Soldering Aid Kit Welding Tools Soldering Aid Kit Welding Tools features: - Variety of applications for precision work- To meet the requirements of welding operation of the press, cutting, scraping, hooks brushes etc- Content: 1x Welding aid knife 1x Welding Fork Assistance 1x Welding assistance scraper 1x Hook assistant chip retention 1x Welding brush for assistance 1x Spatula Code H0096 Available Price €3.71
MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 The integrated mainboard driver MKS-GEN L V1.0 for 3D printer has been developed by Makerbase to optimize existing problems on the open source controller board such as Ramps 1.4.This product offers more flexible options for users.MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 features:- Mega2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.- Supports a variety of step-by-step drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change stepper motors and motors that users like.- Reserve the signal from the external controller, available to connect an external high current driver to drive stepper motors 57 and 86.se high quality MOSFET, better cooling and more stable. Code I0143 Available Regular price €26.36 -€2.00 Price €24.36
1m 6mm GT2 strap 3D printer 1m 6mm GT2 strap 3D printer features: - GT2 rubber strap with fiberglass reinforced - Length: 1m - Width: 6mm - Strap height: 1.38 mm Code I0006 Available Price €1.61
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €9.91
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Regular price €6.19 -15% Price €5.26
20x4 2004 LCD display PCF8574T I2C Backlit Blue - It consists of a 20-character, 4-row display - The display is compatible with the controller HD44780 and integrates the module so you can use it through the I2C protocol without any problem - Only two pins are needed for communication, SDA and SCL - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - It can be changed to any between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 20x4 2004 LCD display PCF8574T I2C Backlit Blue features: - LCD screen, 20 characters and 4 lines - 5V power supply - HD44780 compatible controller Code P0013 ✗ Out-of-Stock Regular price €7.02 -€1.50 Price €5.52
GP2Y0A21YK0F Strong Infrared IR Distance Meter Characteristic: - Supply voltage: 4.5V- 5.5V - Consumption: 30 mA typical - Analog output - Range: 10cm to 80cm - Dimensions: 29x12mm - Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino Code S0024 Available Price €8.22
Inlet Module Plug Fuse Switch 220V C14 3D Printer Inlet Module Plug Fuse Switch 220V C14 3D Printer features: - Voltage and current of 10A, 250V AC- Plug type - 3 pins IEC320 C14- Color of the red switch- Diameter holes 40 mm- Distance between holes 39mm- Size 47 x 27 mm- Total size of 58 x 50 x 34 mm Code K0022 Available Regular price €3.96 -€1.20 Price €2.76
12864 LCD Display Full Graphic Intelligent Controller 12864 LCD Display Full Graphic Intelligent Controller can be connected directly to your RAMPS 1.4. All new operations, such as calibration, axis movement can be done only with the smart rotary encoder. You don't need to use your PC. Just use the design in G-Code stored on the SD card. Code I0008 Last items in stock Price €10.32
Makerbase MKS TFT35 V1.0 touch screen smart display controller 3d printer Touch screen / intelligent controller MKS TFT35 for 3D RepRap printers. The MKS TFT35 is a 3.5 "color touch screen for various RepRap or open source 3D printers. The screen is compatible with MKS boards such as MKS Base, MKS Gen and MKS Mini. It is easy to connect and can be easily used with marlin.It is completely open software and allows any adjustment. To simplify an individual project, various projects can be selected in the standard internal software. In addition, 13 buttons can be freely assigned to activate various functions at the touch of a button. The firmware can be quickly and easily customized using a file on the SD card and can be changed without external programs.. Code I0184 ✗ Out-of-Stock Price €46.20
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 ✗ Out-of-Stock Price €8.18
MKS-GEN L V2.1 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 The integrated Mainboard MKS-GEN L V2.1 3D printer controller has been developed by Makerbase to optimise existing problems on the open source controller board such as Ramps 1.4. The MKS Gen L V2.1 is recommended as the main board for the OAT when using NEMA steppers. Code I0191 Available Price €26.36
Ramps 1.5 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers. RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0193 Available Price €4.95
MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 The integrated mainboard driver MKS-GEN L V1.0 for 3D printer has been developed by Makerbase to optimize existing problems on the open source controller board such as Ramps 1.4.This product offers more flexible options for users.MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 features:- Mega2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.- Supports a variety of step-by-step drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change stepper motors and motors that users like.- Reserve the signal from the external controller, available to connect an external high current driver to drive stepper motors 57 and 86.se high quality MOSFET, better cooling and more stable. Code I0143 Available Regular price €26.36 -€2.00 Price €24.36
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Available Price €4.09
12864 LCD Display Full Graphic Intelligent Controller 12864 LCD Display Full Graphic Intelligent Controller can be connected directly to your RAMPS 1.4. All new operations, such as calibration, axis movement can be done only with the smart rotary encoder. You don't need to use your PC. Just use the design in G-Code stored on the SD card. Code I0008 Last items in stock Price €10.32
Makerbase MKS TFT35 V1.0 touch screen smart display controller 3d printer Touch screen / intelligent controller MKS TFT35 for 3D RepRap printers. The MKS TFT35 is a 3.5 "color touch screen for various RepRap or open source 3D printers. The screen is compatible with MKS boards such as MKS Base, MKS Gen and MKS Mini. It is easy to connect and can be easily used with marlin.It is completely open software and allows any adjustment. To simplify an individual project, various projects can be selected in the standard internal software. In addition, 13 buttons can be freely assigned to activate various functions at the touch of a button. The firmware can be quickly and easily customized using a file on the SD card and can be changed without external programs.. Code I0184 ✗ Out-of-Stock Price €46.20
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 ✗ Out-of-Stock Price €8.18
MKS-GEN L V2.1 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 The integrated Mainboard MKS-GEN L V2.1 3D printer controller has been developed by Makerbase to optimise existing problems on the open source controller board such as Ramps 1.4. The MKS Gen L V2.1 is recommended as the main board for the OAT when using NEMA steppers. Code I0191 Available Price €26.36
Ramps 1.5 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers. RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0193 Available Price €4.95
MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 The integrated mainboard driver MKS-GEN L V1.0 for 3D printer has been developed by Makerbase to optimize existing problems on the open source controller board such as Ramps 1.4.This product offers more flexible options for users.MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 features:- Mega2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.- Supports a variety of step-by-step drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change stepper motors and motors that users like.- Reserve the signal from the external controller, available to connect an external high current driver to drive stepper motors 57 and 86.se high quality MOSFET, better cooling and more stable. Code I0143 Available Regular price €26.36 -€2.00 Price €24.36
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Available Price €4.09