MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3
  • MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3
  • MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3
  • MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3
  • MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3

MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3

I0143

The integrated mainboard driver MKS-GEN L V1.0 for 3D printer has been developed by Makerbase to optimize existing problems on the open source controller board such as Ramps 1.4.
This product offers more flexible options for users.
MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 features:
- Mega2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.
- Supports a variety of step-by-step drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change stepper motors and motors that users like.
- Reserve the signal from the external controller, available to connect an external high current driver to drive stepper motors 57 and 86.
se high quality MOSFET, better cooling and more stable.

Makerbase
5905323237353
Add to wish list

MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 description


The integrated mainboard driver MKS-GEN L V1.0 for 3D printer has been developed by Makerbase to optimize existing problems on the open source controller board such as Ramps 1.4.
This product offers more flexible options for users.

MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 features:


- Mega2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.
- Supports a variety of step-by-step drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change stepper motors and motors that users like.
- Reserve the signal from the external controller, available to connect an external high current driver to drive stepper motors 57 and 86.
- Use high quality MOSFET, better cooling and more stable.
- Use a specific power chip, support 12V-24V power input and solve the problems of chip heating and lack of power.
- The stable and reliable filter circuit greatly reduces the interference and avoids blockages as possible in the printing process.
- Use the CH340 serial port chip, install the unit more easily than 16U2.
- Run the Marlin firmware, the configuration is completely identical to that of Ramps 1.4, and is available to directly replace the Ramps 1.4.
- Support Ramps 1.4, 2004LCD, 12864LCD, TFT28 and TFT32.
- Available for the 24V input, the hot bed current can be reduced to 1/4 with the same power of the system, which effectively solves the problem that the MOSFET of the heated bed is heated.
- The X axis, Y axis and Z axis with different color terminal control stepper motors and limit switches, which is convenient for wiring.
- Connect the step-by-step controllers according to the different color terminals, which decreases the probability of recoil and avoids the damage of the controller board.

Customers who bought this product also bought

A4988 + RepRap Radiator

A4988 + RepRap Radiator features:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

I0023

Price €1.57

Fan 12V 2x Cables 3D Reprap Printer

Fan 12V 2x Cables 3D Reprap Printer features:
- For Prusa RepRap 3D Printer
- Voltage: 12V
- Consumption: 90mA - Speed: 7000rpm ± 10%
- Noise level: 25dB ± 10%
- Screw diameter: 3.5mm
- Service Life Time: 35000 hours
- Operating temperature: -10 ° C to 65 ° C
- Cable length: 28cm
- Dimensions: 30mm x 30mm x 10mm

I0045

Price €1.31

MPU-6050 Accelerometer Module + Gyroscope 3

Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:
- Chip: MPU-6050
- Power supply: 3V-5V
- Operating current: 5mA
- Communication: I2C
- 16-bit analog-digital converter on all axes
- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)
- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)
- Dimensions: 14 x 21 x 1.3mm
- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin)

M0017

Price €3.55

Fan 12V 2x Cable 50x50x15 3D Printer Reprap

Fan 12V 2x Cable 50x50x15 3D Printer Reprap features:
- Voltage: 12V
- Speed: 7000rpm ± 10%
- Screw diameter: 4.5mm
- Time lifespan: 50,000 hours
- Operating temperature: -10 ° C to 70 ° C
- Cable length: 28cm
- Dimensions: 50mm x 50mm x 10mm

I0120

Price €1.73

Raspberry Pi 4 Modelo B 4GB RAM

The Raspberry Pi 4 Model B is the latest product in the Raspberry Pi family of computers. This product is in the 4GB RAM version, with 2GB (B0068) and 1GB (B0067) versions also on offer.

B0069

Price €49.50
€26.36
Save €2.00 €24.36

24,36 tax excl.

1
Last 7 items
Regular price €26.36 Price €24.36

Order until 4pm we will send today
30 days return