SparkFun Biomedical sensor pad set 10pcs

Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:
- Chip: MPU-6050
- Power supply: 3V-5V
- Operating current: 5mA
- Communication: I2C
- 16-bit analog-digital converter on all axes
- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)
- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)
- Dimensions: 14 x 21 x 1.3mm
- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin)

Speed controller for DC motor (PWM) 6V-28VDC 3A PWM 6V 12V 24V features:
- Ideal to control the speed of DC motors
- Input voltage: 6-28VDC
- Max continuous output current: 3A
- Max power: 100W
- Dimensions: 50x17x28mm
- PWM frequency: 21kHz
- Adjustable duty cycle: 5% -100%
- Keep in mind that the voltage applied to the motor will be the supply voltage applied to the circuit

The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot.

Ideal to control the speed of DC motors. Speed controller for DC motor (PWM) 10V-30VDC 3A 120W features:
- Input voltage: 10-30VAC
- Max output DC current: 3A (max 4A)
- Max power: 120W (in case input voltage> 24V)
- Dimensions: 74x47x28mm
- PWM frequency: 500kHz
- Duty Cycle adjustable: 5% -95%
Please note that the voltage applied to the motor will be the supply voltage applied to the circuit

Resistor 10K Ohm 5% 0,25W 1/4W features:
-10K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.

Load cell Load Cell 20kg features:
- Load range: 20kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S /°C
- Effect of temperature on zero: 0.05% F.S /°C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65
- Cable length: 25 cm
- Size: 75 x 12.7 x 12.7 mm
- Wiring:
* Red: Feeding +
* Black: Source -
* Green: Sign +
* White: Signal -

Double Cable 26AWG Red Black Flexible PVC - 0,13mm² Prototype features:
- Ideal for your electronic projects.
- Length: 1m
- Conductor: flexible copper
- Insulation: PVC
- Low voltage electric cables
- Cable type: 26AWG
- Resistance to 20ºC: 133.9 Ohm / Km
- Diameter: 0.40mm