SD Card Module Reader The SD card reader module is a simple solution for transferring data to and from a standard SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.SD Card Module Reader features:- Supply voltage: 3.3V or 5V - Interface: SPI 3.3V- Dimensions: 30mm x 50mm x 12mm Code M0023 Available Price €0.82
4x AA 6V battery holder with DC connector 4x AA 6V battery holder with DC connector features: - Cable 12cm long - Measurements 62x56x 16mm - Battery length max 50mm - Compatible batteries ( LR06, R06, MN1500, AM3, UM3, HP7) Code PP004 Available Price €1.48
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.30
Transparent Box for W1209 DIY Transparent Box for W1209 DIY features: For W1209 Thermostat DC 12V temperature controller Code M0107 Available Price €2.19
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.09
Raspberry Pi Pico The first Raspberry microcontroller with the proprietary RP2040 chip and a dual-core Arm Cortex-M0+, the Foundation's cost-effective yet highly flexible solution. Designed for high performance and with a high degree of digital interfaces. Programming in C/ C++ and MicroPython. Code RA124 Available Price €4.12
USBASP Atmega8 AVR Programmer Atmega128 Arduino compatible Adapter Cable Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1 - LED status indicators - Transmission speed: 5kB / s - Fuse protector against possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦ Code B0029 Available Price €5.45
NDIR CO2 Sensor MH-Z14A Carbon dioxide detection MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime. Code S0149 Available Regular price €24.75 -€6.00 Price €18.75
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €6.53
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €5.78
LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board- Put the screen on the shield and you can connect it directly to the Arduino UNO- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen Code P0004 Available Price €5.70
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €6.53
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2inch 320x240, shield 34 pins. Code P0107 Available Regular price €14.79 -€1.41 Price €13.38
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 4 control signals.. It has a resolution of 128x160 pixels. Easily programmable with UNO module, Arduino, Raspberry, Mega2560. Code P0208 Available Regular price €7.40 -€3.00 Price €4.40
LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD features:- LCD screen TFT 240x320 pixels- Power 2.8-3.3V- 262,000 possible colors (18 bit)- 8/16 bit parallel bus digital interface- LCD Controller: ILI9325- Touch screen controller: XPT2046- Touchscreen, resistive touch screen- Manual use or with any type of pointer- SD card reader- Connector: 2 x 20 pins 2.54mm- Dimensions PCB 75x55 mm- Dimensions LCD 59x42 mm- Ideal for projects with ARDUINO Uno Mega, AVR, STM Code P0005 Last items in stock Price €8.26
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €7.40
2.4 inch TFT LCD screen 240x320 SPI LCD TFT Display Module 240x320 2.4 SPI features: - LCD screen TFT 240x320 pixels- 262,000 possible colors (18 bit)- Pixel: RGB vertical band- Driver ILI9341- SPI interface- 8-bit digital interface, 4-bit control lines- Resistive touch screen 4 - cables- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Helpful Links: Wiring of the TFT LCD screen 2.4 SPI - Connect the TFT 2.4 SPI LCD screen with the UNO module Display graphics and texts on the LCD TFT screen 2.4 SPI Program a touch calculator on the LCD screen TFT 2.4 SPI Code P0001 Available Regular price €9.88 -€2.40 Price €7.48
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2 inch 320x240. Shied 40pins. Code P0165 Available Price €13.97
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €6.53
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €5.78
LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board- Put the screen on the shield and you can connect it directly to the Arduino UNO- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen Code P0004 Available Price €5.70
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €6.53
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2inch 320x240, shield 34 pins. Code P0107 Available Regular price €14.79 -€1.41 Price €13.38
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 4 control signals.. It has a resolution of 128x160 pixels. Easily programmable with UNO module, Arduino, Raspberry, Mega2560. Code P0208 Available Regular price €7.40 -€3.00 Price €4.40
LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD features:- LCD screen TFT 240x320 pixels- Power 2.8-3.3V- 262,000 possible colors (18 bit)- 8/16 bit parallel bus digital interface- LCD Controller: ILI9325- Touch screen controller: XPT2046- Touchscreen, resistive touch screen- Manual use or with any type of pointer- SD card reader- Connector: 2 x 20 pins 2.54mm- Dimensions PCB 75x55 mm- Dimensions LCD 59x42 mm- Ideal for projects with ARDUINO Uno Mega, AVR, STM Code P0005 Last items in stock Price €8.26
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €7.40
2.4 inch TFT LCD screen 240x320 SPI LCD TFT Display Module 240x320 2.4 SPI features: - LCD screen TFT 240x320 pixels- 262,000 possible colors (18 bit)- Pixel: RGB vertical band- Driver ILI9341- SPI interface- 8-bit digital interface, 4-bit control lines- Resistive touch screen 4 - cables- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Helpful Links: Wiring of the TFT LCD screen 2.4 SPI - Connect the TFT 2.4 SPI LCD screen with the UNO module Display graphics and texts on the LCD TFT screen 2.4 SPI Program a touch calculator on the LCD screen TFT 2.4 SPI Code P0001 Available Regular price €9.88 -€2.40 Price €7.48
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2 inch 320x240. Shied 40pins. Code P0165 Available Price €13.97