- Lens size: 5 inch
- Lens material: glass
- Light source: 80 pcs LED
- Standard mount: table clamp

DIY Mobile Phone Kit - This  stylish little educational device is an open source mobile phone that you can build yourself. It is compatible with all mobile networks, and its purpose is to motivate people to explore, learn and create something new in a fun and interesting way. Age:+11  

MB-102 Prototype Board + 65x Jumper Cable + Power Module 3.3V 5V Arduino features:
* 65 Male-Male jumper cables:
-Cable lengths: 120mm, 150mm, 200mm, 240mm * MB-102 breadboard:
-830 Connections
-Measures 165x55x8 mm
* Module:
-Input voltage up to 12V
-Maximum current 700mA

Ideal for your electronic projects, Arduino but can also be used with other microcontrollers.

The mClon kit is ideal for building a car with obstacle detection and light tracking. In addition to the platform, the kit contains the basic essentials for building your first robot including the Arduino Uno compatible board, distance sensors and many other components. Check the complete list in the product description

Perfect "Starter Kit Mega XL" to learn programming with arduino the basis of electronics. It allows to build various projects of various complexity, from the easiest ... to the most complicated.
The elements are placed in the box to keep everything in order.
Characteristic:
It includes the following module references:
- 1x R3 REV3 ATmega2560 16U2 Mega2560 + USB 100% Compatible - 1x LED Display Screen Controller Blue Backlight 16x2 1602 HD44780
- 1x Prototype Protoboard MB-102 830 points Arduino
- 1x 74HC595 74595 SN74HC595N 8-Bit Shift Register DIP-16
- 1x LM35 Temperature Sensor LM35DZ TO92
- 2x SW-520D Vibration Tilt Sensor
- 1x fire sensor
- 3x Photoresistor GL5516 LDR
- 4x Push Switch Button B3F Omron Blue Key 12mm

High power digital servo, better precision than the MG995. MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V features:
- Operating voltage: 4.8 V to 7.2 V
- Consumption: 100mA
- Torque max.: 12kg / cm (6V)
- Operating speed: 0.22sec / 60degree (4.8V), 0.19sec/60degree (6V)
- Max. Radio: 180ºC
- Temperature range: 0-55 degrees
- Weight: 55 g
- Cable length: 29cm
- Dimensions: 54 x38x 20 mm
- Servo connector: JR (JR and Futaba adaptable)

For Arduino, Smart Car, Robotics.
Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC with cable conector male features:
- Operating voltage: 1.5V to 6V - Cable 16cm with male connector - DC current: 350mA - Torque max.: 15g / cm
- Max speed: 12000rpm
- Weight: 16.5 g

Tower Pro Micro Servo 9g SG90 features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

This module is a 2-channel DC 7-12 VDC power supply for MB102 breadboards.
Each channel has its switch for configure the output voltage to 3.3V or 5V.
Its 3x2 male connectors allow it to be connected to the breadboard in a very simple way without soldering. Micro USB Interface Power Supply DC 7-12 VDC features:
- Operating voltage: DC 7-12 V
- Power display LED
- 1 Jack Female connector 2.1 mm to supply
- 1 AMS1117 3.3V regulator
- 1 AMS1117 5V regulator
- 4 3x2 connectors
- 1 5V micro USB female outlet
- Size: 5.5x3.5x1.5 cm

IOBIT expansion board for the micro:bit minicomputer. Allows connection to all minicomputer outputs via a pin strip.  

Micro:bit Tinker Kit - Create a variety of octopus sensors thanks to the Tinker kit and the many project tutorials to help you create dozens of amazing digital maker projects. Note: the micro:bit board is not included, you can buy it separately. All modules have convenient connectors to use them and no soldering is required.

12V electric drill, with ON/OFF switch with 2 grinding tips, 2 burrs, 4 nozzles

Characteristic: - Operating voltage: 3-6V
- Max flow: 80-120 l / h
- Maximum pumping height: 40-110cm
- Continuous working time of 500 hours
- Cable length: 20cm
- Inside outlet diameter: 5 mm
- Outside outlet diameter: 7.5 mm - Dimensions: 45mm x 23mm x 30mm

  Mini voltmeter with LED display 7 red 3-digit segments.
Simply connect the positive and the negative to turn it on and measure the voltage.   Mini voltmeter with LED display 7 blue segments 3 digits 3.5-30 VDC - 1% features:
  - Operating voltages (measurement): 3.5 - 30 VDC,
- Color of the LED segments: blue
- Update speed: approx. 500ms,
- Accuracy of the measurement: ± 1%,
- No need power supply: it is powered with the measured voltage,
- Cable length included: 10cm,
- Size: 30x12x9mm.

Mini voltmeter with LED display 7 green 3-digit segments.
Simply connect the positive and the negative to turn it on and measure the voltage.
Mini voltmeter with LED display 7 green segments 3 digits 3.5-30 VDC - 1% features:
- Operating voltages (measurement): 3.5 - 30 VDC,
- Color of the LED segments: green,
- Update speed: approx. 500ms,
- Accuracy of the measurement: ± 1%,
- No need power supply: it is powered with the measured voltage,
- Cable length included: 10cm,
- Size: 30x12x9mm.

Mini voltmeter with LED display 7 red 3-digit segments.
Simply connect the positive and the negative to turn it on and measure the voltage.
Mini voltmeter with LED display 7 red segments 3 digits 3.5-30 VDC - 1% features:
- Operating voltages (measurement): 3.5 - 30 VDC,
- Color of the LED segments: red,
- Update speed: approx. 500ms,
- Accuracy of the measurement: ± 1%,
- No need power supply: it is powered with the measured voltage,
- Cable length included: 10cm,
- Size: 30x12x9mm.

