Micro Motor 3V 5V 6V DC DIY for Arduino UNO Mega Robotics For Arduino, Smart Car, Robotics.Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC DIY Arduino UNO Mega Robotics features: - Operating voltage: 1.5V to 6V- DC current: 350mA- Torque max.: 15g / cm- Max speed: 12000rpm- Weight: 16.5 g Code R0037 Available Price €0.98
Controller TB6612FNG DC PAP motor TB6612FNG controller, double H-bridge controller driver. Allows to control up to 2 current motors continuous or bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. An improved version of the L298N. H-bridges are made up of MOSFET transistors, rather than BJT transistors as in the L298N. The TB6612FNG has better efficiency and smaller dimensions than the L298N. Controller TB6612FNG DC PAP motor features: - Minimum operating voltage: 4.5 V - Maximum operating voltage: 13.5 V (15V max) - Maximum current: ± 3A per channel (1.2 A direct current per channel) - Logic voltage: 5V Code R0002 Available Price €5.99
L293D Motor Drive Shield Expansion Board It allows controlling many different types of engines: - Up to 4 bidirectional current motors- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos. L293D Motor Drive Shield Expansion Board features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A (650mA)- Logic voltage: 5V- Controller L293D- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.Pull-down resistors keep the motors off during startup. Code R0001 Available Price €2.95
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 ✗ Out-of-Stock Price €2.95
Servo Arm 25T Aluminium for Futaba MG996 MG995 Hitec JR Servo Arm 25T Aluminium for Futaba MG996 MG995 Hitec JR features: - 25T Servo Arm for Futaba, Tower Pro and High Power Servos - Material: Aluminum - Color: red - Size: 35.5 x 15 x 6mm - Weight: 4 grams - M3 thread for joints of cars or helicopters. - Hole distance 20 and 24 mm from the servo outlet. - Quantity: 1 unit Code R0040 Available Price €1.59
Mosfet 24V 5A IRF520 PWM controller Mosfet 24V 5A IRF520 PWM controller features: - The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater. - The built-in IRF520 N-MOSFET transistor - Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI) - Charging voltage: 0-24V - Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point) - 60W max power (more than 10W must be equipped with a heat sink) - Terminalblock connectors - LED indicating the presence of power - Dimensions: 33x24mm Code A0022 Available Regular price €2.49 -€0.50 Price €1.99
Micro Servo 9g SG90 Tower Pro Micro Servo 9g SG90 features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0013 Available Regular price €2.69 -€0.20 Price €2.49
Mini VNH3SP30 Stepper Motor Driver Module 30A Mini VNH3SP30 Stepper Motor Driver Modules capable of handling a high consumption motor. Code R0020 ✗ Out-of-Stock Price €4.85
M3 Hexagonal Spacer 25mm Male - Female Brass Characteristic: -Metric thread M3 -Male-Female separator 25mm -Quantity: 5 units Code H0048 Available Price €0.45
DC Gear Motor 6V 1:48 for Arduino DC Gear Motor 6V 148 Arduino features:- Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Reduction: 1:48 Code R0008 Available Regular price €1.90 -€0.41 Price €1.49
L298N Motor Drive Controller Board Module Dual H Bridge DC It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles Code M0100 Available Price €2.79
VNH3SP30 Stepper Motor Driver Module 30A Driver capable of handling up to two high consumption motors.We can weld 5mm screw terminals (not included), making it easy to connect other gauge cables. Code R0010 Last items in stock Regular price €15.58 -€2.50 Price €13.08
DC Gear Motor N20 200 RPM 12V DIY Robot DC Gear Motor N20 200 RPM 12V DIY Robot features: - Voltage: 12V- Speed of rotation: 200RPM- Motor dimensions:* Diameter 12 mm* Height 24 mm- For Arduino, Smart Car, Robotics, Fans, Appliances Code R0035 Available Regular price €5.90 -€1.00 Price €4.90
