Rocker Switch KCD11 250V/3A On/Off SPST

Ideal to power your Arduino board through the power input.
9v Battery Adapter Connector 6F22 with Cable features:

  - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields   Characteristic:   - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: micro USB female 

- 4 RGB LED panel with digital control to be connected in cascade to complete the reception and decoding of the data
- The light emitted is very powerful and can generate millions of colors thanks to the RGB device Panel Boards with 4-bit Precise Control 4 RGB LED 5050 CJMCU-2812-4 5V features:
- Operating voltage: 5 V
- LED color: RGB
- Number of LEDs: 4 (2 rows and 2 columns)
- Intelligent reverse polarity protection, the reverse polarity of power supply will not damage the IC
- IC control circuit
- Very powerful LED light
- 4 polarities:
      - VCC: positive power voltage
      - GND: ground connection
      - IN: input signal for cascade connection
      - OUT: output signal for cascade connection

The DIP switch type THT (4 rows 8 Pins) with a pitch of 2.54mm / 0.1 ". It works with the current of 50mA DC 12V.

Switch Button 8x8mm on-off features:
- Switch terminals: Weldable
- Measures: 8x8x13mm

SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base features:
Flux liquid alcohol-based for electronic welding.
Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductive
Form: liquid
Capacity: 50ml
Content of solid bodies: 0 ... 5%
Viscosity (at 25 ° C): 794Mg / cm3 The flux cleans and prepares the surfaces and components to be welded, it facilitates the adherence and fluidity of the tin thanks to the rest of the components.
It cleans easily with alcohol.
It can be used with any tin. Security: - Do not inhale the vapors of the bottle or those that come off when welding.
- Keep the boat tightly closed and far away from the children.
- Use in ventilated spaces.

12VDC plastic solenoid valve. Normally closed. Liquid can flow in one direction and a minimum pressure of 0.02Mpa (3 PSI) is required. This liquid valve would be a great addition to your robotic gardening project. There are two 1/2 ″ outlets. Normally, the valve is closed. When 12VDC is applied to the two terminals, the valve can be opened and pushed.

3.7V - 2A solar panel controller, charging, discharging lithium battery with lighting control with output from 2.5 V to 4.2 V. Integrate PWM suspension float.
Characteristic:
- Charging current: 2A
- Compatible battery type: Li-ion
- Type: 3.7V single cell lithium battery solar controller
- PWM suspension float with integrated maintenance charge. - Avoid overcharging the lithium battery.
- Battery type included: None
- Charging voltage output limit: 4.2V
- Low voltage drip charging of the battery: 2.5V
- Over discharge voltage: 2.8V
Order of use:
1 ) LED lights connected to "+ OUT", correspond to positive and negative.