Solar panel DIY 6V 1W Solar panel DIY 6V 1W features: - Mobile DIY Solar System Photovoltaic Charger Cell - Working voltage: 6V - Output power: 1W - Working current: 0-200 mA - Product size: 110x60x3 mm Code A0062 Available Price €3.26
Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €7.40
ESP-01 Esp-01 Esp8266 ESP01 WiFi USB Programmer Adaptor USB adapter that allows a direct USB connection to your ESP8266 ESP-01 or ESP-01S WiFi module. Based on the CH340 integrated circuit, which is a USB - Serial converter (UART). Code W0110 Available Price €2.60
5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat The 28BYJ-48 has everything you need to start using stepper motors in your projectA stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller cardCan control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mAEquipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features: - Engine model: 28BYJ-48- Phases engine: 4- Operating voltage: 5V- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 ohm- Angle per step: 5,625º- Steps per round: 64- Torque: 0.3 Kgr / cm- Speed: 1900 rpm Code R0038 Available Price €2.44
Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.07
10x MALE CABLES 10cm Male Jumpers Dupont 2,54 10x MALE CABLES 10cm Male Jumpers Dupont 2,54 features: -Length: 10cm -Quantity: 10 wires -Dupont male connectors on both ends -Compatible with 2.54mm female connectors -High quality and good working condition -Easy to install and use Code K0168 Available Price €0.10
USB DC 5V Bluetooth Audio USB DC 5V Bluetooth Audio features: - You can connect it with your smartphone - Power: DC 5V micro USB - Speaker: 4 ~ 8 Ohm - Audio Jack: 3.5mm - SD card: support MP3 / WMA / WAV / FLAC format - The transmission distance could be up to 10m - Size: 50 x 40 mm Code M0067 ✗ Out-of-Stock Price €4.79
Wireless Module Arduino compatible HC-05 HC05 Bluetooth The bluetooth HC-05 module is one of the best options for projects where you need wireless communications. The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features: - CSR BC417 Chipset - Power: 3.3. - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz ISM band - Modulation: GFSK - Approximate range: 10m - Security: Authentication and encryption - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port temperature: -20 ºC to +75 ºC Code W0019 Available Price €7.36
Bluetooth Decoder Module Amplifier Audio Receiver USB TF This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features: - Interfaces: - 5V micro USB supply - USB audio - U disk - LED - TF card - IR remote - AD key interface to connect external circuits - Bluetooth decoder - 3.5mm stereo output - Left and right 3W channels handling speaker - 2 3W amplifiers- Supply voltage: 3.7-5VDC- Signal / noise ratio (SNR): 90 dB Code W0084 Available Price €4.88
SparkFun ESP32 Thing The SparkFun ESP32 thing is an upgrade to boards based on the popular ESP8266. What the 32 version has to offer on top? Well one of the largest upgrades is support for Bluetooth communications and nearly 30 I/O pins. Makes it pretty perfect for any IoT solution, right? Code SP009 Last items in stock Price €23.13
XM-15B Bluetooth Serial Port Module Master Slave Arduino compatible HC-05/06 XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features: * Power 3.0V -6V* 3.3V / 5V logic levels* Bluetooth version V2.1 + EDR* Frequency: 2.4GHz ISM band* Reach approx. 30m* Security: Authentication and encryption* Supports AT commands for configuration through a serial port* Working temperature: -20 ºC to +75 ºC* Working current - 50 mA* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)- Built-in hardware protector, never hangs Code W0022 Available Price €6.19
SparkFun IoT RedBoard - ESP32 Development Board SparkFun IoT RedBoard development board compatible with Arduino. It incorporates an ESP32 chip with a 32-bit dual-core Xtensa LX6 microprocessor with a clock frequency of up to 240 MHz. It enables WiFi and Bluetooth wireless communication, making it versatile for Smart Home and IoT projects. Code SP048 Available Price €37.60
Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE - Bluetooth 4.0 AT-09 BLE Master / Slave module with 6-pin connection base - This module is very similar to HM-10 module - Bluetooth protocol: Bluetooth V4.0 BLE specification - Ultra-low power consumption, in 90uA standby mode Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE features: - Chipset based on CC2541 - Bluetooth Class 2 - Industrial level Bluetooth module SPP - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) Code W0078 Available Price €4.09
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 Available Price €4.45
BLE 4.0 UART Bluetooth Low Energy Module without Adapter This product is a Bluetooth module BLE 4.0 UART without adapter, low energy with serial transceiver.Logic level conversion circuit. No external level of 5V is needed to become a 3.3V level.The power input port is protected against the anti-circuit, to avoid the inverted accidental power plug, which leads to the module burnHM-10, Bluetooth module HM-11 series using IT chip CC2540 / 2541, configuration 256Kb space, supportIn commands.You can change the paper (master and slave mode) and the baud rate, the device name, the pairing of the password and other parameters, convenient and flexible. BLE 4.0 UART Bluetooth Low Energy Module without Adapter features: - Version AT-09 CC2541 Arduino Android IOS BLE- Serial transceiver Code W0087 Available Price €4.39