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.95 -€0.50 Price €2.45
Continous Rotation 360 Degree Servo S3003 Continous Rotation 360 Degree Servo S3003 features: - Operating voltage: 4.8 V to 6 V- Torque max.: 4.1kg / cm (6V)- Operating speed: 0.23sec / 60degree (4.8V), 0.19sec / 60degree (6V)- Radio max.: 360º- Temperature range: -20º + 60ºC degrees- Weight: 38 g- Cable length: 26cm- Dimensions: 40.5 x39x 20 mm- Servo connector: JR- Chinese manufacture Code R0019 Available Regular price €7.95 -€0.96 Price €6.99
Micro Servo Compatible with MG90S Micro Servo Compatible with MG90S features: - Operating voltage: 4.8Vdc (5V) or 6Vdc - Torque: 1.80 kg / cm at 4.8V and 2.20kg / cm at 6V - Speed: 0.1seconds / 60º at 4.8V and 0.8 seconds / 60º at 6V - Gear type: metallic - Turning width: 180º - Temperature working: from -30 to 60 ºC - 3 plastic propellers / arms - Fixing screws - Size: 22.6 x 11.8 x 31 mm - Weight: 13.4 gr Code R0015 Available Price €3.99
LSC-16 Digital Servo Motor Controller 16 channels LSC-16 Digital Servo Motor Controller 16 channels features: - With current limiting protection. The servo output is isolated from the CPU to prevent increased servo current causing damage to the CPU. - CPU using high performance STM32 single chip microcomputer with ARM Cortex-M3 corer, control High precision 16-channel servo movement, adjustable speed. - 16M high capacity memory, enough for your use! It can contain 230 action groups! Each action group can hold up to 510 actions! - Supports online debugging, no need to install any driver by yourself (Install Drivers Automatically). - 0 ~ 3rd and 12th - 15th servo interface have over current protection! Greatly reducing the risk of burned servo due to locked rotor. Code R0046 Available Regular price €25.80 -€2.00 Price €23.80
Car Robot Tire Wheel Smart Car Car Robot Tire Wheel Smart Car features:- Dimensions of the wheel: - Diameter: 65mm - Width: 26 mm- Quantity: 1 unit Code R0009 Available Regular price €1.90 -€0.41 Price €1.49
PCA9685 digital servo motor controller 16 channel PWM This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos. It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity. PCA9685 digital servo motor controller 16 channel PWM features: - Supply voltage: 3-5 VDC, - Maximum motor voltage: 6 VDC, - Number of channels: 16, - Resolution per channel: 12 bits, - Interface: I2C, - Working frequencies: 40-1000 Hz, - PCB size: 62.3x25.3mm . Code R0074 Available Price €5.10
L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It incorporates a switch for the connection and disconnection of the entire module. L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth /> Code M0183 Available Price €3.79
A3967 DC Motor PAP Driver Stepper - Easy driver A3967 controller, double H-bridge controller driver. Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features: - Minimum operating voltage: 7.00 V - Voltage maximum operating: 30 V Code R0049 Available Price €2.95
DC Gear Motor and Tire Wheel for Smart Car Robot DC Gear Motor and Tire Wheel for Smart Car Robot features:- Voltage: 3 to 6 Vdc- Reduction: 1:48- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0011 Available Price €3.89
DRV8833 Controller DC Motor PAP Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ). The motors are controlled, independently by means of PWM signals the direction of rotation of the motors can be controlled, neutral or stop with a frequency of up to 100 kHz. Two input signals (IN1 and IN2) can be used to control one motor (connected to OUT1 and OUT2) and the other two input signals (IN3 and IN4) to control the second motor (connected to OUT3 and OUT4). NOTE: This DRV8833 dual-bridge motor controller is the replacement for the TB6612FNG dual-channel motor controller. The pins come unsoldered. If the motor draws currents above 0.6A, the use of a heat sink may be required. DRV8833 Controller DC Motor PAP features: Code R0082 ✗ Out-of-Stock Price €2.45
