3D Printers

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers

Characteristic:
- Motor passes 1.8º (200 steps per turn)
- Capable of loading 1.22 kg / cm

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers.

RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825.

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825.

It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 4.28 kg/cm. It comes with a 1m cable. We have the best stepper motors at the best prices! 

Auto shut down module for MKS GEN L SKR V1.3 

MKS PWC automatically turning off after the printing. It helps in the cases like the unexpected power off or you have to leave during the printing, and other similar issues. 

MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply.

One of the most popular stepper motors with 200 steps per revolution and a maximum load of 5 kg/cm. It comes with a 30 cm cable. We have the best stepper motors at the best prices!

One of the most popular stepper motors with 200 steps per revolution and a maximum load of 12.8 kg/cm. It comes with a 30 cm cable. We have the best stepper motors at the best prices!

Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features:
- Superior performance of MOSFET
- Maximum current - up to 30A (heat sink)
- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series
- To control - 5-24V digital signal

It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 19.3 kg/cm. It comes with a 30 cm cable. We have the best stepper motors at the best prices!

TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink

Compared to the TMC2100 module, the TMC2208 controller module emits less heat.

It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations.
Characteristic:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 45 V
- Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32
- Factory soldered temples
- 4-layer PCB, 2 oz. Copper for improved heat dissipation
- Short-circuit and overtemperature protection - Use potentiometer to adjust the current
- Measurements: 20x16x12 mm

It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 28.5 kg/cm. Comes with a 50 cm cable. We have the best stepper motors at the best prices! Perfect for CNC machines!

Mounting Bracket for Nema Engine 17 42mm features:
- Steel bracket for PAP Nema 17 3D printer motor
- Mounting bracket of 42mm L shape alloy steel for The NEMA17 3D Stepper Motor Printer
- Material: Alloy Steel - Size: 5 x 5 x 5cm
- Black Color
- Fit for 42mm Stepper Motor as NEMA17

A4988 + RepRap Radiator features:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

67mm L shape alloy steel mounting bracket for NEMA23 3D stepper motor printer Mounting Bracket for Nema Motor 23 57mm/76mm features:
- Compatible with Nema 23 body length: 57mm and 76mm
- Material: alloy steel
- Size: 67 x 67 x 2,7 mm
- Black color
- Fit for stepper motor as NEMA23

Stepstick A4988 controller
Driver for stepper motors
Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield
A4988 + Stepstick Radiator Stepper Motor Reprap features:

- Minimum operating voltage: 8 V
- Operating voltage maximum: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

Dupont female-female connector cable to PH2.00 for Nema engine features:
Dupont 2.54 female to PH2.00 female connecting cable for Nema motor Length 100cm

Router TB6560 1 Axis 3A Stepper Motor Driver Board features:
- Minimum operating voltage: 10 V
- Maximum operating voltage: 35 V (24V recommended)
- Maximum current: ± 3 A
- Stepper motor · two phases · four phases
- Resolution of microsteps: full, 1/2, 1/8, and 1/16
- PCB measurements: 75x50 mm
- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board
- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply
- 6N137 high speed optical coupling guarantees high speed without losing steps
- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent
- Protection circuit to ensure optimal performance
- Maximum nominal output: 3 A, peak 3.5A

Heat Sink Aluminium Nema 17 features:
- MK8 Extruder Radiator Heatsink Printer
- Ideal for NEMA17 motors and MK7 and MK8 extruders - Dimensions 40 x 40x 11mm

5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features:
- Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software.
- Designed for single axis CNC single phase stepper controller controller:
M542, MA860H, 2M542, DM860 etc.
- Stepper motor controller drivers 5 axis maximum support.
- Wide input voltage range: 12-24V and with anti-reverse function.
- USB power supply and peripheral power phase are separated to protect computer security
- All signals are opto-isolated, which can protect the security of your computer.
- 5 input interface to define limit, emergency stop, cutter alignment, etc.
- A relay output control interface, accessed by spindle motor or air pump, water pump, etc.

