MB102 Prototype Board + 65x Jumper Cable + Power Module 3.3V 5V for Arduino MB-102 Prototype Board + 65x Jumper Cable + Power Module 3.3V 5V Arduino features: * 65 Male-Male jumper cables: -Cable lengths: 120mm, 150mm, 200mm, 240mm * MB-102 breadboard: -830 Connections -Measures 165x55x8 mm * Module: -Input voltage up to 12V -Maximum current 700mA Code PB006 Available Price €7.89
Rechargeable battery 9V 6F22 Ni-MH 250 mAh Ready to Use Rechargeable battery 9V 6F22 Ni-MH 250 mAh Ready to Use features: Code PP049 Available Price €5.99
Module Relay 12V Light sensor LDR This module is a three-way switch (COM, NO and NC) that uses the intensity of the ambient light to directly control the output load. Its adjustment potentiometer allows you to change the sensitivity and set the threshold for starting the relay. The relay is energized when it is darker than the threshold. The optical isolation relay effectively protects the chip and ensures better performance. This module is used for light detection, brightness detection , control of lamps and automatic equipment. Characteristic: - Channels: 1 - Supply voltage: 12VDC - Output load capacity: 250V 10A AC / 30V 10A DC - Relay activation current: & gt; 100mA - Insulation: Yes - Indicator LED: Green and Red - PCB size: 5x2.6 cm / 1.96x1.02 " Code RL019 Available Price €3.49
Batch of 600 Units 1/4W Resistors Various values Ohm Ω Batch of 600 Units 1/4W Resistors Various values Ohm Ω features: - Each lot contains (30 x 20 units): 10Ω, 22Ω, 47Ω, 100Ω, 150Ω, 200Ω, 220Ω, 270Ω, 330Ω, 470Ω, 510Ω, 680Ω, 1KΩ, 2KΩ, 2.2KΩ, 3.3KΩ, 4.7KΩ, 5.1KΩ, 6.8KΩ, 10KΩ, 20KΩ, 47KΩ, 51KΩ, 68KΩ, 100KΩ , 220KΩ, 300KΩ, 470KΩ, 680KΩ, 1M - Tolerance: ± 5% - Power: 0.25W Code D0070 Available Price €3.95
DIP Switch - DS-06 Horizontal High Profile 6 Positions The DIP switch type THT (6 rows 12 Pins) with a pitch of 2.54mm / 0.1 ". It works with the current of 50mA DC 12V. Code K0266 Available Price €0.99
DC 15V Analog Panel Voltmeter 0 to 15V Round DC 15V Analog Panel Voltmeter 0 to 15V Round features: - 15V 0-15V DC analog voltage panel meter- Type: Analog voltage meter- Range of scale: DC 0-15V- Accuracy: Class 2.5- Complete with screws for simple DIY installation Code H0158 Available Price €3.69
Buzzer 5V Active Buzzer 4 to 7V DC Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects. Buzzer 5V Active Buzzer 4 to 7V DC features: - Input voltage: 4V to 7V - Diameter: 12mm - Height: 9.5mm - Spacing Pins: 7.6mm - Maximum Current: Code M0007 Available Price €0.45
USBASP Atmega8 AVR Programmer Atmega128 Arduino compatible Adapter Cable Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1 - LED status indicators - Transmission speed: 5kB / s - Fuse protector against possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦ Code B0029 Available Price €6.59
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 Available Price €7.99
BLE 4.0 UART Bluetooth Low Energy Module without Adapter This product is a Bluetooth module BLE 4.0 UART without adapter, low energy with serial transceiver.Logic level conversion circuit. No external level of 5V is needed to become a 3.3V level.The power input port is protected against the anti-circuit, to avoid the inverted accidental power plug, which leads to the module burnHM-10, Bluetooth module HM-11 series using IT chip CC2540 / 2541, configuration 256Kb space, supportIn commands.You can change the paper (master and slave mode) and the baud rate, the device name, the pairing of the password and other parameters, convenient and flexible. BLE 4.0 UART Bluetooth Low Energy Module without Adapter features: - Version AT-09 CC2541 Arduino Android IOS BLE- Serial transceiver Code W0087 Available Price €5.31
Mini Dongle Adapter Bluetooth USB V2.0 Windows XP/VISTA/7 Work with Bluetooth compliant devices including notebook, PDA, digital camera,printer and mobile phone.Mini Dongle Adapter Bluetooth USB V2.0 Windows XP/VISTA/7 features:- Bluetooth specification V2.0 - Supporting profiles: networking, dial-up, fax, LAN access and handset - Operation system Windows98, 98se, Me, 2000, XP, Vista, Windows7 - Receiving/sending range: 100m Code W0093 Available Price €3.90
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €7.99
XM-15B Bluetooth Serial Port Module Master Slave Arduino compatible HC-05/06 XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features: * Power 3.0V -6V* 3.3V / 5V logic levels* Bluetooth version V2.1 + EDR* Frequency: 2.4GHz ISM band* Reach approx. 30m* Security: Authentication and encryption* Supports AT commands for configuration through a serial port* Working temperature: -20 ºC to +75 ºC* Working current - 50 mA* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)- Built-in hardware protector, never hangs Code W0022 Backorder Price €5.64
Bluetooth Wireless Module 4.0 CC2541 Android IOS HM-10 BLE for Arduino Bluetooth protocol: Bluetooth V4.0 BLE specification. Ultra-low power consumption, in 60uA standby mode. Half open and iPhone can reach 100 meters extreme communication distance. Arduino Bluetooth Wireless Module 4.0 CC2541 Android IOS HM-10 BLE features: - Chipset based on CC2541 TI - Bluetooth Class 2 - Industrial level Bluetooth SPP module - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) - 40 channels, 2MHz, 3 transmission channels Fixed, 37 automatic frequency adaptation skipping data channels; Code W0008 Available Price €17.89
Wireless Module Arduino compatible HC-05 HC05 Bluetooth The bluetooth HC-05 module is one of the best options for projects where you need wireless communications. The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features: - CSR BC417 Chipset - Power: 3.3. - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz ISM band - Modulation: GFSK - Approximate range: 10m - Security: Authentication and encryption - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port temperature: -20 ºC to +75 ºC Code W0019 Available Price €8.90
