Micro USB Interface Power Supply DC 7-12 VDC
  • Micro USB Interface Power Supply DC 7-12 VDC

Micro USB Interface Power Supply DC 7-12 VDC

A0078

This module is a 2-channel DC 7-12 VDC power supply for MB102 breadboards.
Each channel has its switch for configure the output voltage to 3.3V or 5V.
Its 3x2 male connectors allow it to be connected to the breadboard in a very simple way without soldering. Micro USB Interface Power Supply DC 7-12 VDC features:
- Operating voltage: DC 7-12 V
- Power display LED
- 1 Jack Female connector 2.1 mm to supply
- 1 AMS1117 3.3V regulator
- 1 AMS1117 5V regulator
- 4 3x2 connectors
- 1 5V micro USB female outlet
- Size: 5.5x3.5x1.5 cm

OEM
Add to wish list

Micro USB Interface Power Supply DC 7-12 VDC description

This module is a 2-channel DC 7-12 VDC power supply for MB102 breadboards.
Each channel has its switch for configure the output voltage to 3.3V or 5V.
Its 3x2 male connectors allow it to be connected to the breadboard in a very simple way without soldering.

Micro USB Interface Power Supply DC 7-12 VDC features:

- Operating voltage: DC 7-12 V
- Power display LED
- 1 Jack Female connector 2.1 mm to supply
- 1 AMS1117 3.3V regulator
- 1 AMS1117 5V regulator
- 4 3x2 connectors
- 1 5V micro USB female outlet
- Size: 5.5x3.5x1.5 cm

Customers who bought this product also bought

Electrical Contacts Cleaner Spray + Brush Kontakt S 400ml

A preparation to remove oxides and sulphites from electrical contacts and to provide protection against corrosion, ensures the flow of electricity especially in case of rusty or worn contacts.
It can be used in audio products - low frequency and high, electronic industry and in other places where clean contacts are required.
For cleaning contacts, electrical terminals, alternators, switches, plugs, sockets integrated circuits, lampholders, fuseholders, capacitor contacts, flowmeters etc. 400ml Electrical Contacts Cleaner Spray + Brush features:
- Restores low resistance in connections
- Used in audio technologies
- Protection against moisture and corrosion
- High quality - manufactured in EU

Q0028

Price €5.78

Screen OLED 0.96" 128x64 White SPI I2C 7 Pin

Screen OLED 0.96" 128x64 White SPI I2C 7 Pin features:
- Oled 0.96 "screen with 128 * 64 pixels
- Drive IC model SDD1306
- Power: 3V-5.5V - Viewing angle: 160 degrees
- SPI interface (I2C can be changed)
- Low consumption: 0.08W
- Operating temperature: -20 to 70 ºC
- PCB board dimension: 27 x 27mm
- Supports many control chip: 51 Series, MSP430 Series, STM32 / 2, CSR IC, etc.
- OLED technology offers high contrast, significantly improves black on screen energy efficiency - very low power consumption Applications: - Due to the size, quality and consumption of smart watch products, portable meters , medical devices, portable players, etc.

P0026

Regular price €4.13 -€1.50 Price €2.63

Water Flow Sensor 1-30l /Min YF-S201

The meter built on the basis of a water rotor and a Hall effect sensor
Please note this is not a Accuracy. Pulse rate varies slightly depending on flow rate, fluid pressure, and sensor orientation. Water Flow Sensor 1-30l /Min YF-S201 features:
- Working voltage range: DC 5 ~ 18 V
- Allow pressure: water pressure below 1.75Mpa
- Accuracy (flow-pulse output): ± 1 ~ 30 l / min
- Use temperature: ‰ ¤ 80 ° C
- Load capacity: ‰ ¤ 10 mA (5Vdc)
- Operating humidity: 35% ~ 90% RH (frost free)
- Temperature: -25 ~ + 80 ° C
- Outlet diameter: 1/2 "
- Red wire: positive supply
- Wire Black: negative power supply
- Yellow Cable: signal output
- Color: black
- Size: 6.2x3.6x3.4 cm

M0109

Price €4.92

Rechargeable Battery Samsung ICR18650 2600mAh Li-ion

Characteristic: - Lithium Battery WITHOUT Protection
- Nominal capacity: 2600mAh (discharge of 0.2C, 2.75V)
- Minimum capacity: 2550mAh (0.2C, 2.75V discharge)
- Charging voltage: 4.2 ± 0.05 V
- Nominal voltage: 3.63V
- Charging method: DC-CV (constant voltage with current limited)
- Charging current: standard charge: 1300mA, fast charge: 2600mA
- Charging time: standard charge: 3 hours, fast charge: 2.5 hours
- Max. Charging current: 2600mA (ambient temperature 25 °)
- Max. Discharge current: 5200mA (ambient temperature 25 °)
- Discharge cut-off voltage: 2.75V
- Cell weight: 47.0g maximum
- Cell dimension: Height: 65.00 mm max., Diameter: 18.40 mm max.

PP018

Price €4.95

Micro SD Card Reader/Recorder

The micro SD card reader module is a simple solution for transferring data to and from a standard micro SD card.
The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.
Ideal for projects with ARDUINO, PIC, AVR, STM32.
Micro SD Card Reader/Recorder features:
- Supply voltage: 4.5V- 5.5V
- Adjustable 3.3V built-in regulator for SPI pins
- Consumption <200mA
- Interface: SPI
- Dimensions: 24mmx 42mm x 12mm
Supports microSD cards (up to 2G) and micro SDHC (up to 32G)

M0006

Price €2.06
€7.85
Save €4.00 €3.85

3,85 tax excl.

1
16 items
Regular price €7.85 Price €3.85

Order until 4pm we will send today
30 days return