Lilypad Matching Conductive Sewing Thread Wearable This thread is designed to be used in Wearables projects because it provides a very firm grip on the fabric to be sewn.What differentiates this thread from another thread is the fact that it is actually spun from this stainless steel fiber. This means that while it may not be easy to weld since it is steel, it also does not burn when you touch it with a soldering iron.It is suitable for sewing machine (like a bobbin thread) it is particularly tense, which means that it firmly grasps the fabric and is not slippery. Lilypad Matching Conductive Sewing Thread Wearable features:- Stainless steel fibers- Resistance: 700 Ohm / m- Thin and strong thread- Includes 1 meter of wire Code M0149 Available Price €0.83
Lilypad Slide Switch Board 2 Positions Interruptor This is a simple slide switch for LilyPad. Use it as a simple On / Off switch, or to control LEDs, buzzers, sensors, etc.The switches in each panel have a capacity of 4V to 300 mA, but will operate at 5V with a current reduction.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Slide Switch Board 2 Positions Interruptor features: - Switch two positions: On (ON) / Off (OFF)- Density of the PCB: 0.8 mm- Size: 7.75x18.1 mm Code M0141 Available Regular price €1.64 -€0.50 Price €1.14
SIM808 GPRS GSM GPS Bluetooth SIM Quadband SIM808 GPRS GSM GPS Bluetooth SIM Quadband features: - SIM card SIM808 GPRS GSM GPS Bluetooth SIM - Supply voltage range: 3.4-4.4V - Four bands GSM 850/900/1800 / 1900MHz - GPRS multi-slot class 12/10 - GPRS mobile station class B - According to GSM phase 2/2 + - Class 4 (2 W at 850/900 MHz) - Class 1 (1W at 1800 / 1900MHz) - Control by AT commands (3GPP TS 27.007.27.005 and enhanced AT Commands from SIM Com) - Operating temperature: -40 to + 85 ° C - PCB dimension: 38x38mm - GPS sensitivity - Tracking: -165dBm Cold start Sensitivity - Cold start: -147dBm - Time to first solution - Cold start: 30 s - Start to warm up: 28s - Already hot: 1s - Accuracy Code W0069 Available Regular price €16.44 -€3.00 Price €13.44
Lilypad Tri-Color LED RGB Blink any color you need! Use the Tri-Color LED board as a simple indicator, or by pressing the red, green and blue channels, you can create any color. Very bright output.This is a common anode design: to turn on a channel, you simply need to ground one of the R / G / B pins to illuminate that channel.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Tri-Color LED RGB features: - Operating voltage: 3 - 5 VDC- Design of common anode- Density of the PCB: 0.8 mm- Outside diameter: 20 mm Code M0143 Available Regular price €1.23 -€0.30 Price €0.93
DS1302 Real Time Clock RTC Module AVR ARM PIC Ideal for projects with ARDUINO you can use it with PIC, AVR, STM32.Provides seconds, minutes, time and date, calendar up to the year 2100.DS1302 Real Time Clock RTC Module AVR ARM PIC features:- Chip: DS1302- Power supply: 2V-5V- Operating current: <2mA- Dimensions: 44 x23 x 8mm- Battery not included in this sale- Connect the RTC to your ArduinoVCC -> Arduino + 3.3VGND -> Arduino GndCLK -> (SCLK_PIN)DAT -> (IO_PIN)RST -> (CE_PIN) Code M0014 Available Price €1.62
Lilypad LED Red LED of red color.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Red features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: red- Size: 5.5x12.5 mm- 1 LED included Code M0138 Last items in stock Price €0.82
Lilypad Button Board This support is a lilypad button to sew clothing or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Button Board features: - Density of the PCB: 0.8 mm- Size: 8x16 mm- 1 LED included Code M0142 Available Regular price €0.82 -€0.20 Price €0.62
Black box with cooling fan and heatsinks for Raspberry Pi 4 model B All ports and slots on the case can perfectly match Raspberry Pi 4 Model B. Code RA092 Available Price €4.62
Lilypad Battery Support Button Cell 3V CR2032 Lilypad Battery Support Button Cell 3V CR2032 features: - Battery holder for your Lilypad projects - For 20mm diameter battery type CR2032 - ON / OFF control - Connection points: 4 Code M0072 Available Regular price €3.30 -€1.00 Price €2.30
