Components and sensors

The sensor measures the current flowing in the cable without cutting it. The measurement is made on a single insulated wire, the output is an analog voltage from 0 to 1 V. Sensor SCT-013-030, Non-Invasive 30A AC Current Meter features:
Input current: 0 to 30A AC Output voltage: 0 to 1 V AC Built-in load resistance: 62 Ω Winding ratio: 1800: 1 Operating temperature range: -25 ° C to 70 ° C Cable length: 1 m Sensor weight: approximately 45 g Sensor SCT013-030 datasheet

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached

This accelometer is powered with 1.8 to 3.6V and consumes only up to 320 uA of current. The circuit fits on the small 18mm on 18mm board and is fully compatible with Arudino

This board features and extremely low power LIS331HH accelerometer. The unit is a MEMS three axis linear accelerometer with a I2C- SPI serial interface enabling use with embedded applications. The range of measurement includes three options +-6g/+-12g/+-24g and enables datalogging with output rates fro 0.5 Hz to 1kHz. Check this and plenty of other accelerometers in our offering of both Sparkfun and other producers

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached

It is a version without headers of a popular BOB-09868 from SparkFun.

In our offer, we have a versuib with headers (SP0001) and with QWIC system (SP0005).

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. It comes with QWIIC connectors

This sensor from Advancer Technologies is an improved version of the bestseller from this producer. It got several upgrades including single supply voltage of 3.1V up to 5V, polarity protection in the power pins output and RAW EMG. 

This a pack of 10 disposable electrodes is for biomedical measuring including EEG. Best suited for monitoring of neuro- and bio-feedback purposes. These are a single use, however very user friendly thanks to the latex-free gel.

This is not a medical device and is to be used for strictly educational purposes.

12VDC plastic solenoid valve. Normally closed. Liquid can flow in one direction and a minimum pressure of 0.02Mpa (3 PSI) is required. This liquid valve would be a great addition to your robotic gardening project. There are two 1/2 ″ outlets. Normally, the valve is closed. When 12VDC is applied to the two terminals, the valve can be opened and pushed.

Mini electricity generator, built base on a turbine and an electric generator that converts kinetic energy into electricity. The generator output is rectified and regulated for a maximum of 12V. Please note -if we want to generate more current, the turbine will oppose the greater resistance to the flow of water, and the voltage may drop if the water flow is not sufficient. This generator is made of plastic and the turbine is totally isolated from the generator and rectifier, the outputs are 1/2 "usually found in domestic pipes.

The INA219 breakout board can be powered by the 5V or 3V pin on your Arduino and communicates via I2C. If you want to sense an Direct Current (DC) with high accuracy and voltage too, we suggest you to use this sensor. I2C sensor can easily interfaced with arduino. It uses 4 pins only.

The new SensorTag IoT kit invites you to realize your product idea connected to the cloud.
The new SensorTag now includes 10 low-power MEMS sensors in a small red package.
And it's expandable with DevPacks to make it easy to add your own sensors or actuators.
Connect to the cloud with low-power Bluetooth and Get your sensor data online in 3 minutes.
The SensorTag is ready to go right away with an iOS and Android app, no programming experience to get started.
The new SensorTag is based on The CC2650 Wireless MCU, which offers 75% less power consumption than previous Bluetooth low energy products.
This allows the SensorTag to run on batteries, and offers years of battery life with a single coin cell battery.

The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

The kit includes 20 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes.

The kit includes 30 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes.

The kit includes 40 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes.

Seeed Grove Arduino Starter kit is a game-changer for schools and robotic classes. You get a set of 10 sensors with a Arduino compatible board and 12 classes for only 28.99 EUR!

The Grove inventor kit is a great extension set for your micro:bit. By using Grove shield for micro:bit you are able to connect all the modules included in the pack purely by the Grove connectors with no need to solder or wire any parts. Now you can focus only on programing with your great mirco:bit.

