Power Supply Transformer 220V AC/DC 1A 5V Power Supply Transformer 220V AC/DC 1A 5V features:- Input voltage: 100~240V 50Hz- Output voltage: DC 5V- Output current: 1A- DC connector: 5.5 mm x 2.1 mm- Cable length: Approx. 90 cm- Indicator of operation: LED diode Code A0069 Available Price €3.30
Sensor Shield V5 APC220 Arduino compatible Arduino Sensor Shield V5 APC220 features: Sensor Shield V5.0 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more Code M0001 Available Price €2.39
DRV8833 Controller DC Motor PAP Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ). The motors are controlled, independently by means of PWM signals the direction of rotation of the motors can be controlled, neutral or stop with a frequency of up to 100 kHz. Two input signals (IN1 and IN2) can be used to control one motor (connected to OUT1 and OUT2) and the other two input signals (IN3 and IN4) to control the second motor (connected to OUT3 and OUT4). NOTE: This DRV8833 dual-bridge motor controller is the replacement for the TB6612FNG dual-channel motor controller. The pins come unsoldered. If the motor draws currents above 0.6A, the use of a heat sink may be required. DRV8833 Controller DC Motor PAP features: Code R0082 ✗ Out-of-Stock Price €2.02
Barometric Pressure, Temperature and Altitude Sensor BMP180 Barometric Pressure, Temperature and Altitude Sensor BMP180 features: - Module based on the atmospheric pressure sensor BMP180- Supply voltage: 1.8 - 3.6 V- Energy consumption: 0.5uA- I2C interface- Measuring range: 300 - 1100hPa- Dimensions: 10 x 13 mm- Includes soldering pins Code M0024 Available Regular price €3.21 -€0.59 Price €2.62
Hall Effect Sensor Module KY-003 with SH3144E TO-92 This module adapted for the arduino is a unipolar Ic Hall effect magnetic sensor. The Hall effect is when a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicular to the direction of current flow, a voltage, called Hall voltage, proportional to the magnetic field, and the current appears on the faces sides of the bar. This tension is proportional to the displacement speed of the charge carriers, which is considerably higher in semiconductor materials than in metal conductors. Hall Effect Sensor Module KY-003 with SH3144E TO-92 features: - 3-pin connector: 1- GND 2- VCC 3- Voltage is recovered depending on the magnetic effect - Supply voltage: 5VDC - Output current: 40mA Code M0131 Available Price €1.40
Motor Nema 17 1.22kg 17HS2408 Characteristic: - Motor passes 1.8º (200 steps per turn) - Capable of loading 1.22 kg / cm Code I0065 Available Price €7.43
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Available Price €4.92
Soldering Iron 40W Soldering Iron 40W features: - Power: 40W- Power: 230V- Equipped with tip B1- Long length tip: 1mm- Anti-thermal handle- CE, RoHS and TUV certifications Code H0190 Available Regular price €9.05 -€2.00 Price €7.05
MH-Z1311A low-power consumption NDIR CO2 sensor Low power CO2 sensor MH-Z1311A, the current consumption is only 150-200uA, waterproof and anti-corrosion, high sensitivity, additionally characterised by excellent linear output. It is very popular used for battery monitors and IAQ devices. Code S0158 Available Price €24.37
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €5.36
DHT22/AM2302 Temperature Humidity Sensor The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree. DHT22/AM2302 Temperature Humidity Sensor features: - Voltage Operating: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Code S0018 Available Price €3.26
Speed sensor module for Arduino motors Speed sensor module for Arduino motors features: - Slot-type optocoupler sensor, slot width: 10 mm. - The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it. - Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high - Power supply: 3.3-5V - Current consumption 15 mA max. - PCB dimensions: 25 x 20 mm Code S0129 Available Price €1.55
10x Photoresistor GL5539 LDR 50k - 100k Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:- Model: GL5539- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 50-100KΩ- Resistance with darkness (0lux): 5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0013 Available Price €0.12
2x CNY70 Reflective Optical Sensor with Transistor Output 2x CNY70 Reflective Optical Sensor with Transistor Output features: - Reflective optical sensor with transistor output- Reflective optical coupler used to distinguish edge or line detection- Dimensions of the housing are 7 x 7 x 6 mm- Supply voltage: 5V- Maximum diode current: 50 mA- Maximum collector-emitter voltage: 32V- Maximum collector current of 50 mA- Quantity: 2 units Code S0121 Available Price €0.62
Gravity: IO Expansion Shield for Arduino V7.1 Gravity: IO Expansion Shield for Arduino V7.1 is a shield board for Arduino that expands the capabilities of the I/O pins. Among other things, it has each pin with a power pair, the ability to include a 3.3 V voltage converter, a separate connector for I2C interfaces, SPI and a socket for XBee modules. Code DF027 Available Price €12.36