Lilypad Slide Switch Board 2 Positions Interruptor This is a simple slide switch for LilyPad. Use it as a simple On / Off switch, or to control LEDs, buzzers, sensors, etc.The switches in each panel have a capacity of 4V to 300 mA, but will operate at 5V with a current reduction.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Slide Switch Board 2 Positions Interruptor features: - Switch two positions: On (ON) / Off (OFF)- Density of the PCB: 0.8 mm- Size: 7.75x18.1 mm Code M0141 Available Regular price €1.64 -€0.50 Price €1.14
Lilypad Button Board This support is a lilypad button to sew clothing or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Button Board features: - Density of the PCB: 0.8 mm- Size: 8x16 mm- 1 LED included Code M0142 Available Regular price €0.82 -€0.20 Price €0.62
Lilypad LED Blue Blue LED.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Blue features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: blue- Size: 5.5x12.5 mm- 1 LED included Code M0137 Available Regular price €0.82 -€0.20 Price €0.62
Lilypad Buzzer The buzzer plate for Lilypad is used for the development and application of configurations that require a buzzer to indicate, for example, warnings, warnings or as part of the correct operation of your device.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Buzzer features: - Operating voltage: 5 VDC- Design of common anode- PCB density: 0.5 mm- Density of the buzzer: 20 mm- Outside diameter: 20 mm Code M0144 Available Regular price €1.65 -€0.50 Price €1.15
Lilypad LED Red LED of red color.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Red features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: red- Size: 5.5x12.5 mm- 1 LED included Code M0138 Last items in stock Price €0.82
Lilypad LED Green LED green.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Green features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: green- Size: 5.5x12.5 mm- 1 LED included Code M0139 Last items in stock Price €0.82
Lilypad Tri-Color LED RGB Blink any color you need! Use the Tri-Color LED board as a simple indicator, or by pressing the red, green and blue channels, you can create any color. Very bright output.This is a common anode design: to turn on a channel, you simply need to ground one of the R / G / B pins to illuminate that channel.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Tri-Color LED RGB features: - Operating voltage: 3 - 5 VDC- Design of common anode- Density of the PCB: 0.8 mm- Outside diameter: 20 mm Code M0143 Available Regular price €1.23 -€0.30 Price €0.93
LiPower Battery Booster Module 5V Output Lilypad The good thing about LiPower is the ability to use rechargeable lithium polymer batteries.These batteries are smaller, flatter and last much longer than an AAA battery.Connect a single-cell LiPo battery, turn on the power switch and you will have a 5V supply to power your LilyPad network. It can deliver the current up to 150mA. Protected against the short circuit.This board has a JST connector, which will be connected to single cell LiPo batteries terminated in JST.It also has terminals for charging the LiPo battery with LiPo chargers. Each LilyPad was creatively designed to have large connection pads that allow them to sew on clothes. Code M0148 Available Regular price €6.60 -€1.00 Price €5.60
Pixel Board WS2812 for Lilypad The pixel board is equipped with a WS2812 that is actually RGB LED with a WS2811 built into the LED.Several of these individual sessions can be chained together to form a screen or an addressable string.Each LilyPad is creatively designed to have large connecting pads so that they can be sewn on clothes. Pixel Board WS2812 for Lilypad features:- Use the WS2812S chip- RGB color lights- Each LED can be controlled individually- You only need one control line and two power cables- Arduino libraries and routines available- Density of the PCB: 0.8 mm- Size: 20x3 mm Code M0146 Available Regular price €5.61 -€2.00 Price €3.61
Lilypad Battery Support Button Cell 3V CR2032 Lilypad Battery Support Button Cell 3V CR2032 features: - Battery holder for your Lilypad projects - For 20mm diameter battery type CR2032 - ON / OFF control - Connection points: 4 Code M0072 Available Regular price €3.30 -€1.00 Price €2.30
