Kit Seeed Grove 20 sensors for Arduino

This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person.

Encapsulated with water resistant stainless steel with sensor dimensions 5.5*50mm, cable length 200 cm. DS18B20 Probe 2m Submersible Temperature Sensor features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Vcc red
      - Yellow digital output
- Inocidable steel
- Cable length: 2m  

The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

Level sensor for liquids with float. The liquid level sensor acts as a switch. Liquid level float sensors are used when constant control and regulation of the liquid level (water, oil and other fluids) is required such as extraction pumps. The sensor is equipped with a float with a magnet which, acting by the buoyancy force of the fluid, moves along the tube, shortening or opening the reed switch.

It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where the level of non-corrosive liquids such as water tanks or aquariums needs to be monitored. It is made of stainless steel.

Ultrasonic sensors overcome many of the weaknesses of IR sensors by providing distance measurement regardless of the color and illumination of obstacles. Ultrasound Distance Sensor HC-SR05 features:
- Power supply: 4.5-5.5 VDC
- Supply current: 10 to 40 mA
- Activation pin format: 10 μs digital pulse
- Echo Pin Output: 0-Vcc
- Echo Pin Format: the output is DIGITAL and directly proportional with range. See our conversion formula below
- Measurement range: 2cm to ~ 4.5m
- Measurement resolution: 0.3cm
- Measurement angle: up to 15 degrees
- Measurement speed: 40 Hz,
- Connector: standard 5-pin male connector that can be connected directly to boards or breadboards:
- 1: VCC
- 2: Trig
- 3: Echo

Holder for ultrasonic, distance meter HC-SR04. Ideal for installing the sensor on mobile platforms such as robots, vehicles, etc.

The module is based on a touch sensitive IC capacitive touch switch module (TTP223B).
In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features:
- Low power consumption
- Input voltage: 2 - 5.5VDC
- Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation
- 3-pin control interface:
1- GND
2- VCC
3- Control signal (output pin)
- Power indicators: Bright green LED when the sensor is on

Led module infrared sensor for Arduino
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm module features:
- 4 Pins Output:
    - A0: analog output
    - D0: digital output
    - GND: ground connection
    - VCC: 5V module power
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.

Seeed Grove Arduino Starter kit is a game-changer for schools and robotic classes. You get a set of 10 sensors with a Arduino compatible board and 12 classes for only 28.99 EUR!

ZigBee temperature and humidity sensor provides accurate temperature and humidity measurements and stores this data in memory for one year. Broken down into days with hours, months and a year.