XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.02
Multiplexer 16 Channels CD74HC4067 MUX/DEMUX A multiplexer of this type actually only acts as a switch 16 to a 1.The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features: - Based on chip CD74HC4067- Analog signal input: Y0-Y15, 16 channels- Analog signal output: Z pin- Digital input, channel control: S0-S3- Module size: approx. 4 x 1.8cm- Package includes:* 1 x CD74HC4067 MUX connection module* 2 x row of soldering pins Code C0006 Available Price €2.88
Passive Buzzer PCB Long Blue This module is a passive buzzer, a low trigger level alarm for Arduino. It emits different sounds at various frequencies. The buzzer sounds when the I / O port input is low level. Code M0163 Available Price €1.07
Unipolar Hall Effect Magnetic Sensor IC SH3144E Definition of the Hall effect: When a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicularly to the direction of current flow, a voltage, called the Hall voltage, proportional to the magnetic field, and the current appears on the side faces of the bar. This voltage is proportional to the speed of movement of the charge carriers, It is considerably higher in semiconductor materials than in metal conductors. Magnetic Sensor Characteristic: - Input Voltage: 3.8-30VDC - Output current: 40mA High output current capacity -40 mA maximum absolute Quad-Hall design virtually eliminates static mechanical effects Magnetic compensated temperature - Digital current sinking output Code S0049 Available Price €0.74
XM-15B Bluetooth Serial Port Module Master Slave Arduino compatible HC-05/06 XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features: * Power 3.0V -6V* 3.3V / 5V logic levels* Bluetooth version V2.1 + EDR* Frequency: 2.4GHz ISM band* Reach approx. 30m* Security: Authentication and encryption* Supports AT commands for configuration through a serial port* Working temperature: -20 ºC to +75 ºC* Working current - 50 mA* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)- Built-in hardware protector, never hangs Code W0022 Available Price €6.19
Heat Sink Aluminium Adhesive Radiator 25x25 Heatsink aluminium adhesive radiator for electronics components. Especially recomanded for passive cooling of Stepper Drive, MOSFET, VRM, Vram, IC Chips etc. Good thermal conductivity, reduce the risk of hardware failure due to overheating, made of high quality Aluminum. Code A0118 Available Price €0.98
Rocker Switch 3A 250V On/Off SPST Rocker Switch 3A 250V On/Off SPST features: - 2x AC 250V 3A 2 Pin ON/OFF I/O SPST Snap in mini oscillating switch- Rocker switch; Type: On/Off (SPST)- Control on and off SPST and 2 terminals- Voltage and Current: AC250V, 3A- Overall size: ~ 1.5 x 1 x 1.7 cm/0.6"x 0.4" x 0.7 "(L*W*H)- Mounting hole size: 1.35 x 0.8 cm/0.53"x 0.315" (L*W)- Black Code K0092 Available Price €0.78
Cable 1x0.35 Flexible single-pole 0.35mm red 3m Characteristic: -Low-voltage electric cables -Standard: EN 50525-2-31 -Number of conductors: 1x0.35mm2 -Service voltage: 300 / 500V -Service temperature: at 70ºC -Resistance at 20ºC: 55.0 Ohm / Km -Weight (Kg / Km): 7 -Outer diameter: 2.4mm Code K0033 Backorder Price €0.37
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94
DRV8833 Controller DC Motor PAP Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ). The motors are controlled, independently by means of PWM signals the direction of rotation of the motors can be controlled, neutral or stop with a frequency of up to 100 kHz. Two input signals (IN1 and IN2) can be used to control one motor (connected to OUT1 and OUT2) and the other two input signals (IN3 and IN4) to control the second motor (connected to OUT3 and OUT4). NOTE: This DRV8833 dual-bridge motor controller is the replacement for the TB6612FNG dual-channel motor controller. The pins come unsoldered. If the motor draws currents above 0.6A, the use of a heat sink may be required. DRV8833 Controller DC Motor PAP features: Code R0082 Available Price €2.02
L293D Motor Drive Shield Expansion Board It allows controlling many different types of engines: - Up to 4 bidirectional current motors- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos. L293D Motor Drive Shield Expansion Board features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A (650mA)- Logic voltage: 5V- Controller L293D- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.Pull-down resistors keep the motors off during startup. Code R0001 Available Price €2.44