Lilypad Slide Switch Board 2 Positions Interruptor This is a simple slide switch for LilyPad. Use it as a simple On / Off switch, or to control LEDs, buzzers, sensors, etc.The switches in each panel have a capacity of 4V to 300 mA, but will operate at 5V with a current reduction.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Slide Switch Board 2 Positions Interruptor features: - Switch two positions: On (ON) / Off (OFF)- Density of the PCB: 0.8 mm- Size: 7.75x18.1 mm Code M0141 Available Regular price €1.64 -€0.50 Price €1.14
Lilypad Button Board This support is a lilypad button to sew clothing or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Button Board features: - Density of the PCB: 0.8 mm- Size: 8x16 mm- 1 LED included Code M0142 Available Regular price €0.82 -€0.20 Price €0.62
Lilypad LED Blue Blue LED.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Blue features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: blue- Size: 5.5x12.5 mm- 1 LED included Code M0137 Available Regular price €0.82 -€0.20 Price €0.62
Lilypad Buzzer The buzzer plate for Lilypad is used for the development and application of configurations that require a buzzer to indicate, for example, warnings, warnings or as part of the correct operation of your device.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Buzzer features: - Operating voltage: 5 VDC- Design of common anode- PCB density: 0.5 mm- Density of the buzzer: 20 mm- Outside diameter: 20 mm Code M0144 Available Regular price €1.65 -€0.50 Price €1.15
Lilypad LED Red LED of red color.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Red features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: red- Size: 5.5x12.5 mm- 1 LED included Code M0138 Last items in stock Price €0.82
Lilypad LED Green LED green.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Green features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: green- Size: 5.5x12.5 mm- 1 LED included Code M0139 Last items in stock Price €0.82
Lilypad Tri-Color LED RGB Blink any color you need! Use the Tri-Color LED board as a simple indicator, or by pressing the red, green and blue channels, you can create any color. Very bright output.This is a common anode design: to turn on a channel, you simply need to ground one of the R / G / B pins to illuminate that channel.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Tri-Color LED RGB features: - Operating voltage: 3 - 5 VDC- Design of common anode- Density of the PCB: 0.8 mm- Outside diameter: 20 mm Code M0143 Available Regular price €1.23 -€0.30 Price €0.93
LiPower Battery Booster Module 5V Output Lilypad The good thing about LiPower is the ability to use rechargeable lithium polymer batteries.These batteries are smaller, flatter and last much longer than an AAA battery.Connect a single-cell LiPo battery, turn on the power switch and you will have a 5V supply to power your LilyPad network. It can deliver the current up to 150mA. Protected against the short circuit.This board has a JST connector, which will be connected to single cell LiPo batteries terminated in JST.It also has terminals for charging the LiPo battery with LiPo chargers. Each LilyPad was creatively designed to have large connection pads that allow them to sew on clothes. Code M0148 Available Regular price €6.60 -€1.00 Price €5.60
Pixel Board WS2812 for Lilypad The pixel board is equipped with a WS2812 that is actually RGB LED with a WS2811 built into the LED.Several of these individual sessions can be chained together to form a screen or an addressable string.Each LilyPad is creatively designed to have large connecting pads so that they can be sewn on clothes. Pixel Board WS2812 for Lilypad features:- Use the WS2812S chip- RGB color lights- Each LED can be controlled individually- You only need one control line and two power cables- Arduino libraries and routines available- Density of the PCB: 0.8 mm- Size: 20x3 mm Code M0146 Available Regular price €5.61 -€2.00 Price €3.61