MQ-9 Carbon Monoxide Sensor Module MQ-9 Carbon Monoxide Sensor Module features:- Main chip: MQ-9 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 20ppm- 2000ppm carbon monoxide 500ppm- 10000ppm methane CH4 500ppm- 10000ppm LPG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0033 Available Price €2.39
Dallas Temperature Sensor Module DS18B20 The DS18B20 is a digital temperature sensor from Dallas Semi Conductors, used to measure ambient temperature or to carry out tests. It supports multipoint readings of the mesh networking type, being able to be deployed in three lines, in order to achieve these readings, it has a built-in pull-up resistance. Dallas Temperature Sensor Module DS18B20 features: - Operating voltage: 3 - 5.5 VDC - Measurement operating temperature: -55 ° C - 125 ° C - Output current: 5 μA - Accuracy of ± 0.5 ° C between -10 ° C and + 85 ° C - Storage temperature: -55 ° C - + 125 ° C - 100% new and high quality - Module DS18B20 temperature measurement sensor - The DS18B20 sensor has a pull-up resistor - Power indicator LED on the module Code S0124 Available Price €1.61
MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features: - Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Concentration detection: 200ppm - 5000ppm LPG, propane 300ppm - 5000ppm butane 5000ppm - 20000ppm methane 300ppm - 5000ppm H2 100ppm -2000ppm alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0027 Available Price €2.39
MH-Z1311A low-power consumption NDIR CO2 sensor Low power CO2 sensor MH-Z1311A, the current consumption is only 150-200uA, waterproof and anti-corrosion, high sensitivity, additionally characterised by excellent linear output. It is very popular used for battery monitors and IAQ devices. Code S0158 Available Price €24.37
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €5.36
DHT22/AM2302 Temperature Humidity Sensor The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree. DHT22/AM2302 Temperature Humidity Sensor features: - Voltage Operating: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Code S0018 Available Price €3.26
Speed sensor module for Arduino motors Speed sensor module for Arduino motors features: - Slot-type optocoupler sensor, slot width: 10 mm. - The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it. - Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high - Power supply: 3.3-5V - Current consumption 15 mA max. - PCB dimensions: 25 x 20 mm Code S0129 Available Price €1.55
10x Photoresistor GL5539 LDR 50k - 100k Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:- Model: GL5539- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 50-100KΩ- Resistance with darkness (0lux): 5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0013 Available Price €0.12
2x CNY70 Reflective Optical Sensor with Transistor Output 2x CNY70 Reflective Optical Sensor with Transistor Output features: - Reflective optical sensor with transistor output- Reflective optical coupler used to distinguish edge or line detection- Dimensions of the housing are 7 x 7 x 6 mm- Supply voltage: 5V- Maximum diode current: 50 mA- Maximum collector-emitter voltage: 32V- Maximum collector current of 50 mA- Quantity: 2 units Code S0121 Available Price €0.62
Gravity: IO Expansion Shield for Arduino V7.1 Gravity: IO Expansion Shield for Arduino V7.1 is a shield board for Arduino that expands the capabilities of the I/O pins. Among other things, it has each pin with a power pair, the ability to include a 3.3 V voltage converter, a separate connector for I2C interfaces, SPI and a socket for XBee modules. Code DF027 Available Price €12.36
MQ-9 Carbon Monoxide Sensor Module MQ-9 Carbon Monoxide Sensor Module features:- Main chip: MQ-9 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 20ppm- 2000ppm carbon monoxide 500ppm- 10000ppm methane CH4 500ppm- 10000ppm LPG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0033 Available Price €2.39
Dallas Temperature Sensor Module DS18B20 The DS18B20 is a digital temperature sensor from Dallas Semi Conductors, used to measure ambient temperature or to carry out tests. It supports multipoint readings of the mesh networking type, being able to be deployed in three lines, in order to achieve these readings, it has a built-in pull-up resistance. Dallas Temperature Sensor Module DS18B20 features: - Operating voltage: 3 - 5.5 VDC - Measurement operating temperature: -55 ° C - 125 ° C - Output current: 5 μA - Accuracy of ± 0.5 ° C between -10 ° C and + 85 ° C - Storage temperature: -55 ° C - + 125 ° C - 100% new and high quality - Module DS18B20 temperature measurement sensor - The DS18B20 sensor has a pull-up resistor - Power indicator LED on the module Code S0124 Available Price €1.61
MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features: - Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Concentration detection: 200ppm - 5000ppm LPG, propane 300ppm - 5000ppm butane 5000ppm - 20000ppm methane 300ppm - 5000ppm H2 100ppm -2000ppm alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0027 Available Price €2.39