Ramps 1.6 Reprap - Arduino Mega Pololu Shield

CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features:
- Content:
* 1x UNO R3 CH340 Compatible with Arduino
* 1x CNC Shield V3
* 4x A4988 Drivers
* 4x Heatsinks for A4988
* Jumpers

It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations.
Characteristic:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 45 V
- Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32
- Factory soldered temples
- 4-layer PCB, 2 oz. Copper for improved heat dissipation
- Short-circuit and overtemperature protection - Use potentiometer to adjust the current
- Measurements: 20x16x12 mm

A4988 + RepRap Radiator features:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

Router TB6560 1 Axis 3A Stepper Motor Driver Board features:
- Minimum operating voltage: 10 V
- Maximum operating voltage: 35 V (24V recommended)
- Maximum current: ± 3 A
- Stepper motor · two phases · four phases
- Resolution of microsteps: full, 1/2, 1/8, and 1/16
- PCB measurements: 75x50 mm
- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board
- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply
- 6N137 high speed optical coupling guarantees high speed without losing steps
- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent
- Protection circuit to ensure optimal performance
- Maximum nominal output: 3 A, peak 3.5A

The kit contains the Mega board, the Ramps 1.4 shield and 4 A4988 controllers with heatsinks.

Feature of 3D Zum shield: - Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- Content:
       - 1x Zum Shield 3D
       - 1x UNO R3 Compatible Arduino
       - 1x Controller A4988
       - 1x Male pin strip
       - 1x Heatsink for A4988
       - 1x USB cable
       - Jumpers

The output current of this controller is infinitely adjustable to meet the various requirements of your application.
It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.
Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.
Its large heat sink allows good quality cooling.
The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features:
  - Operating voltage DC 10V-45V
- Maximum nominal output: 4.5 A
- DC32V switching power is recommended
- 6N137 high speed optical coupling, ensure high speed without losing step

Stepstick A4988 controller
Driver for stepper motors
Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield
A4988 + Stepstick Radiator Stepper Motor Reprap features:

- Minimum operating voltage: 8 V
- Operating voltage maximum: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers

Zum Scanner Expansion Board 3D DIY features:
- Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- 3D Scanner Ciclop is an open source project created by bq
- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser
- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board