Motor Support for Arduino Smart Car the robot car motor holder and assembly accessories Code R0050 Available Price €0.95
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €23.99
Servo with Rotation 180 Servo Motor Type S3003 Servo with Rotation 180 Servo Motor Type S3003 features: - Model Aircraft Futaba Arduino Robotics - Operating Voltage: 4.8V to 6V - Max Torque: 4.1kg / cm (6V) - Operating speed: 0.23sec / 60 degrees (4.8V), 0.19sec / 60 degrees (6V) - Max radius: 180º - Temperature range: -20 + 60 C degrees - Weight: 38 g - Cable length: 26cm - Dimensions: 40.5 x39x 20 mm - Servo connector: JR - Chinese manufacturing Code R0018 Available Regular price €6.29 -€0.30 Price €5.99
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €7.95
Servo Driver for micro:bit, 16-Channel, 12-bit The micro:bit servo driver module, 16 channel, 12 bit, I2C interface. Have you ever had the problem of not having enough micro:bit PWM outputs when trying to create a robotic arm or other robot that requires multiple servos? At times like this a great solution comes to your aid. This servo controller will be the perfect choice. Code WV007 Available Price €21.95
Servo Motor Type S3003 Aeromodelling Servo Motor Type S3003 Aeromodelling features: - Operating voltage: 4.8 V to 6 V - Max torque: 4.1kg / cm (6V) - Operating speed: 0.23sec / 60 degree (4.8V), 0.19sec / 60 degree (6V) - Max radius: 180 ° (90º in each direction) - Temperature range: - 20 + 60 C degrees - Weight: 38 g - Cable length: 26cm - Dimensions: 40.5 x39x 20 mm - Servo connector: JR - Chinese Manufacture Code R0017 Available Price €6.29
MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V High power digital servo, better precision than the MG995. MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V features: - Operating voltage: 4.8 V to 7.2 V- Consumption: 100mA- Torque max.: 12kg / cm (6V)- Operating speed: 0.22sec / 60degree (4.8V), 0.19sec/60degree (6V)- Max. Radio: 180ºC- Temperature range: 0-55 degrees- Weight: 55 g- Cable length: 29cm- Dimensions: 54 x38x 20 mm- Servo connector: JR (JR and Futaba adaptable) Code R0016 Available Regular price €8.95 -€1.00 Price €7.95
Platform camera + 2 SG90 Servo Motor 9g - Kit for Arduino Platform camera + 2 SG90 Servo Motor 9g Arduino Kit features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Force: 1.2kg / 42.3oz (4.8V), 1.6kg / 56.4oz (6.0V)- Working temperature: -30 to +60 Degree C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Contents: - Servo 9g - 2 units- Platform for camera - 1 unit Code R0021 Available Price €4.99
5x Hexagonal Separator M3 10mm Male-Female Brass 5x Hexagonal Separator M3 10mm Male-Female Brass features: -Metric thread M3-Male-Female Separator 10mm-Quantity: 5 units Code H0047 Available Price €0.39
Geared Motor with Encoder (6V 1:48 L Shape) Geared Motor with Encoder (6V 148 L Shape) features: - Voltage: 3 to 6V DC- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Reduction: 1:48 Code R0070 Available Price €3.29
Geared Motor with Encoder 6V 1:120 for Arduino Smart Car Robot Geared Motor with Encoder 6V 1120 Arduino Smart Car Robot features:- Voltage: 3 to 6Vdc- Speed without load: 200 RPM to 6Vdc- No-load current: 110mA at 3Vdc - 250mA at 6Vdc- Reductive: 1: 120 Code R0043 Available Price €3.45
