Printed Circuit Board Terminal 3 poles 5.08mm pitch Blue 2 pole PCB mount screw terminal 5.08mm pitch Printed Circuit Board Terminal 3 poles 5.08mm pitch features: Number of Contacts: 3 Pitch: 5.08mm Number of Rows: 1 Mounting Type: PCB Gender: Male Allowable Section: 1.5mm2 (22- 14 AWG) Termination method: screw Type: screw terminal block Nominal current: 16A Nominal voltage: 250V Color: blue Material: Nylon 66 Depth: 10mm Width: 7.5mm Length: 10mm Code K0218 Available Price €0.28
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.61
DS18B20 Submersible Probe Sensor Temperature Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.DS18B20 Submersible Probe Sensor Temperature features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Red Vcc - Yellow digital output- Inocidable steel- Cable length: 1m Code S0019 ✗ Out-of-Stock Price €1.98
1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino 1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 5V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL001 Available Price €1.98
10x Linear Potentiometers 1k OHM kΩ 10x Linear Potentiometers 1k OHM kΩ features:- Horizontal variable resistance PCB- 1k Ohm kΩ Linear- Quantity: 10 units Code K0183 Available Price €0.10
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Available Price €2.44
10x Strip 8 Pin Female Short 10x Strip 8 Pin Female Short features: - Pin spacing: 2.54mm - Insert position: Vertical - Insert: Through - Quantity: 10 units of strips of 8 female pins each Code K0142 Available Price €0.16
Resistor 1K Ohm 5% 0,25W 1/4W Resistor 1K Ohm 5% 0,25W 1/4W features:-1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0013 Available Price €0.07
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Last items in stock Price €4.45
Lilypad LED Red LED of red color.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Red features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: red- Size: 5.5x12.5 mm- 1 LED included Code M0138 Last items in stock Price €0.82
NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features: - Standard: NFC Forum Type2 Tag Ntag215 - Protocol: ISO14443A - Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ - Reading distance: 0-10CM - Communication speed: 106Kboud - Working temperature: -20ºC to 70ºC - Number of uses 100,000 times - Data retention: 10 years - Material: PVC - Dimensions 86 x 54 x 0.84 mm Code M0052 Available Price €1.64
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.61
Lilypad Slide Switch Board 2 Positions Interruptor This is a simple slide switch for LilyPad. Use it as a simple On / Off switch, or to control LEDs, buzzers, sensors, etc.The switches in each panel have a capacity of 4V to 300 mA, but will operate at 5V with a current reduction.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Slide Switch Board 2 Positions Interruptor features: - Switch two positions: On (ON) / Off (OFF)- Density of the PCB: 0.8 mm- Size: 7.75x18.1 mm Code M0141 Available Regular price €1.64 -€0.50 Price €1.14
SONOFF AL010 RJ9 Adaptor SONOFF AL010 RJ9 Adapter dedicated to sensors compatible with the previous Sonoff TH16 series, where there was a Mini Jack connector. Suitable for temperature and humidity sensor AM2301 and Si7021, waterproof temperature sensor DS18B20 and soil moisture sensor MS01. Code WS075 Available Price €2.31
PAM8610 2X10W Dual Channel Amplifier The amplifier with high efficiency, in case of 12 V power supply can output 10 W + 10 W power. Code M0209 Available Price €2.93
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €7.85
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.12
LED Module Full Color RGB Bulb KY-016 This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately. The LED Bulb Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins. These are capable of shining in a wide range of colors thanks to the mixture of the three colors. primary (red, green and blue). These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package. Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors. Code M0081 Available Price €2.44
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Last items in stock Price €4.45
Lilypad LED Red LED of red color.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Red features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: red- Size: 5.5x12.5 mm- 1 LED included Code M0138 Last items in stock Price €0.82
NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features: - Standard: NFC Forum Type2 Tag Ntag215 - Protocol: ISO14443A - Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ - Reading distance: 0-10CM - Communication speed: 106Kboud - Working temperature: -20ºC to 70ºC - Number of uses 100,000 times - Data retention: 10 years - Material: PVC - Dimensions 86 x 54 x 0.84 mm Code M0052 Available Price €1.64
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.61
Lilypad Slide Switch Board 2 Positions Interruptor This is a simple slide switch for LilyPad. Use it as a simple On / Off switch, or to control LEDs, buzzers, sensors, etc.The switches in each panel have a capacity of 4V to 300 mA, but will operate at 5V with a current reduction.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Slide Switch Board 2 Positions Interruptor features: - Switch two positions: On (ON) / Off (OFF)- Density of the PCB: 0.8 mm- Size: 7.75x18.1 mm Code M0141 Available Regular price €1.64 -€0.50 Price €1.14
SONOFF AL010 RJ9 Adaptor SONOFF AL010 RJ9 Adapter dedicated to sensors compatible with the previous Sonoff TH16 series, where there was a Mini Jack connector. Suitable for temperature and humidity sensor AM2301 and Si7021, waterproof temperature sensor DS18B20 and soil moisture sensor MS01. Code WS075 Available Price €2.31
PAM8610 2X10W Dual Channel Amplifier The amplifier with high efficiency, in case of 12 V power supply can output 10 W + 10 W power. Code M0209 Available Price €2.93
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €7.85
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.12
LED Module Full Color RGB Bulb KY-016 This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately. The LED Bulb Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins. These are capable of shining in a wide range of colors thanks to the mixture of the three colors. primary (red, green and blue). These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package. Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors. Code M0081 Available Price €2.44