LDR Module Motor Resistance KY-018 This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases. On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND 2- VCC 3- analog output - the voltage depending on the light - Supply voltage: 3.3 V-5VDC - PCB size: 19x15x8 mm Code S0122 Available Price €1.15
Battery holder 2x AA Battery holder with switch Includes a switch to output the voltage built into the case itself. It has a cover to protect the batteries. The cover has perforation in case you want to secure it with a screw (not included). Battery holder 2x AA Battery holder with switch features: - Cable 15cm long - Measurements 68x 32x 18mm - Battery length max 50mm - Compatible batteries (LR06, R06, MN1500, AM3, UM3 , HP7) Code PP005 Available Price €1.15
XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.02
Potentiometer B10K linear Characteristic: -10k OHM kΩ - linear potentiometer 10k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0067 Available Price €0.82
Adapter Battery 9V 6F22 Jack Connector DC Ideal to power your Arduino board through the power input.Adapter Battery 9V 6F22 Jack Connector DC features:- Cable 7cm long- Battery connector 9V, 6F22- Male connector DC 5.5 / 2.5 Code PP011 Available Price €0.62
DHT11 Module Temperature and Humidity Sensor The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables Code S0001 Available Price €2.47
Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.Your converter has four analog inputs, one analog output and one I2C serial bus interface.It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features: - Supply voltage (between VSS and VDD): 2.5-6VDC Code M0133 Available Price €2.39
LED Diode Assortment Kit 40x Red Green Yellow Blue LED Diode Assortment Kit 40x Red Green Yellow Blue features: - Lens color: Red, green, yellow, blue -difused- Size: 5 mm- Operating current: 20mA- Voltage (red) 1.8V-2.3V- Voltage (green) 3.2V-3.4V- Voltage (yellow) 1.8V-2.3V- Voltage (blue) 3.2V-3.4V- Anode (A): Positive (long leg): 28mm- Cathode (K): Negative (shorter leg): 25 mm- Operating temperature: -25ºC/80ºC- Welding temperature: + 260ºC- Quantity: 40 units - 10x red - 10x green - 10x yellow - 10x blue Code P0012 Available Price €0.05
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (wo headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached It is a version without headers of a popular BOB-09868 from SparkFun. In our offer, we have a versuib with headers (SP0001) and with QWIC system (SP0005). Code SP004 Last items in stock Price €14.04
MMA7361 Triple Axis Analog Accelerometr 3-axis analog accelerometer module based on the MMA7361 sensor. The built-in sensor has a low demand for electricity. The measuring range of the sensor can be changed between two ranges ± 1.5 g and ± 6 g. The selection is made using a digital input or welded bridges. MMA7361 Triple Axis Analog Accelerometr features: MMA7361 3-axis analog accelerometer Supply voltage: 3.3 - 5 V (built-in RT9161 chip) Measuring range selected from the IO line of the microcontroller or via bridges Comparators with hysteresis for CMOS / TTL 3.3 V, 5 V inputs Pin pitch: 2.54 mm Dimensions: 28 x 17 mm. Helpful links - MMA7361 datasheet Code M0175 Available Price €10.70
MPU-6050 Accelerometer Module + Gyroscope 3 Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:- Chip: MPU-6050- Power supply: 3V-5V- Operating current: 5mA- Communication: I2C- 16-bit analog-digital converter on all axes- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)- Dimensions: 14 x 21 x 1.3mm- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin) Code M0017 ✗ Out-of-Stock Price €3.55
Low power Bluetooth / Multi-standard SensorTag CC2650STK TI The new SensorTag IoT kit invites you to realize your product idea connected to the cloud. The new SensorTag now includes 10 low-power MEMS sensors in a small red package. And it's expandable with DevPacks to make it easy to add your own sensors or actuators. Connect to the cloud with low-power Bluetooth and Get your sensor data online in 3 minutes. The SensorTag is ready to go right away with an iOS and Android app, no programming experience to get started. The new SensorTag is based on The CC2650 Wireless MCU, which offers 75% less power consumption than previous Bluetooth low energy products. This allows the SensorTag to run on batteries, and offers years of battery life with a single coin cell battery. Code W0088 Backorder Price €37.19
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (Qwiic) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. It comes with QWIIC connectors Code SP005 Backorder Price €12.39
ADXL345 3-Axis Accelerometer SPI and I2C Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It serves to measure the static acceleration, for example gravity, in applications where you need to measure the inclination.Also to measure dynamic acceleration, movement. ADXL345 3-Axis Accelerometer SPI and I2C features: - Type: 3-axis accelerometer- Chip: ADXL345- Supply voltage: 3-5V- Consumption: 40uA active and 0.1uA on hold- Communication: SPI and I2C- Measurements: Static and dynamic acceleration- Accelerometer scales ± 2g, ± 4g, ± 8g and ± 16g- Resolution: 13 bits- Dimensions: 20x16mm- Operating temperature: -40 °C to +80 °C- Detection: Free fall, click-double click Code M0018 Available Price €2.55