Wheels 30mm PP 360° Rotation for Cylindrical Use White plastic wheel with silver tone metal support.It allows a 360° rotation, provides a good resistance to rolling, wheel silently and without problems. Wheels 30mm PP 360° Rotation for Cylindrical Use features: - Main material: Polypropylene (PP), steel- Main color: White, silver tone- Total size: Total height: 45mm / 1.8 "- Wheel size: 30 x 13mm / 1.2 "x 0.5" (P * A)- Hole diameter for mounting: 4mm / 0.16 "- Space between holes: 28 x 22mm / 1.1 "x 0.9" (L * P)- Size of the top plate: 38 x 32mm / 1.5 "x 1.3" (L * P) Code H0128 Available Price €1.69
Motor 28BYJ-48 5V Stepper The 28BYJ-48 has everything you need to start using stepper motors in your project. A stepper motor converts digital impulses into small movement steps. in one direction Characteristic: - Motor model: 28BYJ-48 - Motor phases: 4 - Operating voltage: 5V - Frequency: 100 Hz - Operating current: 200mA - Max Power: 20W - Winding resistance: 70 ohm - Angle per step: 5,625º - Steps per lap: 64 - Torque: 0.3 Kgr / cm - Speed: 1900 rpm - Operating temperature: -45ºC to + 125ºC - Motor cable length: 19cm - Motor block diameter: 28mm - Motor dimensions: 42mm x 32mm x 30mm Code R0044 Available Price €2.29
Gear Reducer Motor 6V DC 200RPM for Smart Car Gear Reducer Motor 6V DC 200RPM for Smart Car features: - Voltage: 3 to 6V DC- Speed without load: 200 RPM to 6V DC Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles - Wiring of the 6V DC 200 RPM motor with the L298N double bridge H controller module Code R0045 Available Price €2.39
Free metal wheel 360° with plastic support for robotics Free metal wheel with white plastic support.It allows a 360 ° rotation, wheel silently and without problems. Free metal wheel 360° with plastic support for robotics features: - Main material: Polypropylene (PP), Steel.- Main color: White, silver tone. - Dimensions of support: 50x24mm. - Ball diameter: 15.80mm. Code H0149 Available Price €1.39
Tower Pro Micro Servo 9g SG90 360 degree Tower Pro Micro Servo 9g SG90 360 degree features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0075 Available Price €2.95
25T metal disc for MG996R servomotors + 4 screws Metal disc diameter 25mm with 4 mounting holes for 25T RC MG996R servos 25T metal disc for MG996R servomotors + 4 screws features: - Material: Aluminum - Gear teeth: 25T - 4x M3 mounting holes rotated - Diameter disc: 25mm - Includes: 4 fixing screws. Code R0076 Available Price €0.90
Servo 9g SG92r 2.5kg 9g digital servo new version of SG90. POM with Carbon fiber gears set and control arms are more durable use than SG90 nylon gear and more torque. It is a good choice for park size 3D models , high speed jets and R/C airplane 250 450 RC helicopter Servo 9g SG92r 2.5kg features: Weight: 9g Operating voltage: 4.8v Stall torque: 2.5kg /cm(4.8v) Gear type: POM with carbon fiber Operating speed: 0.1sec /60degree (4.8v) Temperature range: 0„ƒ_ 55„ƒ Dead band width:1us servo wire length: 25 cm Servo Plug: JR (Fits JR and Futaba) servo arms &screws included and fit with Futaba servo arm Code R0079 Available Price €4.30
Micro Motor 3V 5V 6V DC with cable conector male For Arduino, Smart Car, Robotics.Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC with cable conector male features: - Operating voltage: 1.5V to 6V - Cable 16cm with male connector - DC current: 350mA - Torque max.: 15g / cm- Max speed: 12000rpm- Weight: 16.5 g Code R0080 Available Regular price €1.95 -€0.26 Price €1.69
5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat The 28BYJ-48 has everything you need to start using stepper motors in your projectA stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller cardCan control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mAEquipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features: - Engine model: 28BYJ-48- Phases engine: 4- Operating voltage: 5V- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 ohm- Angle per step: 5,625º- Steps per round: 64- Torque: 0.3 Kgr / cm- Speed: 1900 rpm Code R0038 Available Price €2.95