A3967 DC Motor PAP Driver Stepper - Easy driver A3967 controller, double H-bridge controller driver. Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features: - Minimum operating voltage: 7.00 V - Voltage maximum operating: 30 V Code R0049 Available Price €2.44
L298N Motor Drive Controller Board Module Dual H Bridge DC It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles Code M0100 Available Price €2.31
Mini VNH3SP30 Stepper Motor Driver Module 30A Mini VNH3SP30 Stepper Motor Driver Modules capable of handling a high consumption motor. Code R0020 ✗ Out-of-Stock Price €4.01
L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It incorporates a switch for the connection and disconnection of the entire module. L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth /> Code M0183 Available Price €3.13
Controller TB6612FNG DC PAP motor TB6612FNG controller, double H-bridge controller driver. Allows to control up to 2 current motors continuous or bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. An improved version of the L298N. H-bridges are made up of MOSFET transistors, rather than BJT transistors as in the L298N. The TB6612FNG has better efficiency and smaller dimensions than the L298N. Controller TB6612FNG DC PAP motor features: - Minimum operating voltage: 4.5 V - Maximum operating voltage: 13.5 V (15V max) - Maximum current: ± 3A per channel (1.2 A direct current per channel) - Logic voltage: 5V Code R0002 Available Price €4.95
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €6.57
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €19.83
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94
DRV8833 Controller DC Motor PAP Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ). The motors are controlled, independently by means of PWM signals the direction of rotation of the motors can be controlled, neutral or stop with a frequency of up to 100 kHz. Two input signals (IN1 and IN2) can be used to control one motor (connected to OUT1 and OUT2) and the other two input signals (IN3 and IN4) to control the second motor (connected to OUT3 and OUT4). NOTE: This DRV8833 dual-bridge motor controller is the replacement for the TB6612FNG dual-channel motor controller. The pins come unsoldered. If the motor draws currents above 0.6A, the use of a heat sink may be required. DRV8833 Controller DC Motor PAP features: Code R0082 Available Price €2.02
L293D Motor Drive Shield Expansion Board It allows controlling many different types of engines: - Up to 4 bidirectional current motors- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos. L293D Motor Drive Shield Expansion Board features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A (650mA)- Logic voltage: 5V- Controller L293D- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.Pull-down resistors keep the motors off during startup. Code R0001 Available Price €2.44
A3967 DC Motor PAP Driver Stepper - Easy driver A3967 controller, double H-bridge controller driver. Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features: - Minimum operating voltage: 7.00 V - Voltage maximum operating: 30 V Code R0049 Available Price €2.44
L298N Motor Drive Controller Board Module Dual H Bridge DC It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles Code M0100 Available Price €2.31
Mini VNH3SP30 Stepper Motor Driver Module 30A Mini VNH3SP30 Stepper Motor Driver Modules capable of handling a high consumption motor. Code R0020 ✗ Out-of-Stock Price €4.01
L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It incorporates a switch for the connection and disconnection of the entire module. L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth /> Code M0183 Available Price €3.13
Controller TB6612FNG DC PAP motor TB6612FNG controller, double H-bridge controller driver. Allows to control up to 2 current motors continuous or bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. An improved version of the L298N. H-bridges are made up of MOSFET transistors, rather than BJT transistors as in the L298N. The TB6612FNG has better efficiency and smaller dimensions than the L298N. Controller TB6612FNG DC PAP motor features: - Minimum operating voltage: 4.5 V - Maximum operating voltage: 13.5 V (15V max) - Maximum current: ± 3A per channel (1.2 A direct current per channel) - Logic voltage: 5V Code R0002 Available Price €4.95
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €6.57
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €19.83