The Grove Base Kit for Raspberry is all you need to start playing and making with your Raspberry Pi board. It is compatible with boards Pi 3 and Pi 4 and includes 8 basic sensors, a display and a motor. All of that on the grove connectors making it a seamless experience.

With this small module, you can integrate your Raspberry with Amazon Alexa voice module or Google Assistant. It has never before been so easy. Get a chance to experience challenges of the newest technological developments in AI and smart home technologies.

The module is equipped with an electret microphone with a sensitivity in the range of 20-20 kHz and the amplification is used in the Maxim MAX4466 integrated circuit, an operational amplifier specially designed for use as a microphone preamplifier.

The 28 sensor kit is a great extension kit for your micro: bit. Using Sensor shield for micro: bit you can connect all the modules included in the pack only by the connectors without the need to solder or wire any part. Now you can just concentrate on programming with your big mirco: bit.

This fingerprint scanner (as608-optical reader) is ideal for Arduino or Raspberry thanks to its small size and low power consumption. It has a simple interface, high reliability, good adaptability of wet and dry fingers, fast recognition speed and also in fast fingerprint search. Storage capacity of up to 120 fingerprints in its internal FLASH memory.

Level sensor for liquids with float. The liquid level sensor acts as a switch. Liquid level float sensors are used when constant control and regulation of the liquid level (water, oil and other fluids) is required such as extraction pumps. The sensor is equipped with a float with a magnet which, acting by the buoyancy force of the fluid, moves along the tube, shortening or opening the reed switch.

It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where the level of non-corrosive liquids such as water tanks or aquariums needs to be monitored. It is made of stainless steel.

This sensor behaves like a switch that closes the circuit when both parts are put together. Ideal for intrusion detection, alarm system, light control and opening and closing devices. 

The GY-906 BAA is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, within 3 cm the precision is higher, approximately 0.5 degrees

The GY-906 BCC is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, accuracy within 5 cm is approximately 0.5 degrees higher

With this small and simple device, you can control your blood oxygen level yourself to avoid going to the doctor or pharmacy on purpose. Simply insert your finger and wait for the reading of haemoglobin (Spo2), heart rate and Perfusion Index (PI%). The heart rate is also graphically displayed. 

You can rotate the screen to see it in its 4 positions. High precision device, with low power consumption and automatic shutdown. 

This detection module that allows you to detect your heart rate and blood oxygen level from your Arduino project. You can monitor your blood oxygen level yourself to avoid going to the doctor or pharmacy on purpose. Simply press the sensor with your finger and wait for the reading of hemoglobin (Spo2), heart rate and Perfusion Index (PI%). It is a solution as an integrated heart rate sensor and pulse oximetry, which includes two LEDs, a photodetector and is optimized for analog low noise optics.

Velostat or Linqstat film of pressure sensitive material ideal for DIY projects on Arduino, Raspberry or other platforms. When folded or creased it reduces its resistance allowing for flexible sensors.

SONOFF SNZB-02 is an elegant mini wireless intelligent temperature and humidity sensor via ZigBee, through its Bridge(required). Program and create scenes based on the detected values. Maintain a stable temperature in your home.

This HAT is an open source portable sensor that provides the level of suspended particulate matter quantity with its mass. It has a powerful and high-tech PMSA003 sensor that provides the information of suspended particulate matter (PM1.0, PM2.5, PM10) in the air per unit volume.

This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person.

Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid.

This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered electromyography (EMG) sensor kit that gives you the MyoWare, each MyoWare Shield and everything you need to connect them all together.

MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V.

This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads.

The accelerometer sensor is an add-on for your RedBot that provides shock and motion detection. The sensor works by measuring acceleration forces on the x, y and z axes. By measuring the amount of acceleration (or lack thereof), your robot can better understand its movements.

The SparkFun micro:Climate kit is a complete weather station kit that builds on the weather:bit carrier board with weather and soil moisture sensors, all powered by the micro:bit. board.

