Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 Last items in stock Price €25.90
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €10.90
DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino - The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree Characteristic: - Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Write texts on the OLED 0.96 '' screen - Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen Send /> Code M0099 Available Regular price €6.49 -€2.00 Price €4.49
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.99
M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features: - This sensor can be configured as auto Z axis level - Sensor detection switch inductive proximity LJ12A3-4-Z / BY - PNP DC6-36V - Often used for 3D printer bed leveling - Typical application: printer bed level sensor 3D - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - PNP NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C at + 55 ° C (Non-freezing condition) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0036 Available Regular price €3.99 -€0.50 Price €3.49
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 ✗ Out-of-Stock Price €4.99
Ethernet Shield W5100 Web Server Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip. Provides an easy way to connect your module to the local network now internet. Compatible with the official Arduino Ethernet library. With this shield you can build a web server. It can be used as a server or as a client. It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features: - Controller: Wiznet W5100 - Supports protocols TCP and UDP - Supports up to 4 simultaneous connections - Compatible with all Arduino versions: UNO, mega 1280/2560 - Dimensions: 74 x 54 x 25mm Code W0007 Available Price €21.95
Sensor Module Infrared Obstacle Detector Car Robot Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features: - Power supply: 3.3 - 5V DC - OUT level 0/1 output - Sensitivity adjustment - Power LED - Distance from detection: 2 - 30cm (max60cm) - detection angle: 35º - LED output status indicator - Dimensions: 40x13x8mm Code S0011 Available Price €1.49
2km radius SI4463 433MHz RF Telemetry Arduino compatible A compact, low-power Bottom Effect System Transceiver. Transceiver based on the SI4463 Silicon Labs chip. Industry standard model. In full power operating conditions, open the communication distance up to 2000 km. Much more than the SI4432. Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver. Higher sensitivity -126dBm. The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation. The data rate in the range of 100bps ~ 1Mbps. Operating voltage of 1.8V ~ 3.6V. FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features: - Supply voltage: 1.8 ~ 3.6VDC Code W0077 Available Price €7.24
MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features: - Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Concentration detection: 200ppm - 5000ppm LPG, propane 300ppm - 5000ppm butane 5000ppm - 20000ppm methane 300ppm - 5000ppm H2 100ppm -2000ppm alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0027 Available Price €2.89
MQ-4 Gas Methane Sensor Module for Arduino MQ-4 Gas Methane Sensor Module for Arduino features:- Main chip: MQ-4 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:200ppm- 10000ppm CH4, natural gas- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0028 Available Price €2.95
MG-5 Gas Methane Sensor Module for Arduino MG-5 Gas Methane Sensor Module for Arduino features: - Main chip: MQ-5 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:- 200ppm - 10000ppm LPG, LNG, natural gas, propane,- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0029 Available Price €2.53
ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 features: - To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Uno R3, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip- The seamless mini breadboard has 170 connection points.- You can stick on the shield with its self-adhesive back. Code M0016 Available Regular price €2.20 -€0.21 Price €1.99
Mini Submersible Water Pump DC 3V 120L/H Characteristic: - Operating voltage: 3-6V - Max flow: 80-120 l / h - Maximum pumping height: 40-110cm - Continuous working time of 500 hours - Cable length: 20cm - Inside outlet diameter: 5 mm - Outside outlet diameter: 7.5 mm - Dimensions: 45mm x 23mm x 30mm Code M0040 Available Regular price €2.49 -€0.51 Price €1.98
Plate UNO CH340 + Arduino compatible switches It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader. The Uno R3 module has all connectors than the Arduino Uno R3 and is compatible with all Arduino shields. Plate UNO R3 CH340 + Arduino compatible switches features: - ATmega328P chip at 16MHz with crystal external quartz - ATmega328P microprocessor with socket - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6- 20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader -Atmega328 - SRAM 2 KB - Atmega328 Code B0023 ✗ Out-of-Stock Price €10.99