Bluetooth Wireless Module 4.0 CC2541 Android IOS HM-10 BLE for Arduino Bluetooth protocol: Bluetooth V4.0 BLE specification. Ultra-low power consumption, in 60uA standby mode. Half open and iPhone can reach 100 meters extreme communication distance. Arduino Bluetooth Wireless Module 4.0 CC2541 Android IOS HM-10 BLE features: - Chipset based on CC2541 TI - Bluetooth Class 2 - Industrial level Bluetooth SPP module - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) - 40 channels, 2MHz, 3 transmission channels Fixed, 37 automatic frequency adaptation skipping data channels; Code W0008 Available Price €14.79
USB DC 5V Bluetooth Audio USB DC 5V Bluetooth Audio features: - You can connect it with your smartphone - Power: DC 5V micro USB - Speaker: 4 ~ 8 Ohm - Audio Jack: 3.5mm - SD card: support MP3 / WMA / WAV / FLAC format - The transmission distance could be up to 10m - Size: 50 x 40 mm Code M0067 ✗ Out-of-Stock Price €4.79
Wireless Module Arduino compatible HC-05 HC05 Bluetooth The bluetooth HC-05 module is one of the best options for projects where you need wireless communications. The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features: - CSR BC417 Chipset - Power: 3.3. - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz ISM band - Modulation: GFSK - Approximate range: 10m - Security: Authentication and encryption - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port temperature: -20 ºC to +75 ºC Code W0019 Available Price €7.36
Bluetooth Decoder Module Amplifier Audio Receiver USB TF This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features: - Interfaces: - 5V micro USB supply - USB audio - U disk - LED - TF card - IR remote - AD key interface to connect external circuits - Bluetooth decoder - 3.5mm stereo output - Left and right 3W channels handling speaker - 2 3W amplifiers- Supply voltage: 3.7-5VDC- Signal / noise ratio (SNR): 90 dB Code W0084 Available Price €4.88
SparkFun ESP32 Thing The SparkFun ESP32 thing is an upgrade to boards based on the popular ESP8266. What the 32 version has to offer on top? Well one of the largest upgrades is support for Bluetooth communications and nearly 30 I/O pins. Makes it pretty perfect for any IoT solution, right? Code SP009 Last items in stock Price €23.13
XM-15B Bluetooth Serial Port Module Master Slave Arduino compatible HC-05/06 XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features: * Power 3.0V -6V* 3.3V / 5V logic levels* Bluetooth version V2.1 + EDR* Frequency: 2.4GHz ISM band* Reach approx. 30m* Security: Authentication and encryption* Supports AT commands for configuration through a serial port* Working temperature: -20 ºC to +75 ºC* Working current - 50 mA* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)- Built-in hardware protector, never hangs Code W0022 Available Price €6.19
SparkFun IoT RedBoard - ESP32 Development Board SparkFun IoT RedBoard development board compatible with Arduino. It incorporates an ESP32 chip with a 32-bit dual-core Xtensa LX6 microprocessor with a clock frequency of up to 240 MHz. It enables WiFi and Bluetooth wireless communication, making it versatile for Smart Home and IoT projects. Code SP048 Available Price €37.60
Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE - Bluetooth 4.0 AT-09 BLE Master / Slave module with 6-pin connection base - This module is very similar to HM-10 module - Bluetooth protocol: Bluetooth V4.0 BLE specification - Ultra-low power consumption, in 90uA standby mode Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE features: - Chipset based on CC2541 - Bluetooth Class 2 - Industrial level Bluetooth module SPP - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) Code W0078 Available Price €4.09
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 Available Price €4.45
BLE 4.0 UART Bluetooth Low Energy Module without Adapter This product is a Bluetooth module BLE 4.0 UART without adapter, low energy with serial transceiver.Logic level conversion circuit. No external level of 5V is needed to become a 3.3V level.The power input port is protected against the anti-circuit, to avoid the inverted accidental power plug, which leads to the module burnHM-10, Bluetooth module HM-11 series using IT chip CC2540 / 2541, configuration 256Kb space, supportIn commands.You can change the paper (master and slave mode) and the baud rate, the device name, the pairing of the password and other parameters, convenient and flexible. BLE 4.0 UART Bluetooth Low Energy Module without Adapter features: - Version AT-09 CC2541 Arduino Android IOS BLE- Serial transceiver Code W0087 Available Price €4.39
Bluetooth Wireless Module 4.0 CC2541 Android IOS HM-10 BLE for Arduino Bluetooth protocol: Bluetooth V4.0 BLE specification. Ultra-low power consumption, in 60uA standby mode. Half open and iPhone can reach 100 meters extreme communication distance. Arduino Bluetooth Wireless Module 4.0 CC2541 Android IOS HM-10 BLE features: - Chipset based on CC2541 TI - Bluetooth Class 2 - Industrial level Bluetooth SPP module - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) - 40 channels, 2MHz, 3 transmission channels Fixed, 37 automatic frequency adaptation skipping data channels; Code W0008 Available Price €14.79