10x Male-Male Cables 20cm Jumpers Dupont 2,54 10x Male-Male Cables 20cm Jumpers Dupont 2,54 features: -Length: 20cm-Quantity: 10 cables-Connectors have male header contacts at either end-Compatible with female connectors 2,54mm-High quality and good working conditions-Easy to install and use Code K0007 Available Price €1.69
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €2.29
Peltier Ceramic Cell TEC1 12706 12V 60W Peltier Ceramic Cell TEC1 12706 12V 60W features: - Max Power: 60w - Voltage: 12v - Max Voltage: 15,2v - Max Current: 6A - Temperature Variation: - Peltier effect cell model TEC1-12706, 12v, max 60w and 6A, with a temperature difference between their faces of up to 67ºC Code M0055 Available Price €3.95
Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €5.50
10x Photoresistor GL5528 LDR Photoresistor is a resistor whose resistance decreases with increasing intensity of lightthat affects her 10x Photoresistor GL5528 LDR features: - Model: GL5528- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 10-20KΩ- Resistance with darkness (0lux): 1MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC- 10k - 20k Arduino PiC 5mm- Quantity: 10 units Code S0050 Available Price €0.15
5x Push Switch Button B3F Omron Blue Key 12mm 5x Push Switch Button B3F Omron Blue Key 12mm features:- 5x Push Buttons B3F Omron Key- Maximum current: 50 mA- Tension DC: 24V- Operating force: 1.27N- Switch terminals: weldable- Contact: SPST-NO- Contact resistance: 100M Ohm- Type of action: Superficial- Measures: 12x12x7.3mm Code K0074 Available Price €0.21
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.99
4-Channel 5V 10A Relay Module Characteristic: - Channels: 4 (independent protected by Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 54x 72mm - 5V Optocoupled 4-Channel Relay Module - This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for the remote control + 4-channel 315 MHz IC2262 receiver: - Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver Code RL007 Available Price €3.99
Load cell 10kg Load cell Load Cell Weight Sensor 10kg features: Load range: 10kg Operating voltage: 3VDC ~ 14 VDC. Rated output: 1.0 ± 0.15mV/V. Repeatability: 0.03% FS Effect of temperature on output: 0.01% F.S / ° C Temperature effect on zero: 0.05% F.S / ° C Code M0127 Available Regular price €3.49 -€1.00 Price €2.49
Load Cell Weight Sensor 50kg Pressure sensor sometimes called strain gauge. Load cell for measuring weights up to 50kg. The transducer measures the strain of the metal structure and converts it into a few mV. Code Sp096 Available Regular price €7.69 -€0.99 Price €6.70
HX711 Module Weighing Pressure Sensor 24 Bits The module uses a 24-bit high precision A/D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. HX711 Module Weighing Pressure Sensor 24 Bits features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0118 Available Regular price €2.79 -€0.47 Price €2.32
HX711 Modulo Conversor + Celda de Carga 2kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0120 Available Regular price €5.78 -€0.95 Price €4.83
Load Cell Weight Sensor 5kg Load cell Load Cell Weight Sensor 5kg features: - Load cell to measure weight up to 5kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 5kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0126 Last items in stock Regular price €2.99 -€0.99 Price €2.00
Ceramic Piezoelectric Disc 35mm with Mika PVC 49mm Characteristic: - Diameter: 35mm - Frequency: 2.3 kHz - Impedance (resonance): 300 Ohm - Capacity (at 1kHz): 25,000 pF - Dimensions: 35x0.50mm Code M0167 Available Price €0.49
Load Cell Weight Sensor 2kg Load cell Load Cell Weight Sensor 2kg features: - Load cell to measure weight up to 2kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 2kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0125 Available Regular price €2.99 -€0.99 Price €2.00
HX711 Modulo Conversor + Celda de Carga 5kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0121 Last items in stock Regular price €5.78 -€0.95 Price €4.83
Load Cell Weight Sensor 1kg Load Cell 1 kg Scale Sensor Weight Arduino Load cell to measure weight up to 1kgThe transducer measures the deformation of the metal structure and converts it into a few mV. Load cell Load Cell Weight Sensor 1kg features: - Load range: 1kg- Operating voltage: 3VDC ~ 14 VDC.- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / ° C Code M0124 Available Regular price €2.99 -€0.99 Price €2.00
HX711 Modulo Conversor + Celda de Carga 10kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0122 Available Regular price €6.28 -€1.45 Price €4.83
Load cell 10kg Load cell Load Cell Weight Sensor 10kg features: Load range: 10kg Operating voltage: 3VDC ~ 14 VDC. Rated output: 1.0 ± 0.15mV/V. Repeatability: 0.03% FS Effect of temperature on output: 0.01% F.S / ° C Temperature effect on zero: 0.05% F.S / ° C Code M0127 Available Regular price €3.49 -€1.00 Price €2.49
Load Cell Weight Sensor 50kg Pressure sensor sometimes called strain gauge. Load cell for measuring weights up to 50kg. The transducer measures the strain of the metal structure and converts it into a few mV. Code Sp096 Available Regular price €7.69 -€0.99 Price €6.70
HX711 Module Weighing Pressure Sensor 24 Bits The module uses a 24-bit high precision A/D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. HX711 Module Weighing Pressure Sensor 24 Bits features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0118 Available Regular price €2.79 -€0.47 Price €2.32
HX711 Modulo Conversor + Celda de Carga 2kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0120 Available Regular price €5.78 -€0.95 Price €4.83
Load Cell Weight Sensor 5kg Load cell Load Cell Weight Sensor 5kg features: - Load cell to measure weight up to 5kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 5kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0126 Last items in stock Regular price €2.99 -€0.99 Price €2.00
Ceramic Piezoelectric Disc 35mm with Mika PVC 49mm Characteristic: - Diameter: 35mm - Frequency: 2.3 kHz - Impedance (resonance): 300 Ohm - Capacity (at 1kHz): 25,000 pF - Dimensions: 35x0.50mm Code M0167 Available Price €0.49
Load Cell Weight Sensor 2kg Load cell Load Cell Weight Sensor 2kg features: - Load cell to measure weight up to 2kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 2kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0125 Available Regular price €2.99 -€0.99 Price €2.00
HX711 Modulo Conversor + Celda de Carga 5kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0121 Last items in stock Regular price €5.78 -€0.95 Price €4.83
Load Cell Weight Sensor 1kg Load Cell 1 kg Scale Sensor Weight Arduino Load cell to measure weight up to 1kgThe transducer measures the deformation of the metal structure and converts it into a few mV. Load cell Load Cell Weight Sensor 1kg features: - Load range: 1kg- Operating voltage: 3VDC ~ 14 VDC.- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / ° C Code M0124 Available Regular price €2.99 -€0.99 Price €2.00
HX711 Modulo Conversor + Celda de Carga 10kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0122 Available Regular price €6.28 -€1.45 Price €4.83