SIM808 GPRS GSM GPS Bluetooth SIM Quadband SIM808 GPRS GSM GPS Bluetooth SIM Quadband features: - SIM card SIM808 GPRS GSM GPS Bluetooth SIM - Supply voltage range: 3.4-4.4V - Four bands GSM 850/900/1800 / 1900MHz - GPRS multi-slot class 12/10 - GPRS mobile station class B - According to GSM phase 2/2 + - Class 4 (2 W at 850/900 MHz) - Class 1 (1W at 1800 / 1900MHz) - Control by AT commands (3GPP TS 27.007.27.005 and enhanced AT Commands from SIM Com) - Operating temperature: -40 to + 85 ° C - PCB dimension: 38x38mm - GPS sensitivity - Tracking: -165dBm Cold start Sensitivity - Cold start: -147dBm - Time to first solution - Cold start: 30 s - Start to warm up: 28s - Already hot: 1s - Accuracy Code W0069 Available Regular price €19.89 -€3.00 Price €16.89
DIY UNO R3 PCB DIY UNO R3 PCB features: - PCB board for Arduino UNO R3 DIY Code B0020 Backorder Price €0.98
TPA3118 1X60W PBTL Channel Only Amplifier TPA3118 1X60W PBTL Channel Only Amplifier features: - Chip: TPA3118 - Power supply: DC 8V ~ 24V - Channel type: Single channel - Output power: 1 x 60 W. - Matching output: 4 ~ 8 Ohm - Mono PBTL mode - Size (LxWxH): 46 x 35 x 13 mm Code M0036 Available Price €6.46
MPU-6050 Accelerometer Module + Gyroscope 3 Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:- Chip: MPU-6050- Power supply: 3V-5V- Operating current: 5mA- Communication: I2C- 16-bit analog-digital converter on all axes- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)- Dimensions: 14 x 21 x 1.3mm- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin) Code M0017 Available Price €4.29
Rain Sensor Module Water Droplet Detector The module has two outputs: analog A0 and digital D0. digital output D0 - signal 0 or 1 appears depending on the configuration of threshold. The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - digital switching output indicator - Measurements PCB: 3 x 1.5 cm - Sensor measurements: 5.4 x 3.9 cm Code S0022 Available Price €1.69
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 Available Regular price €4.76 -€1.00 Price €3.76
Water Level Sensor Module One Mega Pic Easily convert water level to analog signal The analog output signal can be read directly on the Arduino board Characteristic: - Operating voltage: 3.3V -5 V - Consumption: less than 20 mA - Sensor type: Analog - Operating temperature: 10º C -30º C - Detection area: 40 mm x 16 mm - Dimensions: 60 mm x 20 mm Code S0023 Available Price €1.39
3D Zum Scan Shield + UNO R3 CH340 + A4988 Stepper Feature of 3D Zum shield: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- Content: - 1x Zum Shield 3D - 1x UNO R3 Compatible Arduino - 1x Controller A4988 - 1x Male pin strip - 1x Heatsink for A4988 - 1x USB cable - Jumpers Code I0057 ✗ Out-of-Stock Price €20.90
16 Channel Relay Module 12V 10A This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL, PLC output).16 Channel Relay Module 12V 10A AVR features:- Channels: 16 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 3mA- Insulation: Yes- Low shot: 0-2V- LED indicator: For each channel- Dimensions: 18x 9x 2cm Code RL009 Available Price €15.49
SIM800L GPRS GSM SIM Board Quadband SIM800L GPRS GSM SIM Board Quadband features: Package includes: - SIM800L module, - 2x pin headers, - Spring antenna, - 3G PCB antenna - 15cm cable. - Supported SIM format: Micro SIM. Code W0017 Available Price €6.49
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €9.50
2 Channel Relay Module 5V 10A for Arduino 2 Channel Relay Module 5V 10A for Arduino features:- 5V relay module with 2 optocoupled channels- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 5V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- LED indicator: For each channel- Dimensions: 40x 50mm Code RL006 Available Regular price €1.99 -€0.35 Price €1.64
DHT11 Module Temperature and Humidity Sensor The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables Code S0001 Available Price €2.99
HB100 Microwave Doppler Radar Motion Sensor Microwave motion detector module. The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications. High resistance to radio frequency interference. Characteristic: - Frequency: 10.525GHz - Frequency Accuracy: 3MHz - Minimum Output: 13dBm EIRP - Operating Voltage: 5V ± 0.25V - Operating current (CW): 60mA maximum, 37mA typical - Harmonic emissions: -10dBm - Detection Range: Over 20 meters - Power of Output: 5mW The device is sensitive to electrostatic discharge and can be damaged during welding. The IF output is particularly sensitive. Code M0026 Available Price €5.44
