Battery holder 2x 18650 3,7V Serial

Prototype Protoboard Breadboard 170 points Arduino features:
- 170 connections
- Base with adhesive to attach it to the work surface
- Measurements: 45x35x9mm
- Various colors

Ideal to build a car with an obstacle detector, light follower Characteristic: - Voltage: 3 to 6Vdc
- No load speed: 100 RPM to 6Vdc
- No load current: 90mA to 3Vdc - 180mA to 6Vdc
- Wheel dimensions: diameter 65mm - width 26mm The kit includes: - aluminum platform - 2x wheels and 2x motors - 1x idler wheel - screws

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

Metal casing with Internal magnet Characteristic: - Power 2-3W
- Impedance: 4 Ohm - Shape: Round - Thickness: 5.3mm / 0.21 " - Diameter: 40mm / 1.6" - Quantity: 1 unit

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

1N4007 Rectifier Diodes 1A 1000V DO-41 features:
- Standard rectifier diode
- Configuration: Simple
- Reverse voltage: 1000V
- Direct voltage drop: 1V
- Direct direct current: 1A
- Maximum overvoltage current: 30A
- Encapsulated: DO-41
- Operational tension: -65ºC to + 125ºC
- Quantity: 30 units

Jack connectors 2.1mm inside and 5.5mm outside to power devices such as LED strips, CCTV (Cameras), Arduino. Connector Jack 2.1x5.5mm Power Supply DC Male features:
- Ideal for connecting without welding
- It has two screws in the tip for positive and negative cable screwdriver

The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement.
Characteristic:
- Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds - Working current 2.5mA
- 1-wire interface
- Dimensions: 32 x14 mm
- Quantity: 1 unit with 3x female / female cables