Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Available Price €4.95
Construction kit 32 IN 1 micro:bit - Wonder Building kit With this 32 in 1 construction kit you can build all 32 options or develop your imagination by building your own project. Note: the micro:bit board is not included, you can buy it separately. Code EL0112 ✗ Out-of-Stock Regular price €94.95 -€5.00 Price €89.95
Rotary Encoder EC11 with Push Button Switch It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0. Code M0012 Available Price €1.39
TM1637 4-Digit Digital Display Module Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. The display module 4-digit LED with TM1637. The unit can be controlled with just two DIO and CLK control lines. TM1637 4-Digit Digital Display Module features: - 3V-5V supply voltage - Current consumption 250 mA - 7-segment display 4 digits common anode - Digit size: 0.36 inches - Dimensions: 42x24x11mm Code M0104 Available Price €2.15
Rain Sensor Module Water Droplet Detector The module has two outputs: analog A0 and digital D0. digital output D0 - signal 0 or 1 appears depending on the configuration of threshold. The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - digital switching output indicator - Measurements PCB: 3 x 1.5 cm - Sensor measurements: 5.4 x 3.9 cm Code S0022 Available Price €1.69
Water Level Sensor Module One Mega Pic Easily convert water level to analog signal The analog output signal can be read directly on the Arduino board Characteristic: - Operating voltage: 3.3V -5 V - Consumption: less than 20 mA - Sensor type: Analog - Operating temperature: 10º C -30º C - Detection area: 40 mm x 16 mm - Dimensions: 60 mm x 20 mm Code S0023 Available Price €1.39
10m Rigid cable, 22AWG black PVC wire, 0.35mm2 Characteristic: -Conductor: solid wire, tinned copper -Insulation: PVC -Low voltage electrical cables - Nominal voltage 300V / 80C -Standard: UL 1007 -Number of conductors: 22AWG, 1x0.35mm2 -Outer diameter: 1.6mm Code K0224 Backorder Price €3.89
Ceramic Capacitor 100nF 50v 104 Ceramic Capacitor 100nF (0,1uF) 50v 104 PCB PIC Arduino features: Orders only in multiples of 20 units-Type: Ceramic Y5V-Tolerance: +80/-20%-Dimensions: diameter 9.5mm, pitch 5.08mm Code D0057 Available Price €0.06
Wheels 30mm PP 360° Rotation for Cylindrical Use White plastic wheel with silver tone metal support.It allows a 360° rotation, provides a good resistance to rolling, wheel silently and without problems. Wheels 30mm PP 360° Rotation for Cylindrical Use features: - Main material: Polypropylene (PP), steel- Main color: White, silver tone- Total size: Total height: 45mm / 1.8 "- Wheel size: 30 x 13mm / 1.2 "x 0.5" (P * A)- Hole diameter for mounting: 4mm / 0.16 "- Space between holes: 28 x 22mm / 1.1 "x 0.9" (L * P)- Size of the top plate: 38 x 32mm / 1.5 "x 1.3" (L * P) Code H0128 Available Price €1.69
Green Propeller + Micro Motor 3V 5 6V DC DIY for Arduino Small 3V-6V DC motor ideal for DIY projects Code R0032 Available Price €1.77
DC Gear Motor 6V 1:48 for Arduino DC Gear Motor 6V 148 Arduino features:- Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Reduction: 1:48 Code R0008 Available Regular price €1.90 -€0.41 Price €1.49
Motor Nema 17 42HS482504 2.5A One of the most popular stepper motors with 200 steps per revolution and a maximum load of 5 kg/cm. It comes with a 30 cm cable. We have the best stepper motors at the best prices! Code I0126 Available Price €14.90
Slip ring mini 12mm diameter 12 wires A sliding ring capable of holding up to 12 wires of 12mm diameter. Code R0092 Backorder Price €33.95
Tower Pro Micro Servo 9g SG90 360 degree Tower Pro Micro Servo 9g SG90 360 degree features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0075 Available Price €2.95