MQ-135 Air Quality Sensor High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases. The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it. MQ-135 Air Quality Sensor features:- Main chip: MQ-135 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 10ppm - 300ppm NH3 10ppm - 1000ppm Benzene 10ppm - 300ppm Alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0034 Available Price €2.45
MQ-9 Carbon Monoxide Sensor Module MQ-9 Carbon Monoxide Sensor Module features:- Main chip: MQ-9 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 20ppm- 2000ppm carbon monoxide 500ppm- 10000ppm methane CH4 500ppm- 10000ppm LPG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0033 Available Price €2.89
MQ-8 Hydrogen Gas Sensor Module MQ-8 Hydrogen Gas Sensor Module features:- Main chip: MQ-8 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 100ppm- 10000ppm hydrogen H2- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0032 Available Price €2.95
MQ-6 Gas Methane Sensor Module for Arduino MQ-6 Gas Methane Sensor Module for Arduino features:- Main chip: MQ-6 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:- 200ppm- 10000ppm LPG, LNG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0030 Available Price €2.59
Micro Usb to DIP Adapter Mini Arduino Module Electronic Converter PCB Micro Usb to DIP Adapter Mini Arduino Module Electronic Converter PCB features: - Compatible with male pin strip (pin spacing 2.54mm) - PCB dimensions: 15mm x 13mm Code M0044 Available Price €0.98
Sensor Module ML8511 UV Sensor Module ML8511 UV features: - The module converts the photocurrent into voltage to detect UV intensity - The analog voltage is proportional to UV light detecting - The has a power saving mode of up to 0.1uA, suitable for smart portable devices or mobile phones for use - Power supply: 5V - Analog output - Captured wavelength: 280-390nm - Ultra low power consumption - Meteorological applications, skincare, industrial UV level measurement - Dimensions of PCB: 30x22mm Code S0040 ✗ Out-of-Stock Price €5.29
Sensor Module GUVA-S12SD UV Sensor Module GUVA-S12SD UV features: - The module based on the Schottky-type photodiode - applicable to the optical mode - This is a " true "UV sensor instead of calibrated light sensor - It has high sensitivity, high stability, good linearity - Power supply: 2.5V - 5V - Analog output - Captured wavelength: 240-370nm - Ultra low power consumption - Meteorological applications, skin care, industrial UV level measurement - PCB dimensions: 11x27mm Code S0041 Available Price €7.99
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.79
Capsule Electret Condenser Microphones 9.5mm MIC Capsule Electret Condenser Microphones 9.5 MIC features: - Measures: 9.7 x 6.7mm- Impedance: 1.5kΩ- Working current: 0.5mA- Working voltage: 4.5V (1.5-10V)- Bandwidth: 50 ... 16000Hz- Signal to noise ratio: ‰¥58dB- Sensitivity: -42 ± 3dB- Sensitivity tolerance: ± 3dB- Distance between terminals: 2.54mm Code M0020 Available Price €0.79
ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 55x 35x 16 mm Code W0002 Available Price €8.99
Joystick Shield compatible with Arduino UNO Mega Shield allows you to be directly punched to an Arduino Uno, Mega board and convert your Arduino board into a controller like the game console system. Joystick Shield compatible with Arduino UNO Mega features: - 3.3V / 5V voltage- 4 large buttons ABCD- 2 small EF buttons- 1 button on the joystick)- 2-axis joystick (x, y)- Nokia 5110 LCD screen interface- Interface nRF24L01 +- Dimensions of PCB: 87 x54 mm Code M0021 Available Price €4.95
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.95
Sound Detection Sensor Module Sound detection module for Arduino projects, smart cars.Sound Detection Sensor Module features:- Adjustable High Sensitivity Acoustic Sensor- Chip LM393- Red LED indicator integrated- Frequency range between 30 and 15000 Hz- Power 4 ~ 6V- Measures 32x16x10mm Code S0002 Available Price €1.69
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €7.49
8 Channel 5V 10A Relay Module Arduino compatible 5V Relay Module with 8 opto-coupled channels. This module can be directly controlled by the microcontroller ( Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). 8 Channel Arduino 5V 10A Relay Module features: - Channels: 8 (independent protected with Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - LED indicator: For each channel - Dimensions: 54x 135mm Code RL008 Available Price €9.49
Led Matrix 8x8 MAX7219 Soldier Led Matrix 8x8 MAX7219 Soldier features: - MAX7219 controller module with 8x8 led matrix + cables - 8X8 LED matrix controlled by MAX7219 chip - Led 3mm red color - SPI communication - Voltage: 4.7 - 5.3V DC - Interfaces to manage multiple modules in cascade - Matrix dimensions: 32mm x 32mm x 8mm - PCB dimensions: 32mm x 50mm Code M0043 Available Price €2.95