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 3.5A Stepper Motor Driver Board features:
- Minimum operating voltage: 9 V
- Maximum operating voltage: 40 V
- Maximum current: ± 3.5 A
- Maximum power: 160W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs 5V optically isolated
- Step resolution: 200, 400, 400, 800, 1600, 3200, 6400
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 y 1/32 adjustable by interruptor DIP
- Current control: 0.5A/>0A/>

The output current of this controller is infinitely adjustable to meet the various requirements of your application.
It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.
Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.
Its large heat sink allows good quality cooling.
The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features:
  - Operating voltage DC 10V-45V
- Maximum nominal output: 4.5 A
- DC32V switching power is recommended
- 6N137 high speed optical coupling, ensure high speed without losing step

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 5A Stepper Motor Driver Board features:
- Minimum operating voltage: 12 V
- Maximum operating voltage: 48 V
- Maximum current: ± 5 A
- Maximum power: 240W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs optically isolated
- Step resolution: 200, 400, 1600, 3200
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 adjustable by interruptor DIP
- Current control: 0.2A/0.6A/1.2A/1.8A/2.5A/3.3A/4.2A/>

Mechanical End of Career CNC Ramps1.4 3D Printer features:
- Mechanical limit switch, Endstop
- 100% brand new and high quality
- 1A 125V AC switch - Cable length: 70cm
- PCB dimensions: 40mm x 15mm

Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features:
- 100% brand new and high quality
- Optical detector: TCST2103
- Length cable: 50cm
- Size: 32mm x 10mm

Mechanical Ender 3 5 CR 10 20 X Pro 3D Printer features:
- Mechanical limit switch, Endstop
- 100% brand new and high quality
- 1A 125V AC switch - Compatible with Ender-3 series, CR-10 series, etc.
- PCB dimensions: 18mm x 18mm

Zum Scanner Expansion Board 3D DIY features:
- Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- 3D Scanner Ciclop is an open source project created by bq
- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser
- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board

Feature of 3D Zum shield: - Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- Content:
       - 1x Zum Shield 3D
       - 1x UNO R3 Compatible Arduino
       - 1x Controller A4988
       - 1x Male pin strip
       - 1x Heatsink for A4988
       - 1x USB cable
       - Jumpers

The kit contains the Mega board, the Ramps 1.4 shield and 4 A4988 controllers with heatsinks.

CNC shield for arduino works as a controller for CNC type milling machines,
3D printers, laser cutters .
CNC Shield Expansion Plate V3 Engraver 3D Printer features:

• 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible
• 4 support axes X, Y, Z, A
• 2 limit switches for each axis (6 in total)

A CNC expansion board kit and 4 stepsticks A4988 for 3D printer. See each component in the product description for details.

CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features:
- Content:
* 1x UNO R3 CH340 Compatible with Arduino
* 1x CNC Shield V3
* 4x A4988 Drivers
* 4x Heatsinks for A4988
* Jumpers

Contented:
- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino
- 1x CNC Shield V3
- 4x A4988 Drivers
- 4x Heatsinks for A4988
- USB Cable
- Jumpers

IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A features:
- For Hot Bed Ramps
- Package: TO-220
- Quantity: 1 unit with heatsink and screw

The controller creates step-by-step motor control functions preset with the latest imported high-speed chip and uses a combination of software and hardware methods to ensure superior anti-jam performance of the controller.
It also has reverse polarity protection, overvoltage protection, overcurrent protection, absolute guarantee of safe operation of the controller in a variety of hostile factory environments.
Applies to stepper motor control switches, round-trip motion control, fixed speed control. Industrial DKC-1A stepper motor controller features:
- Operating voltage: 5-32 VDC
- Signal entry point for the lower level entry
- Optimization of the acceleration of the S curve
- The maximum output frequency can reach 20 KHz

The DM556 low-voltage digital stepper motor controller, which uses the latest 32-bit DSP technology, is suitable for driving the 57 and 86 series motors Nema23, with excellent low-speed performance to meet the application needs of small and medium-sized equipment.

It is one of the most popular stepper motors with 200 steps per revolution and a maximum load of 2.6 kg/cm (0.25 Nm). It is supplied with a voltage of 12.0 V, consumes a current of 400 mA per coil. Dimensions: 42 x 42 x 34 mm (NEMA 17).  Comes with a 30 cm cable. We have the best stepper motors at the best prices!