Auto shut down module for MKS GEN L SKR V1.3 

MKS PWC automatically turning off after the printing. It helps in the cases like the unexpected power off or you have to leave during the printing, and other similar issues. 

The integrated mainboard driver MKS-GEN L V1.0 for 3D printer has been developed by Makerbase to optimize existing problems on the open source controller board such as Ramps 1.4.
This product offers more flexible options for users.
MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 features:
- Mega2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.
- Supports a variety of step-by-step drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change stepper motors and motors that users like.
- Reserve the signal from the external controller, available to connect an external high current driver to drive stepper motors 57 and 86.
se high quality MOSFET, better cooling and more stable.

Assemble your personalised paper lamp, and discover the magic of this electrically conductive paint. Stimulate your creativity and your manual skills or those of the youngest members of the family by assembling this curious and modern lamp with 3 models available: touch lamp, adjustable light lamp and proximity lamp.

As easy as pressing the tube, drawing the painting lines, folding the template and turning it on. No need for programming, tools or special skills.

The electric painting lamp kit is the perfect gift to bring a little more light into your life or someone else's.

This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.
The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features:
- 1 logical step of the input voltage VD: 5 VDC
- Control of the input voltage VS and control by pulse width modulation:
      - VIN input: 6 - 12 VDC
      - PWRIN input: 4.8 - 35 VDC
- Logic current flow: Iss <36m A
- Operation current management: Io <2 A
- Maximum power dissipation 25W (T = 75 ° C)
- Input of the control signal:

Mosfet 24V 5A IRF520 PWM controller features:
- The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater.
- The built-in IRF520 N-MOSFET transistor
- Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI)
- Charging voltage: 0-24V
- Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point)
- 60W max power (more than 10W must be equipped with a heat sink)
- Terminalblock connectors
- LED indicating the presence of power
- Dimensions: 33x24mm

It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 4.28 kg/cm. It comes with a 1m cable. We have the best stepper motors at the best prices! 

It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 28.5 kg/cm. Comes with a 50 cm cable. We have the best stepper motors at the best prices! Perfect for CNC machines!

MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime.

NEZHA inventor kit for micro:bit develop your imagination and creativity with the Nehza 36-in-1 kit for micro:bit.

The UNI-T UT300H temperature meter, which uses the latest technology, enables temperature measurements in the range of 32°C-42.9°C. The high accuracy of the device enables fast and accurate monitoring of body temperature as well as other environmental elements, e.g. objects, food, liquids, etc.

The UNI-T UT300H temperature meter, which uses the latest technology, enables temperature measurements in the range of 32°C-42.9°C. The high accuracy of the device enables fast and accurate monitoring of body temperature as well as other environmental elements, e.g. objects, food, liquids, etc.

- This module includes PA preamplifier and LNA (Low-noise amplifier)
- Comes with the SMA antenna for 2.4GHz (2dB)
- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer
- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features:
* Based on chip NRF24L01 +
* Free band: 2.4GHz ISM
* Speed: 250kbps, 1Mbps, 2Mbps
* Work current
- Reception: 45 mA
- Transmission: 115 mA (4.2uA -sleep mode)
* Receiving sensitivity:
-104dB 250kbps
- 95dB 1Mbps
- 92dB 2Mbps
* SPI interface

The assembled Original Prusa i3 MK3S+ is the latest version of the MK3 3D printer line. It has a new SuperPINDA probe for improved first layer calibration, high quality bearings have been added and a number of useful design tweaks have been made. Gratis - 1kg Prusa Orange PETG Filament and Textured Sheet with Double Sided PEI Powder Coating

- Pantalla LCD TFT 240x320 pixels
- 262.000 posibles colores (18 bit)
- Pixel: RGB vertical stripe
- Controlador ILI9341
- Interface SPI
- 8 bit interfaz digital, 4 bit líneas de control
- Pantalla táctil resistiva 4
- wires
- Ideal para proyectos con ARDUINO, Uno R3, MEGA2560 Enlaces útiles : Cableado de la pantalla LCD TFT 2.4 SPI
- Conectar la pantalla LCD TFT 2.4 SPI con el módulo UNO Visualizar gráficos y textos en la pantalla LCD TFT 2.4 SPI Programar una calculadora táctil en la pantalla LCD TFT 2.4 SPI

Premium Bobina para Impresora 3D

Pink 3D-pen for ABS / PLA filaments features:
This 3D pen is suitable for 1.75m ABS or PLA filaments.
It includes an LCD screen that allows you to read the temperature, speed and filament.
It also comes with button controls to control the extrusion speed.
You can use this powerful 3D pen to draw, draw or trace objects on the paper. Pink 3D-pen for ABS / PLA filaments features:
- Input voltage: 12V,
- Current consumption: 2A,
- Nozzle diameter: 0.7mm - Heating temperature: 160-230 degrees adjustable,
- Pen color: pink,
- Random color filaments,
- Includes PLA filament and 100-240 VAC / 50 Hz power - 12VDC / 2A,
- Recommended for adults and children 8 years and older.

The pixel board is equipped with a WS2812 that is actually RGB LED with a WS2811 built into the LED.
Several of these individual sessions can be chained together to form a screen or an addressable string.
Each LilyPad is creatively designed to have large connecting pads so that they can be sewn on clothes. Pixel Board WS2812 for Lilypad features:
- Use the WS2812S chip
- RGB color lights
- Each LED can be controlled individually
- You only need one control line and two power cables
- Arduino libraries and routines available
- Density of the PCB: 0.8 mm
- Size: 20x3 mm

Premium Bobina para Impresora 3D

Premium Bobina para Impresora 3D

Premium Bobina para Impresora 3D

Premium Bobina para Impresora 3D

Premium Bobina para Impresora 3D

Premium Bobina para Impresora 3D