Using Grove shield for micro:bit you can connect all modules included in the pack only by Grove connectors without soldering or wiring any parts. Now you can concentrate only on programming with your great micro:bit.

ZigBee temperature and humidity sensor provides accurate temperature and humidity measurements and stores this data in memory for one year. Broken down into days with hours, months and a year.

The local Zigbee gateway for your Tuya Zigbee devices provides high-speed local Ethernet + Zigbee Mesh connectivity, increased automation possibilities, local memory for parameters and devices.

ZigBee temperature and humidity sensor provides accurate temperature and humidity measurements and stores this data in memory for one year. Broken down into days with hours, months and a year.

This ZigBee open-close sensor provides information about the opening and closing status of the sensor, saving this data in memory. Ideal for knowing the status of doors and windows in intruder detection systems

The UNI-T UT300H temperature meter, which uses the latest technology, enables temperature measurements in the range of 32°C-42.9°C. The high accuracy of the device enables fast and accurate monitoring of body temperature as well as other environmental elements, e.g. objects, food, liquids, etc.

The UNI-T UT300H temperature meter, which uses the latest technology, enables temperature measurements in the range of 32°C-42.9°C. The high accuracy of the device enables fast and accurate monitoring of body temperature as well as other environmental elements, e.g. objects, food, liquids, etc.

Level sensor for liquids with float. The liquid level sensor acts as a switch. Liquid level float sensors are used when constant control and regulation of the liquid level (water, oil and other fluids) is required such as extraction pumps. The sensor is equipped with a float with a magnet which, acting by the buoyancy force of the fluid, moves along the tube, shortening or opening the reed switch.

It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where the level of non-corrosive liquids such as water tanks or aquariums needs to be monitored. It is made of stainless steel.

Level sensor for liquids with float. The liquid level sensor acts as a switch. Liquid level float sensors are used when constant control and regulation of the liquid level (water, oil and other fluids) is required such as extraction pumps. The sensor is equipped with a float with a magnet which, acting by the buoyancy force of the fluid, moves along the tube, shortening or opening the reed switch.

It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where the level of non-corrosive liquids such as water tanks or aquariums needs to be monitored. It is made of stainless steel.

Level sensor for liquids with float. The liquid level sensor acts as a switch. Liquid level float sensors are used when constant control and regulation of the liquid level (water, oil and other fluids) is required such as extraction pumps. The sensor is equipped with a float with a magnet which, acting by the buoyancy force of the fluid, moves along the tube, shortening or opening the reed switch.

It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where the level of non-corrosive liquids such as water tanks or aquariums needs to be monitored. It is made of stainless steel.

Stylish smart scale with tempered glass platform with heart rate measurement and 12 body analysis functions. Compatible with the Tuya Smart App (iOS 8.0 or higher, Android 6.0 or higher). Easy-to-read LED display.

This air purifier uses a HEPA filter to safely remove viruses, bacteria, mold, mildew, dander, etc. Filters up to 99.5% of dust, pollen, tobacco smoke, mould spores and pet dander. Keeps the environment clean.

This air purifier uses a HEPA filter to remove viruses, bacteria, mould, dander, etc. safely. The dehumidifier regulates humidity in the bathroom, kitchen, etc. Filters up to 99.5% of dust, pollen, tobacco smoke, mould spores and pet dander. Keeps the environment clean.

Capsule Electret Condenser Microphone 9.5mm

This sensor behaves like a switch that closes the circuit when both parts are put together. Ideal for intrusion detection, alarm system, light control and opening and closing devices. 

Led IR 3mm is a pair of infrared LED's consisting of a photodiode (Emitter) that emits an infrared light when polarised through its working voltage ranges and a phototransistor (Receiver) that allows to capture the infrared light emitted by the photodiode.

Keyes 37 sensor kit is a great extension set for your Micro:Bit. Using Sensor shield for Micro:Bit you can connect all modules included in the pack only by the connectors without soldering or wiring any parts. Now you can concentrate only on programming with your big Mirco:Bit.