8 Channel 5V 10A Relay Module Arduino compatible

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

The Ethernet module for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the local network and internet based WIZNET with a TCP/IP interface. Compatible with libraries with the same Ethernet API. A web server can be built with this UNO board shield. It can be used as a server or as a client.

Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
It serves to measure the static acceleration, for example gravity, in applications where you need to measure the inclination.
Also to measure dynamic acceleration, movement. ADXL345 3-Axis Accelerometer SPI and I2C features:
- Type: 3-axis accelerometer
- Chip: ADXL345
- Supply voltage: 3-5V
- Consumption: 40uA active and 0.1uA on hold
- Communication: SPI and I2C
- Measurements: Static and dynamic acceleration
- Accelerometer scales ± 2g, ± 4g, ± 8g and ± 16g
- Resolution: 13 bits
- Dimensions: 20x16mm
- Operating temperature: -40 °C to +80 °C
- Detection: Free fall, click-double click

Heat Shrinkable Tube 5 Colors 3 Meters Package features:
- Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas.
- These heat shrink tubes are very flexible and of high quality. Made in EU
- Different sizes of 20 cm each are delivered:
* 1,6mm: black, brown, red, yellow, orange
* 2,4mm: black, brown , red, yellow, blue
* 3,2mm: black, brown, red, yellow, blue
- Quantity: 15 units
- Material: polyolefin
- Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter)
- Minimum shrinkage temperature: 115 ° C maximum 200 ° C

Integrated Circuit Supports DIP28 Width 10.16 mm features:
- Type: DIP DIL
- Total number of pins: 28
- Step between pins: 2.54 mm
- Material: Polybutylene terephthalate
- Length: 33.02 mm
- Width: 10.16 mm
- Min temperature: -25 °C
- Max temperature: +85 °C
- Compliant with the RoHS standard

28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:
- Stepper motor 28BYJ-48 + ULN2003 controller
- The 28BYJ-48 has everything you need to start using motors step by step in your project
- A stepper motor converts digital impulses into small steps of movement in one direction
- The motor also comes with a ULN2003 motor controller card
- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA
- Equipped with state indicator LEDs A, B, C, D
- Engine model: 28BYJ-48
- Phasing Engine: 4
- Operating voltage: 12V DC
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 Ohm
- Angle per step: 5,625º
- Steps per round: 64

Resistors Kit 5% 0,25W 1/4W features:
 
-10 pcs - 100 Ohm
-10 pcs - 220 Ohm
-10 pcs - 1,0k Ohm
-10 pcs - 2,2k Ohm
-10 pcs - 4,7k Ohm
-10 pcs - 10k Ohm
-10 pcs - 100k Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

W1209 12V DC Thermostat Digital Temperature Controller Switch features:
- Model: W1209
- Supply voltage: DC 12V
- Temperature control mode: ON / OFF
- Temperature range: -50 -110 ° C
- Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C
- Measurement accuracy: 0.1 ° C
- Refresh rate: 0.5 s
- Temperature protection 0-110 ° C
- Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA
- Power of output: 10A relay
- Sensor probe: NTC waterproof sensor (10K 0.5%)
- Environmental requirements: -10 ~ 60 ° C Humidity 20% -85%
- Dimensions: 48 x 40 mm