Protoboard Breadboard 400 points for Arduino It can be used to work with AVR, ARM, PIC microcontrollers, Arduino modules and to work with self-designed prototypes. Arduino Protoboard Breadboard 400 points features: -400 Connections -Linkable with other Plates -Base with adhesive to attach it to the work surface -Measures 82x55x8 mm Code PB002 Available Price €1.90
TCRT5000 Module 3.5cm IR infrared sensor The optical (reflective) module sensor with LM393 comparator, which detects obstacles with high accuracy. The ideal detector for obstacle detection for the installation of intelligent robots.TCRT5000: reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The transmitter is an infrared LED and the receiver is a phototransistor. The sensor allows the detection of an object at a distance of up to 3.5 cm from the white paper and 1 cm from the person's finger. Code S0138 Available Price €1.69
Rotary Encoder EC11 with Push Button Switch It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0. Code M0012 Available Price €1.39
DS18B20 Submersible Probe Sensor Temperature Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.DS18B20 Submersible Probe Sensor Temperature features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Red Vcc - Yellow digital output- Inocidable steel- Cable length: 1m Code S0019 Available Price €2.39
Banana Plug Cable Multimeter pack 5 colors Banana-banana plug cable for multimeter. Good quality tester cable. Code K0052 Available Price €7.99
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €8.95
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €2.45
Resistor 1K Ohm 5% 0,25W 1/4W Resistor 1K Ohm 5% 0,25W 1/4W features:-1 unit - 1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0076 Available Price €0.09
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €9.90
2.4 inch TFT LCD screen 240x320 SPI LCD TFT Display Module 240x320 2.4 SPI features: - LCD screen TFT 240x320 pixels- 262,000 possible colors (18 bit)- Pixel: RGB vertical band- Driver ILI9341- SPI interface- 8-bit digital interface, 4-bit control lines- Resistive touch screen 4 - cables- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Helpful Links: Wiring of the TFT LCD screen 2.4 SPI - Connect the TFT 2.4 SPI LCD screen with the UNO module Display graphics and texts on the LCD TFT screen 2.4 SPI Program a touch calculator on the LCD screen TFT 2.4 SPI Code P0001 Available Price €13.95
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €9.90
LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board- Put the screen on the shield and you can connect it directly to the Arduino UNO- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen Code P0004 Available Price €7.90
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €8.95
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €7.99
LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD features:- LCD screen TFT 240x320 pixels- Power 2.8-3.3V- 262,000 possible colors (18 bit)- 8/16 bit parallel bus digital interface- LCD Controller: ILI9325- Touch screen controller: XPT2046- Touchscreen, resistive touch screen- Manual use or with any type of pointer- SD card reader- Connector: 2 x 20 pins 2.54mm- Dimensions PCB 75x55 mm- Dimensions LCD 59x42 mm- Ideal for projects with ARDUINO Uno Mega, AVR, STM Code P0005 Available Price €9.99
IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features: - Based on the PCF8574A chip - Power: 5V - Supports I2C Protocol - A potentiometer for regulate contrast - Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL - Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 Code P0008 Available Price €1.95
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2 inch 320x240. Shied 40pins. Code P0165 Backorder Price €22.90
Pantalla LCD TFT 2.4 pulgadas 240x320 SPI - Pantalla LCD TFT 240x320 pixels- 262.000 posibles colores (18 bit)- Pixel: RGB vertical stripe- Controlador ILI9341 - Interface SPI - 8 bit interfaz digital, 4 bit líneas de control- Pantalla táctil resistiva 4 - wires- Ideal para proyectos con ARDUINO, Uno R3, MEGA2560 Enlaces útiles : Cableado de la pantalla LCD TFT 2.4 SPI - Conectar la pantalla LCD TFT 2.4 SPI con el módulo UNO Visualizar gráficos y textos en la pantalla LCD TFT 2.4 SPI Programar una calculadora táctil en la pantalla LCD TFT 2.4 SPI Code P0110 Available Price €9.60
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Backorder Price €9.90
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €9.90
2.4 inch TFT LCD screen 240x320 SPI LCD TFT Display Module 240x320 2.4 SPI features: - LCD screen TFT 240x320 pixels- 262,000 possible colors (18 bit)- Pixel: RGB vertical band- Driver ILI9341- SPI interface- 8-bit digital interface, 4-bit control lines- Resistive touch screen 4 - cables- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Helpful Links: Wiring of the TFT LCD screen 2.4 SPI - Connect the TFT 2.4 SPI LCD screen with the UNO module Display graphics and texts on the LCD TFT screen 2.4 SPI Program a touch calculator on the LCD screen TFT 2.4 SPI Code P0001 Available Price €13.95
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €9.90
LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board- Put the screen on the shield and you can connect it directly to the Arduino UNO- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen Code P0004 Available Price €7.90
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €8.95
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €7.99
LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD features:- LCD screen TFT 240x320 pixels- Power 2.8-3.3V- 262,000 possible colors (18 bit)- 8/16 bit parallel bus digital interface- LCD Controller: ILI9325- Touch screen controller: XPT2046- Touchscreen, resistive touch screen- Manual use or with any type of pointer- SD card reader- Connector: 2 x 20 pins 2.54mm- Dimensions PCB 75x55 mm- Dimensions LCD 59x42 mm- Ideal for projects with ARDUINO Uno Mega, AVR, STM Code P0005 Available Price €9.99
IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features: - Based on the PCF8574A chip - Power: 5V - Supports I2C Protocol - A potentiometer for regulate contrast - Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL - Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 Code P0008 Available Price €1.95
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2 inch 320x240. Shied 40pins. Code P0165 Backorder Price €22.90
Pantalla LCD TFT 2.4 pulgadas 240x320 SPI - Pantalla LCD TFT 240x320 pixels- 262.000 posibles colores (18 bit)- Pixel: RGB vertical stripe- Controlador ILI9341 - Interface SPI - 8 bit interfaz digital, 4 bit líneas de control- Pantalla táctil resistiva 4 - wires- Ideal para proyectos con ARDUINO, Uno R3, MEGA2560 Enlaces útiles : Cableado de la pantalla LCD TFT 2.4 SPI - Conectar la pantalla LCD TFT 2.4 SPI con el módulo UNO Visualizar gráficos y textos en la pantalla LCD TFT 2.4 SPI Programar una calculadora táctil en la pantalla LCD TFT 2.4 SPI Code P0110 Available Price €9.60