TDA2030A 1X18W Audio Amplifier TDA2030A 1X18W Audio Amplifier features: - Chip: TDA2030A - Power supply: DC 6V ~ 12V - Channel type: Single channel - Output power: 1 x 18 W - Output output: 4 ~ 8 Ohm - Mono mode - Size (LxWxH): 31.6 x 23.5 mm Code M0063 Available Regular price €3.39 -€1.00 Price €2.39
NFC RFID Keychain Tag 13.56 MHz NFC RFID Keychain Tag 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with NFC Mifare 1k - Memory: 1kB EEPROM - Operating frequency: 13.56MHZ - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20ºC to 85ºC - Number of uses 100,000 times - Data retention: 10 years - Material: ABS - Dimensions 40.5 x 32 x 4.2 mm Code M0030 Available Price €0.99
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.99
TDA7498 Class D 2X100W Amplifier Characteristic: - Quiescent current: 50 mA (without load) - Efficiency: 90% - Nominal output power max.: 2 x 100W - Frequency response: 20Hz to 20KHz - Operating voltage: DC20V to DC34V - Recommended supply voltage: DC32V - Speaker parameters: 6 Ohm , 8 Ohm - PCB board size: 87 × 72 mm - Package includes cable Code M0035 ✗ Out-of-Stock Price €19.51
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 Available Price €5.39
USB DC 5V Bluetooth Audio USB DC 5V Bluetooth Audio features: - You can connect it with your smartphone - Power: DC 5V micro USB - Speaker: 4 ~ 8 Ohm - Audio Jack: 3.5mm - SD card: support MP3 / WMA / WAV / FLAC format - The transmission distance could be up to 10m - Size: 50 x 40 mm Code M0067 ✗ Out-of-Stock Price €5.79
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €3.09
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Last items in stock Price €44.95
HC-SR505 Mini Module Motion Detector Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 3 meters. One sensor electric pyro, which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. Characteristic: - Operating voltage: 4.5V- 20V - Consumption in idle state: Code S0037 Available Price €2.70
PAM8403 2x3W Digital Amplifier Channel Stereo PAM8403 2x3W Digital Amplifier Channel Stereo features: - Up to 3W in each channel- Chip: PAM8403- Power supply: 5V- Power: 2 outputs of 3 watts each- Measures: 21x18 mm- Suitable impedance speakers: 4 Ohm Code M0027 Available Price €1.89
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €5.39
Water Flow Sensor 1-30l /Min YF-S201 The meter built on the basis of a water rotor and a Hall effect sensor Please note this is not a Accuracy. Pulse rate varies slightly depending on flow rate, fluid pressure, and sensor orientation. Water Flow Sensor 1-30l /Min YF-S201 features: - Working voltage range: DC 5 ~ 18 V - Allow pressure: water pressure below 1.75Mpa - Accuracy (flow-pulse output): ± 1 ~ 30 l / min - Use temperature: ‰ ¤ 80 ° C - Load capacity: ‰ ¤ 10 mA (5Vdc) - Operating humidity: 35% ~ 90% RH (frost free) - Temperature: -25 ~ + 80 ° C - Outlet diameter: 1/2 " - Red wire: positive supply - Wire Black: negative power supply - Yellow Cable: signal output - Color: black - Size: 6.2x3.6x3.4 cm Code M0109 ✗ Out-of-Stock Price €5.95
TCRT5000 IR Infrared Sensor Module The optical module (reflective) sensor with CMOS Schmitt inverter 74HC14D, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. The sensor allows the detection of an object at a distance of up to 15 mm. TCRT5000 IR Infrared Sensor Module features: - The module has an output: digital - CMOS Schmitt inverter 74HC14D - Power supply: 5V - Range: 0.2 mm - 15 mm Code S0048 Available Price €1.49
HX711 Module Weighing Pressure Sensor 24 Bits The module uses a 24-bit high precision A/D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. HX711 Module Weighing Pressure Sensor 24 Bits features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0118 Available Regular price €2.79 -€0.47 Price €2.32
Edup Mini Dongle WiFi USB For pcDuino 3 Nano Raspberry Pi Edup Mini Dongle WiFi USB For pcDuino 3 Nano Raspberry Pi features: - Interface type: USB - Supports IEEE 802.11e draft 802.11n - Supports USB 2.0, compatible with USB 1.1 and 1.2 - Support systems: - Win2k / XP / Vista / Win7 / Win8.1 / Win10 / Mac / Linux - Operating distance: 91 meters indoors, 275 meters in open space - Transfer rate: 150Mbps (downlink) and 150Mbps (uplink) - Works with old Wireless-G and Wireless-B networks - WEP and WPA encryption - 64-bit / 128-bit WEP (Wired Equivalent Privacy), TKIP, AES 2,400GHz ISM - Frequency range: 2.4 to 2.4835 GHz - Operating channels: 13 - Support network protocol: CSMA / CA with acknowledgment - Transmission mode: DSSS Code RA015 Available Regular price €8.49 -€2.00 Price €6.49