3x DC PCB Socket Connector 5.5 x 2.1

LED Diode Assortment Kit 50x Red Green Yellow Blue White features:
  
- Lens color: Red, green, yellow, blue - diffuse, light white
- Size: 5 mm
- Operating current: 20mA
- Voltage (red) 1.8V-2.3V
- Voltage (green) 3.2V-3.4V
- Voltage (yellow) 1.8V-2.3V
- Voltage (blue) 3.0V-3.2V
- Voltage (white) 3.2V - 3.4V
- Anode (A): Positive (long leg): 17mm
- Cathode (K): Negative (shorter leg): 15 mm
- Operating temperature: -25ºC / 80ºC
- Welding temperature: + 260ºC
- Quantity: - 50 units
                  - 10x red
                  - 10x green
                  - 10x yellow
                  - 10x blue
                  - 10x white

It is not possible to reverse the polarity by mistake.
JST PHR-2 Connector Male 2 PIN 2mm features:
Manufacturer JST Connector series: PH Connector: female connector Connector class: male Connector type: conduit-board Contactor raster: 2mm Number of pins: 2 Electrical mounting: THT Voltage Working: 100V Working current: 2A Working temperature: -25 ... 85 ° C Spatial orientation: vertical technical data sheet PH series

ABS Skin Color Filament 1.75mm 1kg for 3D Printer features:
- Premium Coil for 3D Printer

Small Probe Test for Multimeter Red Color features:
- 100% new and high quality
- Material: brass and plastic
- Powerful spring pulling the min hooks to grasp the small components firmly and avoid any short circuit
- Hands free to repair, you can connect the clips to multi-meter or DC POWER by a track
- It will help you to test IC or repair the cell phone and other mini electronic products more conveniently
- Length: 4.3 cm / 1.69 "
- Size of the brass hook: approximately 0.9mm x 0.4mm
- Red color

Heat Shrinkable Tube 5 Colors 3 Meters Package features:
- Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas.
- These heat shrink tubes are very flexible and of high quality. Made in EU
- Different sizes of 20 cm each are delivered:
* 1,6mm: black, brown, red, yellow, orange
* 2,4mm: black, brown , red, yellow, blue
* 3,2mm: black, brown, red, yellow, blue
- Quantity: 15 units
- Material: polyolefin
- Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter)
- Minimum shrinkage temperature: 115 ° C maximum 200 ° C

Long Life Replacement Tip Welder B11 Ø 3.8mm features:
- Power: 40W
- Rod ø 3.80mm
- Length 70 mm
- Long duration tip
- Quantity: 1 unit

Speed sensor module for Arduino motors features:
- Slot-type optocoupler sensor, slot width: 10 mm.
- The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it.
- Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high
- Power supply: 3.3-5V - Current consumption 15 mA max.
- PCB dimensions: 25 x 20 mm

This module includes the BMP280 component that converts atmospheric pressure, temperature and humidity with high precision into a digital signal.
The equipment uses the two I2C and SPI interfaces. The very good measurements made by the BMP280 allows the module to be used as an altimeter.
Its 5-pin straight connector allows easy connection to other electronic boards. BMP280 Temperature Barometric Pressure Sensor Module/SPI features:
- Interfaces:
       -I2C (up to 3.4 MHz)
       -SPI (up to 10 MHz)
- Supply voltage: 1.8-5VDC
- Module operating range:
       - Temperature: -40ºC to + 85ºC
0-100%
       - Pressure: 300-1100 hPa
- Resolution of the measures:
       - Temperature: 0.01ºC