Motor Nema17 JK42HS34-0404 It is one of the most popular stepper motors with 200 steps per revolution and a maximum load of 2.6 kg/cm (0.25 Nm). It is supplied with a voltage of 12.0 V, consumes a current of 400 mA per coil. Dimensions: 42 x 42 x 34 mm (NEMA 17). Comes with a 30 cm cable. We have the best stepper motors at the best prices! Code I1105 Available Price €14.90
Slip ring 22mm diameter 6 wires A slip ring capable of holding up to 6 wires of 22mm diameter. Code R0093 Last items in stock Price €29.50
Servo Motor Type S3003 Aeromodelling Servo Motor Type S3003 Aeromodelling features: - Operating voltage: 4.8 V to 6 V - Max torque: 4.1kg / cm (6V) - Operating speed: 0.23sec / 60 degree (4.8V), 0.19sec / 60 degree (6V) - Max radius: 180 ° (90º in each direction) - Temperature range: - 20 + 60 C degrees - Weight: 38 g - Cable length: 26cm - Dimensions: 40.5 x39x 20 mm - Servo connector: JR - Chinese Manufacture Code R0017 Available Price €6.29
Micro Motor 3V 5V 6V DC with cable conector male For Arduino, Smart Car, Robotics.Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC with cable conector male features: - Operating voltage: 1.5V to 6V - Cable 16cm with male connector - DC current: 350mA - Torque max.: 15g / cm- Max speed: 12000rpm- Weight: 16.5 g Code R0080 Available Regular price €1.95 -€0.26 Price €1.69
Slip ring 22mm diameter 6 wires A slip ring capable of holding up to 6 wires of 22mm diameter. Code R0093 Last items in stock Price €29.50
Red Propeller + Micro Motor 3V 5 6V DC DIY for Arduino Small 3V-6V DC motor ideal for DIY projects Code R0033 Available Price €1.77
Motor Nema 17 1.22kg 17HS2408 Characteristic: - Motor passes 1.8º (200 steps per turn) - Capable of loading 1.22 kg / cm Code I0065 Available Price €8.99
MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V High power digital servo, better precision than the MG995. MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V features: - Operating voltage: 4.8 V to 7.2 V- Consumption: 100mA- Torque max.: 12kg / cm (6V)- Operating speed: 0.22sec / 60degree (4.8V), 0.19sec/60degree (6V)- Max. Radio: 180ºC- Temperature range: 0-55 degrees- Weight: 55 g- Cable length: 29cm- Dimensions: 54 x38x 20 mm- Servo connector: JR (JR and Futaba adaptable) Code R0016 Available Regular price €8.95 -€1.00 Price €7.95
Motor Nema17 JK42HS34-0404 It is one of the most popular stepper motors with 200 steps per revolution and a maximum load of 2.6 kg/cm (0.25 Nm). It is supplied with a voltage of 12.0 V, consumes a current of 400 mA per coil. Dimensions: 42 x 42 x 34 mm (NEMA 17). Comes with a 30 cm cable. We have the best stepper motors at the best prices! Code I1105 Available Price €14.90
DC Gear Motor 6V 1:48 for Arduino DC Gear Motor 6V 148 Arduino features:- Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Reduction: 1:48 Code R0008 Available Regular price €1.90 -€0.41 Price €1.49
DC Gear Motor and Tire Wheel for Smart Car Robot DC Gear Motor and Tire Wheel for Smart Car Robot features:- Voltage: 3 to 6 Vdc- Reduction: 1:48- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0011 Available Price €3.89
Blue Propeller + Micro Motor 3V 5 6V DC DIY for Arduino Small 3V-6V DC motor ideal for DIY projects Code R0031 Available Price €1.77
Dupont female-female connector cable to PH2.00 for Nema motor Dupont female-female connector cable to PH2.00 for Nema engine features: Dupont 2.54 female to PH2.00 female connecting cable for Nema motor Length 100cm Code I0177 Available Price €1.95
Heat Sink Aluminium Nema 17 Heat Sink Aluminium Nema 17 features: - MK8 Extruder Radiator Heatsink Printer - Ideal for NEMA17 motors and MK7 and MK8 extruders - Dimensions 40 x 40x 11mm Code I0038 Available Price €1.79