SparkFun Triple Axis Accelerometer Breakout - LIS331 This board features and extremely low power LIS331HH accelerometer. The unit is a MEMS three axis linear accelerometer with a I2C- SPI serial interface enabling use with embedded applications. The range of measurement includes three options +-6g/+-12g/+-24g and enables datalogging with output rates fro 0.5 Hz to 1kHz. Check this and plenty of other accelerometers in our offering of both Sparkfun and other producers Code SP003 Available Price €15.66
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (with Headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached Code SP001 Last items in stock Price €14.04
SparkFun RedBot Sensor - Accelerometer The accelerometer sensor is an add-on for your RedBot that provides shock and motion detection. The sensor works by measuring acceleration forces on the x, y and z axes. By measuring the amount of acceleration (or lack thereof), your robot can better understand its movements. Code SP078 Available Price €7.43
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (wo headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached It is a version without headers of a popular BOB-09868 from SparkFun. In our offer, we have a versuib with headers (SP0001) and with QWIC system (SP0005). Code SP004 Last items in stock Price €14.04
MMA7361 Triple Axis Analog Accelerometr 3-axis analog accelerometer module based on the MMA7361 sensor. The built-in sensor has a low demand for electricity. The measuring range of the sensor can be changed between two ranges ± 1.5 g and ± 6 g. The selection is made using a digital input or welded bridges. MMA7361 Triple Axis Analog Accelerometr features: MMA7361 3-axis analog accelerometer Supply voltage: 3.3 - 5 V (built-in RT9161 chip) Measuring range selected from the IO line of the microcontroller or via bridges Comparators with hysteresis for CMOS / TTL 3.3 V, 5 V inputs Pin pitch: 2.54 mm Dimensions: 28 x 17 mm. Helpful links - MMA7361 datasheet Code M0175 Available Price €10.70
MPU-6050 Accelerometer Module + Gyroscope 3 Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:- Chip: MPU-6050- Power supply: 3V-5V- Operating current: 5mA- Communication: I2C- 16-bit analog-digital converter on all axes- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)- Dimensions: 14 x 21 x 1.3mm- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin) Code M0017 ✗ Out-of-Stock Price €3.55
Low power Bluetooth / Multi-standard SensorTag CC2650STK TI The new SensorTag IoT kit invites you to realize your product idea connected to the cloud. The new SensorTag now includes 10 low-power MEMS sensors in a small red package. And it's expandable with DevPacks to make it easy to add your own sensors or actuators. Connect to the cloud with low-power Bluetooth and Get your sensor data online in 3 minutes. The SensorTag is ready to go right away with an iOS and Android app, no programming experience to get started. The new SensorTag is based on The CC2650 Wireless MCU, which offers 75% less power consumption than previous Bluetooth low energy products. This allows the SensorTag to run on batteries, and offers years of battery life with a single coin cell battery. Code W0088 Backorder Price €37.19
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (Qwiic) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. It comes with QWIIC connectors Code SP005 Backorder Price €12.39
ADXL345 3-Axis Accelerometer SPI and I2C Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It serves to measure the static acceleration, for example gravity, in applications where you need to measure the inclination.Also to measure dynamic acceleration, movement. ADXL345 3-Axis Accelerometer SPI and I2C features: - Type: 3-axis accelerometer- Chip: ADXL345- Supply voltage: 3-5V- Consumption: 40uA active and 0.1uA on hold- Communication: SPI and I2C- Measurements: Static and dynamic acceleration- Accelerometer scales ± 2g, ± 4g, ± 8g and ± 16g- Resolution: 13 bits- Dimensions: 20x16mm- Operating temperature: -40 °C to +80 °C- Detection: Free fall, click-double click Code M0018 Available Price €2.55
SparkFun Triple Axis Accelerometer Breakout - LIS331 This board features and extremely low power LIS331HH accelerometer. The unit is a MEMS three axis linear accelerometer with a I2C- SPI serial interface enabling use with embedded applications. The range of measurement includes three options +-6g/+-12g/+-24g and enables datalogging with output rates fro 0.5 Hz to 1kHz. Check this and plenty of other accelerometers in our offering of both Sparkfun and other producers Code SP003 Available Price €15.66
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (with Headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached Code SP001 Last items in stock Price €14.04
SparkFun RedBot Sensor - Accelerometer The accelerometer sensor is an add-on for your RedBot that provides shock and motion detection. The sensor works by measuring acceleration forces on the x, y and z axes. By measuring the amount of acceleration (or lack thereof), your robot can better understand its movements. Code SP078 Available Price €7.43