Servo Motor Type S3003 Aeromodelling

LM35 Temperature Sensor LM35DZ TO92 features:
- The output is linear and each degree Celsius equals 10 mV
- Power supply from 4 to 30 Vdc
- Connection through analog input
- Temperature range from 0ºC to 100ºC
- Linearity +10 mV / ºC
- Quantity: 1 unit

Speed sensor module for Arduino motors features:
- Slot-type optocoupler sensor, slot width: 10 mm.
- The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it.
- Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high
- Power supply: 3.3-5V - Current consumption 15 mA max.
- PCB dimensions: 25 x 20 mm

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

M18 Inductive Proximity Sensor features:
- Inductive proximity sensor detection switch LJ18A3-8-Z / BX
- NPN DC6-36V
- A Often used for 3D printer bed leveling
- Cylindrical cable type DC 3 cable type (black, brown, blue)
- Inductive sensor type
- NPN NO (Normal Open )
- Detecting distance 8mm
- DC supply voltage 6-36V
- Current output 300mA
- Response frequency 0.5KHz
- Detects iron / aluminum - Operating temperature -25 ° C to + 70 ° C (Non-freezing condition)
- Head diameter 18 mm
- Size 6.9 x 2cm
- Cable length 90cm

- The PCF8574P is an 8-bit remote I / O expander for the I2C bus with 16-pin DIP packet interrupt. - Provides general-purpose remote I / O expansion via a two-wire, two-way I2C bus (Serial Clock (SCL), Serial Data (SDA)).
- Devices consist of eight quasi-directional ports , 100KHz I2C bus interface, three hardware address inputs and interrupt output operating between 2.5V and 6V.
- Quasi-bidirectional port can be independently assigned as one input to monitor interrupt status or keyboards or as an output to activate indicating devices like LEDs. - System Master can read from the input port or write to the output port through a single register.

DC Gear Motor and Tire Wheel for Smart Car Robot features:
- Voltage: 3 to 6 Vdc
- Reduction: 1:48
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Dimensions of the wheel: diameter 65mm - width 26 mm

Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features:
- Power supply: 3.3 - 5V DC
- OUT level 0/1 output
- Sensitivity adjustment
- Power LED
- Distance from detection: 2 - 30cm (max60cm)
- detection angle: 35º
- LED output status indicator
- Dimensions: 40x13x8mm

Characteristic: -Length: 20cm
-Quantity: 40 cables
-Mono Dupont connectors on both ends
-Compatible with 2.54mm female connectors
-High quality and good working condition
-Easy to install and use