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €9.50
Low power Bluetooth / Multi-standard SensorTag CC2650STK TI The new SensorTag IoT kit invites you to realize your product idea connected to the cloud. The new SensorTag now includes 10 low-power MEMS sensors in a small red package. And it's expandable with DevPacks to make it easy to add your own sensors or actuators. Connect to the cloud with low-power Bluetooth and Get your sensor data online in 3 minutes. The SensorTag is ready to go right away with an iOS and Android app, no programming experience to get started. The new SensorTag is based on The CC2650 Wireless MCU, which offers 75% less power consumption than previous Bluetooth low energy products. This allows the SensorTag to run on batteries, and offers years of battery life with a single coin cell battery. Code W0088 Backorder Price €45.00
Bluetooth Decoder Module Amplifier Audio Receiver USB TF This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features: - Interfaces: - 5V micro USB supply - USB audio - U disk - LED - TF card - IR remote - AD key interface to connect external circuits - Bluetooth decoder - 3.5mm stereo output - Left and right 3W channels handling speaker - 2 3W amplifiers- Supply voltage: 3.7-5VDC- Signal / noise ratio (SNR): 90 dB Code W0084 Available Price €6.98
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 Available Price €7.99
BLE 4.0 UART Bluetooth Low Energy Module without Adapter This product is a Bluetooth module BLE 4.0 UART without adapter, low energy with serial transceiver.Logic level conversion circuit. No external level of 5V is needed to become a 3.3V level.The power input port is protected against the anti-circuit, to avoid the inverted accidental power plug, which leads to the module burnHM-10, Bluetooth module HM-11 series using IT chip CC2540 / 2541, configuration 256Kb space, supportIn commands.You can change the paper (master and slave mode) and the baud rate, the device name, the pairing of the password and other parameters, convenient and flexible. BLE 4.0 UART Bluetooth Low Energy Module without Adapter features: - Version AT-09 CC2541 Arduino Android IOS BLE- Serial transceiver Code W0087 Available Price €5.31
Mini Dongle Adapter Bluetooth USB V2.0 Windows XP/VISTA/7 Work with Bluetooth compliant devices including notebook, PDA, digital camera,printer and mobile phone.Mini Dongle Adapter Bluetooth USB V2.0 Windows XP/VISTA/7 features:- Bluetooth specification V2.0 - Supporting profiles: networking, dial-up, fax, LAN access and handset - Operation system Windows98, 98se, Me, 2000, XP, Vista, Windows7 - Receiving/sending range: 100m Code W0093 Available Price €3.90
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €7.99
XM-15B Bluetooth Serial Port Module Master Slave Arduino compatible HC-05/06 XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features: * Power 3.0V -6V* 3.3V / 5V logic levels* Bluetooth version V2.1 + EDR* Frequency: 2.4GHz ISM band* Reach approx. 30m* Security: Authentication and encryption* Supports AT commands for configuration through a serial port* Working temperature: -20 ºC to +75 ºC* Working current - 50 mA* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)- Built-in hardware protector, never hangs Code W0022 Backorder Price €5.64
Bluetooth Wireless Module 4.0 CC2541 Android IOS HM-10 BLE for Arduino Bluetooth protocol: Bluetooth V4.0 BLE specification. Ultra-low power consumption, in 60uA standby mode. Half open and iPhone can reach 100 meters extreme communication distance. Arduino Bluetooth Wireless Module 4.0 CC2541 Android IOS HM-10 BLE features: - Chipset based on CC2541 TI - Bluetooth Class 2 - Industrial level Bluetooth SPP module - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) - 40 channels, 2MHz, 3 transmission channels Fixed, 37 automatic frequency adaptation skipping data channels; Code W0008 Available Price €17.89
Wireless Module Arduino compatible HC-05 HC05 Bluetooth The bluetooth HC-05 module is one of the best options for projects where you need wireless communications. The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features: - CSR BC417 Chipset - Power: 3.3. - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz ISM band - Modulation: GFSK - Approximate range: 10m - Security: Authentication and encryption - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port temperature: -20 ºC to +75 ºC Code W0019 Available Price €8.90
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €9.50
Low power Bluetooth / Multi-standard SensorTag CC2650STK TI The new SensorTag IoT kit invites you to realize your product idea connected to the cloud. The new SensorTag now includes 10 low-power MEMS sensors in a small red package. And it's expandable with DevPacks to make it easy to add your own sensors or actuators. Connect to the cloud with low-power Bluetooth and Get your sensor data online in 3 minutes. The SensorTag is ready to go right away with an iOS and Android app, no programming experience to get started. The new SensorTag is based on The CC2650 Wireless MCU, which offers 75% less power consumption than previous Bluetooth low energy products. This allows the SensorTag to run on batteries, and offers years of battery life with a single coin cell battery. Code W0088 Backorder Price €45.00
Bluetooth Decoder Module Amplifier Audio Receiver USB TF This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features: - Interfaces: - 5V micro USB supply - USB audio - U disk - LED - TF card - IR remote - AD key interface to connect external circuits - Bluetooth decoder - 3.5mm stereo output - Left and right 3W channels handling speaker - 2 3W amplifiers- Supply voltage: 3.7-5VDC- Signal / noise ratio (SNR): 90 dB Code W0084 Available Price €6.98