Motor Nema 17 1.22kg 17HS2408 Characteristic: - Motor passes 1.8º (200 steps per turn) - Capable of loading 1.22 kg / cm Code I0065 Last items in stock Price €8.99
Motor Nema 17 4.28kg 17HS4401 It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 4.28 kg/cm. It comes with a 1m cable. We have the best stepper motors at the best prices! Code I0020 Available Regular price €11.50 -€1.55 Price €9.95
Heat Sink Aluminium Nema 17 Heat Sink Aluminium Nema 17 features: - MK8 Extruder Radiator Heatsink Printer - Ideal for NEMA17 motors and MK7 and MK8 extruders - Dimensions 40 x 40x 11mm Code I0038 Available Price €1.79
Mounting Bracket for Nema Motor 23 57mm/76mm 67mm L shape alloy steel mounting bracket for NEMA23 3D stepper motor printer Mounting Bracket for Nema Motor 23 57mm/76mm features: - Compatible with Nema 23 body length: 57mm and 76mm - Material: alloy steel - Size: 67 x 67 x 2,7 mm - Black color - Fit for stepper motor as NEMA23 Code I0116 Available Price €3.90
Mounting Bracket for Nema Engine 17 42mm Mounting Bracket for Nema Engine 17 42mm features: - Steel bracket for PAP Nema 17 3D printer motor - Mounting bracket of 42mm L shape alloy steel for The NEMA17 3D Stepper Motor Printer - Material: Alloy Steel - Size: 5 x 5 x 5cm - Black Color - Fit for 42mm Stepper Motor as NEMA17 Code I0044 Available Price €3.75
Motor Nema 17 42HS482504 2.5A One of the most popular stepper motors with 200 steps per revolution and a maximum load of 5 kg/cm. It comes with a 30 cm cable. We have the best stepper motors at the best prices! Code I0126 Available Price €14.90
Motor Nema 23 28.5kg JK57HS112-4204 It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 28.5 kg/cm. Comes with a 50 cm cable. We have the best stepper motors at the best prices! Perfect for CNC machines! Code I0168 Available Regular price €67.90 -€5.00 Price €62.90
Dupont female-female connector cable to PH2.00 for Nema motor Dupont female-female connector cable to PH2.00 for Nema engine features: Dupont 2.54 female to PH2.00 female connecting cable for Nema motor Length 100cm Code I0177 Available Price €1.95
Green Propeller + Micro Motor 3V 5 6V DC DIY for Arduino Small 3V-6V DC motor ideal for DIY projects Code R0032 Available Price €1.77
Blue Propeller + Micro Motor 3V 5 6V DC DIY for Arduino Small 3V-6V DC motor ideal for DIY projects Code R0031 Available Price €1.77
Red Propeller + Micro Motor 3V 5 6V DC DIY for Arduino Small 3V-6V DC motor ideal for DIY projects Code R0033 Available Price €1.77
Gear Reducer Motor 5V DC 1:48 Robot Support for Arduino Smart Car Gear Reducer Motor 5V DC 148 Robot Support Arduino Smart Car features: - Voltage: 3 to 6Vdc - Speed without load: 100 RPM to 6Vdc - No-load current: 90mA to 3Vdc - 180mA to 6Vdc - Reduction: 1:48 - Content: * 1 unit - direct current motor * 1 unit - support with screws Code R0041 Available Regular price €2.85 -5% Price €2.71
MG995 and MG996 Servo Motor U-Mounting Bracket Kit Black Black U-shaped servo motor mounting bracket for MG995 and MG996 servo motors. Ideal for robot arms or creating your own structures. Includes hardware. Code R0088 Available Price €3.99
Slip ring mini 12mm diameter 12 wires A sliding ring capable of holding up to 12 wires of 12mm diameter. Code R0092 Backorder Price €33.95
Slip ring 22mm diameter 6 wires A slip ring capable of holding up to 6 wires of 22mm diameter. Code R0093 Last items in stock Price €29.50
Wheel for continuous rotation servo SG90 Servo FS90R Wheels for 360 degree continuous rotation servo motors type SG90, FS90R, SG92r. The wheels have silicone tyres and measure 60 mm (2.36″) in diameter. Four additional mounting holes for 4-40 bolts allow the wheel to be used with several of our universal mounting bracket. Code R0091 Available Price €1.90