SparkFun Triple Axis Accelerometer Breakout - LIS331 This board features and extremely low power LIS331HH accelerometer. The unit is a MEMS three axis linear accelerometer with a I2C- SPI serial interface enabling use with embedded applications. The range of measurement includes three options +-6g/+-12g/+-24g and enables datalogging with output rates fro 0.5 Hz to 1kHz. Check this and plenty of other accelerometers in our offering of both Sparkfun and other producers Code SP003 Available Price €18.95
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (wo headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached It is a version without headers of a popular BOB-09868 from SparkFun. In our offer, we have a versuib with headers (SP0001) and with QWIC system (SP0005). Code SP004 Last items in stock Price €16.99
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (Qwiic) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. It comes with QWIIC connectors Code SP005 Last items in stock Price €14.99
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €21.99
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €23.99
SparkFun MEMS Microphone Breakout - INMP401 (ADMP401) - obsolete Ever needed a microphone for your project. This tiny little board will fulfill all your needs - it is not only mobile, but as well easy to connect. A low power, efficient, omnidirectional AMP401 microphone has an analog output. It works great for near and long range uses and is particularly suitable for a mobile projects given its extremely low energy consumption. You can use it in a range of applications - we can see it used in smartphones, cameras or electronic nannies. Code SP021
SparkFun Altavoz Hamburger SparkFun Hamburger speaker is a high quality speaker in a small form and with even smaller price. You wouldn't believe you can get a quality product for less than 7€, right? Well, we couldn't believe that as well, but SparkFun makes that possible. Code SP022 ✗ Out-of-Stock Price €7.99
SparkFun Pulse Oximeter and Heart Rate Sensor - MAX30101 & MAX32664 (Qwiic) This tiny little board features two chips from Maxim Integrated: MAX32664 and MAX30101. The 30101 Oximetry module is the sensor on board responding for both oximetry and heart rate sesnsing. The MAX32664 is equipped with a Cortex M4 handling algorithimc calculations, digital filtering and automatic gain control. The board comes with I2C and SparkFun has provided to it Qwiic connectors for ease of use. Code SP030 Last items in stock Price €52.99
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
SparkFun GPS Breakout This small GPS breakout is yet another Qwiic module from SparkFun as per usual based on I2C - meaning that you can keep your serial port free for other applications. The board features XA1110 GPS module from GTOP and MediaTek MT3333 chipset already loaded with SparkFun firmware enabling clean and easy use of both ports. Code SP034 Last items in stock Price €65.99
Serial Enabled 16x2 LCD - White on Black 5V It is the freshest serial LCD from SparkFun. Similarly to other SparkFun LCD screens it is put on single board with a microcontroller, however in contrast to the other screens in our offer (SP027 and SP028) it is based on PIC16F88 rather than ATmega328. Code SP035 Last items in stock Regular price €36.99 -€10.00 Price €26.99
Bus Pirate - v3.6a This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board. This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin. Code SP037 Last items in stock Price €39.99
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Last items in stock Price €34.99
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP039 Last items in stock Price €33.99
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €6.49
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €3.29
MyoWare Muscle Sensor Development Kit - OBSOLETE This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered electromyography (EMG) sensor kit that gives you the MyoWare, each MyoWare Shield and everything you need to connect them all together. Code SP074
MyoWare Power Shield MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V. Code SP071 Backorder Price €6.49
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €8.99
SparkFun RedBot Sensor - Accelerometer The accelerometer sensor is an add-on for your RedBot that provides shock and motion detection. The sensor works by measuring acceleration forces on the x, y and z axes. By measuring the amount of acceleration (or lack thereof), your robot can better understand its movements. Code SP078 Available Price €8.99
MyoWare 2.0 Cable Shield This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person. Code SP045 Available Price €7.49
Load Cell Weight Sensor 50kg Pressure sensor sometimes called strain gauge. Load cell for measuring weights up to 50kg. The transducer measures the strain of the metal structure and converts it into a few mV. Code Sp096 Available Regular price €7.69 -€0.99 Price €6.70