Bluetooth Decoder Module Amplifier Audio Receiver USB TF
  • Bluetooth Decoder Module Amplifier Audio Receiver USB TF
  • Bluetooth Decoder Module Amplifier Audio Receiver USB TF
  • Bluetooth Decoder Module Amplifier Audio Receiver USB TF
  • Bluetooth Decoder Module Amplifier Audio Receiver USB TF

Bluetooth Decoder Module Amplifier Audio Receiver USB TF

W0084

This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.
Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features:
- Interfaces:
       - 5V micro USB supply
       - USB audio
       - U disk
       - LED
       - TF card
       - IR remote
       - AD key interface to connect external circuits
       - Bluetooth decoder
       - 3.5mm stereo output
       - Left and right 3W channels handling speaker
       - 2 3W amplifiers
- Supply voltage: 3.7-5VDC
- Signal / noise ratio (SNR): 90 dB

OEM
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Bluetooth Decoder Module Amplifier Audio Receiver USB TF description


This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.
Its remote control allows you to control the audio output (volume down or up, music change, mode change).

Bluetooth Decoder Module Amplifier Audio Receiver USB TF features:


- Interfaces:
       - 5V micro USB supply
       - USB audio
       - U disk
       - LED
       - TF card
       - IR remote
       - AD key interface to connect external circuits
       - Bluetooth decoder
       - 3.5mm stereo output
       - Left and right 3W channels handling speaker
       - 2 3W amplifiers
- Supply voltage: 3.7-5VDC
- Signal / noise ratio (SNR): 90 dB
- Harmonic distortion (THD + N): -70dB
- Interference (Crosstalk): -86dB
- Compatible profiles: A2DP / AVCTP / AVDTP / AVRCP / HFP
- Digital noise reduction (DNR): 91dB
- Loss of signal:> 15m
- PCB size: 4.6x4.0 cm / 1.81x1.57 "

Data sheet

Chip
Otro
Pines
Sin pines

Customers who bought this product also bought

SONOFF SNZB-03 - ZigBee Motion Sensor

SONOFF SNZB-03 is a stylish mini wireless motion sensor via ZigBee, through its Bridge (required). Detection distance of 6m and viewing angle of 110°. Detects motion and triggers alert messages.

WS035

Regular price €8.18 -€0.91 Price €7.27

SONOFF ZBBridge-P - Smart Zigbee Bridge Pro

The SONOFF ZigBee Bridge Pro is the heart of the smart home that allows you to remotely manage a variety of ZigBee devices and sensors to monitor and control the home. Compared to the previous version, the new ZBBridge-P allows the operation of up to 128 devices. In addition, it is equipped with an alarm control unit function. It is compatible with the new ZBMINI-L smart switch and S26R2ZB smart plug products, allowing you to easily automate your home.  Interact with all your Sonoff devices, both WiFi and ZigBee, thanks to this bridge.

WS078

Regular price €20.65 -€5.00 Price €15.65

Battery LIPO 190mAh 3.7V 2 cables

LITHIUM POLYMER BATTERY Battery LIPO 190mAh 3.7V features:
-Battery type-lithium polymer. - Type of battery terminals- 3 cables. -Voltage of the battery-3.7 V -Capacity of the battery- 190 mAh. - Embedded PCM security chip (protection against overload, over discharge, short circuit). Dimensions: -Battery length / depth- 33 mm -Battery width / diameter- 44 mm It has three cables with a 3-pin connector with a separation of 2 mm. Cables: Red: positive. Black: negative. Yellow: thermistor output.

PP109

Regular price €2.88 -€0.30 Price €2.58

8A DC Step-down Converter 8-40V to 1.25-35V Current Control XL4016

A high-performance regulator-booster.
24V battery charger - DC / CV method.
Power supply of the laptop from a 12V car battery.
A high-performance dimmer-regulator.
Charger for Li-Ion, Li-Po batteries etc. - CC / CV method.
LED Constant current driver for LED diodes.
Characteristic:
- Input voltage: 6V -40V
- Output voltage: 1.25-35V (adjustable)
- Output current: 8A, (10A maximum)
- Output power: 300W maximum
- Efficiency of Conversion: up to 95%
- Wiring: Solderless terminal
- Operating frequency: 300kHz
- Ambient temperature exceeds 40 ° C, increase heat dissipation
- LED indicator two-color;
- Charge red
- Fully charged light green
- No charge green

A0011

Price €6.57

4S BMS 25A 16.8V 18650 PCM PCB Circuit Charging Module

In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge.

A0107

Price €3.79

3A DC Converter 4-53V Adjustable LM2596H Step Down Source

Wide range of voltages, improved version.
Drop module.
They will use a multimeter to Check the output voltage and adjust the potentiometer.
3A DC Converter 4-53V Adjustable LM2596H Step Down Source features:

- Based on the LM2596HVS-ADJ regulator
- Rectification: Asynchronous
- Output Voltage: 3v ~ 40v DC (adjustable)
- Input Voltage: 4.5v - 53v DC
- Max Output Current: 3A (with heat sink)
- Ripple in output voltage: 30mV
- Frequency: 150KHz
- Max Conversion Efficiency: 92%
- Load Regulation: ± 0.5% - Voltage Regulation: ± 2,5%
- Operating temperature: -40ºC to + 85ºC
- Measurements: 43x 21x 14 mm

A0018

Price €2.31

NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz

NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features:
- Standard: NFC Forum Type2 Tag Ntag215
- Protocol: ISO14443A
- Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ
- Reading distance: 0-10CM
- Communication speed: 106Kboud
- Working temperature: -20ºC to 70ºC
- Number of uses 100,000 times
- Data retention: 10 years
- Material: PVC
- Dimensions 86 x 54 x 0.84 mm

M0052

Price €1.64

Battery LIPO 180mAh 3.7V

LITHIUM POLYMER BATTERY Battery LIPO 180mAh 3.7V features:
-Battery type-lithium polymer. -Type of battery terminals- 3 wires. -Voltage of the battery-3.7 V -Capacity of the battery- 180 mAh. - Embedded PCM security chip (protection against overload, over discharge, short circuit Dimensions: -Length / depth of the battery- 20 mm -Battery width / diameter -31 mm It has three cables with a 3-pin connector with a separation of 2 mm. Wires: Red: positive. Black: negative. Yellow: thermistor output. The technical file: Battery LIPO.pdf

PP038

Price €2.88
€4.88

4,88 tax excl.

1
Last 2 items
Price €4.88

Order until 4pm we will send today
30 days return